Setting up Mi true wireless headphones

Mi True Wireless Earbuds TWSEJ02LM User Manual

The headphones come with size M earmolds set, you can switch to size S or L if the set size does not fit your ear.

Using earbuds can reduce the perception of external sounds. Do not use the headphones in an environment that is unsafe. Outdoors, it is recommended to use only one earphone.

Parameters of the model at

Pay attention to adjust the earpiece so that the microphone is open during the call.

Xiaomi Mi True Wireless Earphones. полный обзор, топовые беспроводные наушники от Xiaomi

When talking, point the microphone of the earpiece towards your mouth to make the call clearer.

Charging

Before using the device, remove the protective film from the contacts of the earbuds to fully charge them and the charging case.

Use USB charging cable to charge the charging case.

When the headphones’ battery is low, you will hear a voice message. Put the headphones in the charging case, the indicator light will be red while charging, and turn white when fully charged, then turn off after 1 minute.

Turning on

When you take the earphone out of the charging case, it automatically turns on.

When the headphone is off, press and hold the touchpad for 1 second until the light turns white.

Turning off

Once you place the earbud in the charging case, it will automatically turn off.

When the headphone is on, press and hold the touchpad for 5 seconds until the indicator light turns red.

Using two headphones

Auto-connect: remove both headphones from the charging case at the same time and wait 2-3 seconds for the headphones to turn on automatically. When the right earbud indicator blinks white slowly, you can search for “Mi True Wireless Earbuds_R” in your device’s Bluetooth settings. If the headphones cannot be paired, put them back in the case and repeat the previous steps. After successfully pairing for the first time, the headphone will automatically connect to the previously paired device (Bluetooth enabled) when you turn it on.

Note. All headphones have been factory reset and can be directly paired to the device.

Manually connect: When the headphones are off, manually turn on both headphones. Both lights will flash white quickly, and the right earphone light will flash white slowly after the connection between the earphones is established. Turn on Bluetooth on your device, then connect your device or pair it with the headphones.

Using one headphone

Auto-connect: Remove one earphone from the charger and wait for the earphone to turn on automatically. The headphone indicator blinks white quickly and then blinks white slowly. Activate Bluetooth on your device and search for Mi True Wireless Earbuds_R or Mi True Wireless Earbuds_L, then pair your device with the right or left earbuds respectively. After successfully pairing for the first time, the headphone will automatically connect to the previously paired device (Bluetooth enabled) when you turn it on.

Note: The left earphone (L) has a relatively long automatic connection time.

Manual connection: When the headphones are off, manually turn on one of the headphones. When the light blinks white slowly, turn on Bluetooth on your device and pair the headphones to your device.

Reset the headphones

If the headphones do not connect properly, follow these steps to reset: Remove the headphones from the charging case and make sure they are off. Press and hold the touchpad on both headphones for approximately 15 seconds. After the indicator light flashes red and white three times alternately twice, release the panel and place the headphones back in the charging case. Remove the headphones from the list of paired devices on your device, then pair them again with your device.

Completeview feature

You can use the following functions on both headphones:

Answer / end call

Gently touch one of the earbuds to answer/end a call.

Press and hold the touchpad for 1 second to reject a call.

Play / pause music

From standby gently touch the touch panel to play / pause music.

Note. Music player should be running in the background.

Activate the voice assistant

In standby mode, gently tap the touchpad twice to activate the voice assistant.

Note. Your device must support and activate the voice assistant and quick wake-up features.

Answer a second call / switch between calls

When a call comes in, gently touch one of the headphones to answer the call. During a call, gently tap one of the earpieces to answer a second incoming call. Gently tap one of the headphones twice to switch between the two calls.

Switch between headphones and device

During a call, press and hold the touchpad for 1 second to toggle between the headphones and the phone.

Mute / unmute

During a call, gently tap the touchpad twice to mute/unmute.

Features

Name: Mi True wireless headphones.

Wireless range: 10m (no obstacles)

Battery capacity: 43 mAh (per earphone)

Bluetooth Profiles: HFP / A2DP / HSP / AVRCP

Features

Bluetooth 5.0, compatible with most Bluetooth enabled devices on the market

Touch control for improved user interaction

Product, accessory and user interface illustrations in the user manual are for reference only. Actual product and features may vary due to product improvements.

Precautions

• Please fully charge this product before first use.
• If the product has not been used for more than 2 weeks, it is recommended to charge it before use.
• Use only certified chargers supplied by qualified manufacturers.
• The pairing function will be disabled if the headphones are not used for a long time. If your device cannot find the headphones, check if the headphones are in pairing mode. If you are unable to pair the headphones with the device, try restarting the headphones or device or clearing the pairing history, and then try pairing again.

Due to the connection characteristics of the Bluetooth signal in dense environments with electromagnetic interference at frequency 2.4 GHz there may be occasional disconnects or no sound.

• Do not disassemble, repair, or modify the product for any reason, as it may cause a fire or even completely destroy the product.
• Do not expose the product to environments where the temperature is too low or too high (below 0°C or above 45°C).
• Keep the product display away from the eyes of children and animals during use.
• Do not use this product during a lightning storm. Lightning may cause the product to malfunction and increase the risk of electric shock.
• Do not clean this product with alcohol or other volatile liquids.
• Avoid contact with liquids.
• Excessive sound pressure from headphones can cause hearing loss.

RISK OF EXPLOSION IF BATTERY IS REPLACED BY THE WRONG TYPE.

DISPOSE OF USED BATTERIES ACCORDING TO INSTRUCTIONS

To prevent possible hearing damage, do not listen to music at high volume for long periods of time.

All products marked with this symbol are Waste Electrical and Electronic Equipment (WEEE as per Directive 2012/19 / EU) which should not be mixed with unsorted municipal waste. Instead, you should protect human health and the environment by handing over your used equipment to a special collection point for Waste Electrical and Electronic Equipment designated by the government or local authorities. Proper disposal and recycling will help prevent possible negative effects on the environment and human health. Please contact the installer or local authorities for more information about the location as well as the conditions of use of such collection points.

Storage temperature: 0 ° C to 45 ° C

Mi True TWSEJ02LM Wireless Headphones User Manual. Optimized PDFThe Mi True TWSEJ02LM Wireless Earbuds User Manual. Original PDF

Related Manuals/Resources

True Wireless Earbuds User Manual

Blackweb True Wireless Earbuds BWD19AAH User Manual, blackweb True Wireless Earbuds BWD19AAH User Manual. optimized PDF file, blackweb.

EarFun Air True Wireless Earphones User Manual. Product diagram. Charging specification. How to install.

True Wireless Earphones Owner’s Manual Remove the earphones from the charging case, and they will automatically turn on.

Mi True Wireless Earphones 2S user manual

Product, accessory, and user interface illustrations in the user manual are for reference only. Actual product and features may vary due to product improvements.

Instructions

Charging

• Charging the headphonesWhen the headphones are placed in the charging case, they will automatically begin charging.
• Charging the charging caseUse the Type-C charger to charge the charging case, or place the charger light on a compatible wireless charger. The red light blinks while charging and the white light turns off air charging for 10 seconds.

Note: Headphones are turned off before first use. To activate them, place them in the charging case and press the button for 5 seconds. We recommend that you fully charge the headphones. before using them for the first time.

Checking battery level

• Checking the battery level of the headphonesWhen the headphones are connected to the phone, you can check the battery level of the headphones in the phone status bar.Note: The battery level is always displayed in the phone status bar.the earpiece with the lowest battery level. This feature is not supported on some phones.
• Check the battery level of the charging caseOpen the cover of the charging case or press the function button if the cover is closed:① When the charger light is on for 5 seconds, it means there is enough battery power.② When the charging case light blinks, it means that the battery level is low and you need to charge it immediately.
• Check baery level with your MiPlace the headphones in the charging case and close the lid after successfully connecting to the phone. Make sure your Mi phone has Bluetooth enabled. Hold the phone against the charger and open the charger cover. A notification will appear on your phone and you can check the battery level of the headphones and the charging case.Note: When checking the battery level of your phone, please update your Mi phone to the latest stable version. This feature is currently only supported by certain Mi phones.

Turning on

When you open the charging case, the headphones automatically turn on.

Sleep Mode

Place the headphones back in the charging case and close the lid. The headphones will turn off and automatically go into sleep mode.

Model Settings on

Connecting

Connect headphones to your new device

• Put the headphones in the charging case and close the lid. Ensure that your Mi phone has Bluetooth enabled. Hold your phone near the charger and open the charger cover. Follow the instructions on your phone screen to connect to the headphones.Note: Quick connect feature is currently only supported by some Mi phones, please update your Mi phone to the latest stable version.
• Connection interruptedWhen Bluetooth is disconnected on the device or the headphones are out of range, the headphones automatically go into connection standby mode. If the headphones remain disconnected from your device for 5 minutes, they will go into suspend mode. If you put the headphones back on, wake them up and enter connection standby mode.
• Automatic connectionWhile the headphones are in the charging case, when you open the case, the headphones automatically connect to the last used Bluetooth device. If no connection history is detected or the headphones cannot successfully connect to a Bluetooth device, the headphones automatically go into connection standby mode.Note: If the headphones cannot automatically connect to the device, you must manually connect the headphones to the desired device using the Bluetooth device settings.Due to the connection characteristics of the Bluetooth signal in dense environments with electromagnetic interference at frequency 2.4 GHz there may be occasional disconnects or no sound.

Clear the connection history

① Place the headphones in the charging case.Press and hold the function button on the charging case for more than 10 seconds. When the light flashes red and white alternately, release the button.③ The connection history has been deleted and the charging case light flashes white. Then the headphones are waiting for pairing.

Completion function

• Incoming callsTouch one of the headphones gently twice: answer/end call
• Music and voice assistantWhen wearing both earphones: Gently tap the right (R) earphone twice: play/pause music Lightly tap the left (L) earphone twice: access the voice assistant. Ejecting the earphone: Pause music playback. : Play/pause musicNotes:① The voice assistant feature can only be used if your device supports it and this feature requires permission on your device.If you are using only the left earphone, put the right earphone in the charging case and close the cover.

Specifications

Model: TWSEJ07WM PureWeight: 52gInput: 5V 1A Charging Port: Type- Resistance: 32Ω Charging Time: Approx. 1 hoursWireless connectivity: Bluetooth 5.0Bluetooth Profiles: BLE / HFP / HSP / A2DP / AVRCPSupported Audio Codecs: SBC / AAC / LHDCWireless Range: 10m (open space without obstacles)Headphone Standby Time (stand alone): Approx. 5 hoursTotal battery life (with charging case): Approx. 24 hoursBluetooth operating frequency: 2402-2480 MHz (for EU)Maximum transmit power for BT: 10 dBm (for EU)Maximum transmit power for BLE: 10 dBm (for EU)

WEEE information

All products marked with this symbol are Waste Electrical and Electronic Equipment (WEEE according to Directive 2012/19 / EU), which should not be mixed with unsorted household waste. Instead, you should protect human health and the environment by transferring your used equipment to a designated electrical and electronic waste collection point designated by the government or local authorities. Proper disposal and recycling will help prevent potential negative consequences for the environment and human health. Please contact the installer or local authorities for more information about the location as well as the conditions of use of such collection points.

Tiinlab hereby declares that radio equipment type TWSEJ07WM complies with Directive 2014/53 / EU.The full text of the EU Declaration of Conformity is available at the following internet address: www.Mi.com

Safety Warning

• Do not expose batteries or battery packs to excessive heat such as sunlight, fire, etc.п.
• Replacing the battery with the wrong type of battery, which may violate safety precautions (e.g. fire, explosion, corrosive electrolyte leakage, etc. Д.).
• Disposing of the battery in a fire or hot oven, mechanically crushing or cutting the battery, which may cause an explosion.
• Leaving the battery in an environment with very high temperatures could cause an explosion or leakage of flammable liquid or gas.
• The battery is exposed to extremely low air pressure, which can cause an explosion or leakage of flammable liquid or gas.
• Risk of explosion when replacing the wrong type of battery.
• Dispose of used batteries according to the instructions.
• The maximum ambient temperature when using the product is 40 ° C.

To prevent possible hearing damage, do not listen at high volume levels for a long time.

The symbol indicates direct current.tage

The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc., and any use of such marks by Xiaomi Inc. Is made under license. Other trademarks and trade names belong to their respective owners.

NOTICE OF WARRANTY

As a Xiaomi consumer, you receive additional warranties under certain conditions. Xiaomi offers certain consumer warranty benefits that are in addition to, and not in lieu of, any legal warranties under your local consumer protection laws. The duration and terms of legal warranties are governed by the respective local laws. For more information about the benefits of consumer warranty, please refer to Xiaomi Official Representative in Georgia website: https://www.Mi.com/en/service/warranty/. Unless prohibited by law or otherwise promised by Xiaomi, air sale services are limited to the country or region of original purchase. Under the consumer warranty, to the maximum extent permitted by law, Xiaomi will, at its sole discretion, repair, replace or refund you. Normal wear and tear, force majeure, abuse or damage caused by user negligence or error is not covered by warranty. The contact person for air sale service may be any person in Xiaomi’s authorized service network, authorized Xiaomi distributors, or the end supplier who sold you the products. In case of doubt, contact the appropriate person Xiaomi can identify.This warranty does not apply in Hong Kong and Taiwan.These warranties do not apply to products that were not properly imported and/or were not properly manufactured by Xiaomi and/or were not properly purchased from Xiaomi or an authorized Xiaomi retailer. In accordance with current law, you can use the warranties of the unofficial seller who sold the product. Therefore, Xiaomi suggests that you contact the retailer from whom you purchased the product.

Mi True Wireless Earphones 2S User Manual. Optimized PDFMi True Wireless Earphones 2S User Manual. Original PDF

To connect or reset in Mi True Wireless Earphones 2 model, you need to press the function button on the case, in Basic touch panel on the headphones. For technical specifications. Mi True Wireless Earphones 2S Audio Codec Support: SBC/AAC/LHDC.

This is done as follows: the headphones are unplugged, then the panels on both are clipped until the red. Repeatedly clamp the panels for half a minute. As a result of these actions, the white light should blink, and after another 10 seconds, the red-white light. Further holding and will cause the required full reset.

Place both headphones in the charging case and remove them when the red light turns on and charging begins. The headphones will automatically turn on and connect to each other. If they still don’t connect to each other, refer to the user manual to reset them.

Turn on Bluetooth and search for available devices. The device we need is called Mi True Wireless EBs Basic_R. This is the right earphone. You click on this name and accept the pairing request where you can allow the contacts to be exchanged.

How to set up the Xiaomi wireless headphones

Before you start connecting the Xiaomi headphones to your phone, make sure the headset is fully charged. To do this, just look at the color of the LED on each earphone. Usually if the LED blinks blue, the battery is fully charged, if it blinks red, it is empty.

Xiaomi makes many varieties of wireless headphones: the Redmi AirDots, Mi True Wireless Earbuds, Mi Collar and Mi Sport. You can also find other kinds, which will differ from the previous version with the prefix PRO. Depending on the model of the headset, the principle of connection and configuration may differ, so in advance with the included instructions. But, as a rule, to connect Xiaomi wireless headphones to the phone you need to do the following:

• Turn on the headphones by pressing the touch or mechanical button.
• After that, once again press the button and hold it until you hear a beep, indicating readiness for connection.
• Go to phone settings and turn on Bluetooth.
• Wait until the device appears in the list of available devices. If nothing appears, you can press the “Refresh” button. Also make sure that the blue light on each of the headphones is blinking.
• Tap the headphone model in the list and wait for pairing. In the window that appears on the screen, you need to select “Accept”.

Now when you turn on Bluetooth wireless headphones will automatically connect to your phone. To cancel the permanent pairing you need to follow these steps:

In order for the headphones to be displayed in the list again, you must perform the connection steps again.

Mi True Wireless Earphoness ( Xiaomi Mi AirDots Pro ). universal wireless headphones from the world famous manufacturer Xiaomi

Xiaomi announced and released the Mi AirDots Air Pro professional wireless headphones in January 2019. The model comes in a branded box, decorated in white and blue. The inscription on the front of the package informs you that in front of you are genuine wireless headphones from Xiaomi:

The word Air, written in large letters, reminds you that the sound will be transmitted through the air, without the use of wires.

• Actually two wireless headphones, ready to use;
• Three additional interchangeable pairs of silicone earbuds of different sizes;
• A case that is used for charging and convenient storage (docking station);
• USB (type C) cable to connect to mains or computer.
• communicate with a device using Bluetooth 4 technology.2 at a distance of up to 10 meters (in the absence of obstacles such as concrete or metal walls);
• Use Active Noise Cancellation (ANC) technology so you can listen to music, speech or other sounds even when you’re in town, in cafes, on public transport or other crowded places;
• controlled by a touch sensor located on the back of the earpiece, also equipped with an infrared sensor
• The headphones are waterproof to IPX4. in practice this means you can use the headphones even in the rain or in humid air without fear of damaging them;
• support work not only with Xiaomi smartphones, but also with any other devices with Bluetooth connection, including mobile (Android, iOS and others) and stationary (Windows, Mac, Linux and so on).

Note: Xiaomi makes no secret of the fact that it released the Mi AirDots Air Pro as an alternative to similar wireless headphones from Apple. The noticeable difference is that the “apple” headphones, having almost similar characteristics, cost significantly more. Thus, “Xiaomi” once again confirms its ability to do quality without forcing the buyer to overpay.

• take the headphones out of the case if they are in it;
• Make sure the headphones are charged and active;
• turn on Bluetooth on your smartphone if it is turned off;
• Look for Mi AirDots Air Pro in the list of available devices and plug them in.

Automated headphone control Among the provided settings is the automatic pause function. Built-in infrared (IR) sensor detects that you’ve removed the earpiece from your ear. If you were listening to music at that moment, the playback will automatically pause. As soon as you insert the earphone again, the IR sensor will recognize this and playback will start from the same place. You can also control the Mi AirDots Air Pro with a touch sensor (touch pad). It allows you to pause and resume playback, control it while listening to music or audiobooks, and answer phone calls.

Charging and recharging Mi AirDots Pro The headphones themselves are designed to last up to 3 hours of autonomous use. They start signaling you to recharge when the built-in mini rechargeable batteries drop to a critical level. Intermediate recharging is possible with the case, which is also a docking station. Slide the headphones into the case so the contacts are at the bottom. Not difficult to do, as the shape of the case is optimized for Mi AirDots Pro: A fully-charged docking station battery lasts for an average of three headphone recharges. Thus, their total battery life can be extended to about 10 hours. Given that the case weighs only 58 grams, you can easily take it with you on trips and hikes. In turn, the battery of the docking station is charged using the cable that comes with. Using a standard USB adapter. Can plug into a power outlet. If you don’t have one, you can use a USB port on your computer. However, keep in mind that then less power will be supplied and charging will be slower.

Conclusions Mi AirDots Pro. comfortable and functional wireless headphones. No worse than its Apple counterpart, but significantly cheaper. Compatible with any device with Bluetooth, including iPhones, iPads, and Macbooks; uses minimum power; connects and configures effortlessly. Automated control, moisture resistance, noise suppression make Mi AirDots Pro versatile. You can use them to listen to music, audiobooks, live speech; sound from a movie, an app or a game. The clear advantages: no wires and the associated inconvenience, excellent communication at a distance of up to 10 meters, automatic pause. You can use the touch sensor to control. The case, which also acts as a docking station, allows you to use the Mi AirDots Pro for hiking, camping, traveling, traveling on public transport, business trips and holidays in almost any place. InstructionHow to use the headphones can be found in the link instructions for Xiaomi Mi AirDots Pro

How to connect Xiaomi AirDots.

Connecting Xiaomi AirDots is not too difficult, but you can’t do without instructions. Xiaomi AirDots instructions:

• Press the buttons on both headphones until the red light appears.
• Put the headset in the charging case. Next, take the headphones out of the case and wait until they pair up.
• Turn on the Bluetooth on your smartphone and wait until the accessory appears in the list of available devices.
• When you click on the Mi True Wireless EBs Basic_R (as the headset will be called), the connection is made. The smartphone will connect to the right earpiece, and that will automatically connect the left one.

It happens that the smartphone does not see the left headset. This happens when there is an unsynchronization. How to connect Xiaomi AirDots in this case. Try these actions:

After that, they should connect to your smartphone. If you have trouble, the headset comes with detailed instructions on how to connect it.

Connecting Mi True Wireless Earbuds Basic to your phone

Many people note the unusually large packaging in which the headphones arrive at the customer. The manufacturer could simply put the whole small set in a package that would be half the size.

If you had to open the Mi True box yourself, you will notice that it is almost a third empty.

The set of original Mi True Wireless Earbuds Basic from the popular Chinese manufacturer Xiaomi includes a case with headphones, earbuds, instructions.

For some reason Xiaomi has not placed a cable to charge the case, which is usually put to your cell phone. For this you will need to buy it yourself. Case needs to charge the cable with connector microUSB / USB. Today this type of charging cables and devices is the most common. Most users have one at home. The case is made of brushed plastic, as is the case of the headphones. There is a cover that opens with little effort. In the middle of the case there are two niches in which fit headphones.

So to add or remove the sound in the headphones on your smartphone uses other ways, which you are now learning about. They, by the way, are suitable for any operating system (iOS, Android) and manufacturer Samsung, Xiaomi, Huawei, Honor, JBL, Apple, etc.

Making the sound louder with the buttons on the phone

The most obvious way to change the volume is with the corresponding function buttons on the phone, which is paired with these headphones.

After all, in fact, TWS headphones or standard Bluetooth headset (when the headphones are combined by a wire) is different from wired headphones only way to connect to your smartphone. Otherwise it’s the same headphones, which means you can add or subtract sound through the phone.

Increase the sound in bluetooth headphones through the smartphone menu

I do not know why (when there are buttons), but the same can be done through the settings menu in the phone. On Android, go to Sound & Vibration

And with the slider to change the Media Volume. Adding to the right, reducing to the left. Here you can change the volume of the ringtone, alarm clock, ring tone and notifications.

How to make wireless headphones louder through a proprietary app

Not all, but some models TWS earbuds support their control from a branded application that is installed on the phone.

In addition there is a huge number of other features. For example, the equalizer to adjust the details of the sound of the track. Or even changing the assignment of the function button.

Turning up the volume with the control buttons on the headphones

Again, not all headsets have the ability to change music playback volume via gestures on the control button. But even in inexpensive models they are found. In this case, it is most often necessary to press the right wireless earpiece once, twice or three times (depending on the specific model) to zoom in. And to decrease to the left. To find out which action corresponds to adjusting the sound in your case, look at the specifications of your headset

If the Bluetooth headset has a mobile app, it often has the ability to change the assignment of gestures for ease of use. For example, if double-tapping a key meant to switch to the next or previous track, it can be reprogrammed to adjust the sound volume.

Changing the speaker through the voice assistant

If the TWS headphones are not provided by the manufacturer, you can always use them to call the voice assistant. And ask him to increase or decrease the volume. To do this, look at the instructions and find out which gesture is responsible for addressing the assistant.