Why is music from the outside through headphones hear.

Extraneous sound and noise in headphones and columns: where does it come from and how to eliminate it

Most home computers (and laptops) are connected by speakers or headphones (sometimes both). Quite often, in addition to the main sound, the speakers begin to lose all sorts of extraneous sounds: the noise of the mouse scrolling (very common problem), various crackling, trembling, sometimes a light whistle.

In general, this question is quite multifaceted-dozens can be the reasons for the appearance of extraneous noise I want to point out only the most common reasons in this article, because of which extraneous sounds appear in headphones (and columns).

By the way, maybe an article with the reasons for the lack of sound will come in handy: https: // PCPRO100.info/Net-Zvuka-Na-Kompyutere/

The reason is the problem with the cable for connecting

One of the most common reasons for the appearance of extraneous noise and sounds is a poor contact between the sound card of the computer and the sound source (speakers, headphones, etc.). Most often, this is due to:

  • damaged (broken) cable, which connects the speakers to the computer (see. rice. one). By the way, in this case, you can also observe the following problem: there is a sound in one column (or headphone), but in the other there is no. It is also worth noting that the broken cable is not always visible by eye, sometimes it is necessary to install headphones to another device and test to get to the bottom of the truth;
  • bad contact between the PC network card and headphone plugs. By the way, very often it helps to just remove and insert a plug from the nest or turn it with a clock (against an hour) arrow to a certain angle;
  • not fixed cable. When he begins to hang out from draft, pets, etc extraneous sounds begin to appear. In this case, the wire can be attached to the table (for example) with ordinary tape.

By the way, I also observed the following picture: if the cable for connecting the speakers is too long, extraneous noises may appear (usually barely distinguishable, but still annoying). With a decrease in the length of the wire. the noise disappeared. If your speakers are very close to PC-maybe you should try to change the length of the cord (especially if you use some extension cords).

In any case, before starting a search for problems. make sure that with “iron” (columns, cable, plug, etc.) everything is fine. To check them, it is enough to use the other PC (laptop, TV, etc. devices).

The reason is the problem with the drivers

Because of problems with drivers, anything can be! Most often, if the drivers are not installed, you will not have a sound at all. But sometimes, when the wrong drivers were installed. not quite the correct operation of the device (sound card) may be observed and therefore various noises appear.

How To Have Your Headphones And Speakers Working At The Same Time

Problems of this nature also often appear after reinstalling or updating Windows. By the way, Windows itself very often reports that problems are observed with drivers.

To check if everything is in order with the drivers, you need to open the device manager (control panel \ Equipment and sound \ Device manager. see. rice. 2).

In the device dispatcher you need to open the “Audio.Office and Audio Exit” tab (see. rice. 3). If yellow and red exclamation signs are not displayed in this tab opposite the devices, it means that there are no conflicts and serious problems with the drivers.

By the way, I also recommend checking and updating the drivers (if updates are found). Upon updating the drivers, I have a separate article on the blog: https: // PCPRO100.info/obnovleniya-Drayverov/

The reason is the sound settings

Quite often, one or two ticks in sound settings can completely change the cleanliness and sound quality. Enough often interference in sound can be observed due to the included PC beer and linear entrance (and. pieces, depending on the configuration of your PC).

To configure the sound. go to the control panel / equipment and sound and open the “volume setting” tab (as in rice. four).

Next, open the properties of the Dynamics and head phones device (see. rice. 5. just click with the left mouse button on an icon with a speaker).

The “Levels” tab should have the treasured “PC Beer”, “CD of the Disk”, “Line input”, and pr. (cm. rice. 6). Reduce the level of the signal (volume) of these devices to a minimum, then save the settings and check the sound quality. Sometimes after such entered settings. the sound changes dramatically!

Reason: volume and quality of the columns

Often hissing and crackle in columns and headphones appear when their volume strives for the maximum (some noise appears when the volume becomes above 50%).

This is especially common with inexpensive models of columns, many call this effect “trembling”. Please note: perhaps the reason is just this. the volume on the columns is added to almost the maximum, and in Windows itself is reduced to a minimum. In this case, just adjust the volume.

In the headphones, only music is not heard, what to do?

Headphones have become an integral attribute of modern smartphones and other electronic devices. However, they often fail. We will talk about one of the common problems and methods for its elimination in our article.

The user was faced with a situation where there is a sound in the headset, and speech is barely distinguishable or not played. The reasons for this can be distinguished into two categories.

The first source is associated with the accessory itself:

The second option indicates a problem in electronics:

  • The plug is incorrectly connected to the audio connector, or the latter is faulty,
  • The driver is out of order or failed,
  • On some devices there is an option “Karaoke”, in working mode, it prevents the functioning of audio equipment,
  • The volume sound can conflict with a connected model.

IMPORTANT. In the production of cheap products, low.quality materials and components are used, which increases the risk of their frequent breakdowns and unstable operation.

Ways how to eliminate the problem

First of all, we determine the source of the problem:

Sound does not come from speakers but only from the headphones only

Connect the headphones to another device. It often happens that the accessory connected to the computer gives an erroneous sound, and when connecting to the phone, the problem disappears.

Connect another equipment to the PC connector (columns, etc. D.).

The procedure for incorrect work of the headset:

  • We try to change the settings, for this we pass the control panel along the way. equipment and sound (sound). playback. On the last tab, select the headphones and press the properties. levels. button balance. On the left channel we set 50, with the right side we will have to experiment at different levels until you reach the optimal sound of the voice.
  • You can set the value of the left part 100, right. 0. According to users, this method has helped many to restore normal sound.

NOTE. Depending on the OS, the name of the sections may vary slightly.

As an option, in the section Properties go to the additional features section and turn off all the effects in the window if they are activated.

In the case of a cable break for independent repair, knowledge of the basics of soldering is necessary.

The device will help determine the place of cable damage. The wire can most often be wrapped around the headphones or next to the plug. Carefully clean these areas and check for integrity. Then eliminate the problem.

REFERENCE. The malfunction can be in the plug itself, in this case you have to purchase a new part.

If problems with the accessory are not found, let’s start with the audio entrance to the PC:

  • We examine the nest, when the extraneous inclusions are detected, carefully remove the pollution.
  • Mechanical damage to the contact part will require port replacement. It can also be fixed on its own with the help of soldering, eliminating the places of cliffs on the tracks.
  • In some cases, the plug can hang out in the connector. Make sure the connection density, in case of poor contact, purchase an adapter.

We proceed to checking the software part:

We check the relevance and performance of the drivers. Start. control panel. sound, activate the device manager. In the window that opens, we open the point of sound, video and gaming devices. We look if there is an exclamation mark next to the desired device. Using PKM, select in the context menu “Update Drivers”.

ON A NOTE. You can go to the site of the manufacturer of the sound card and download the necessary application according to the version of your PC.

The “Karaoke” tool can be found and disabled if the properties are in the section using the improvement tab. If there is an activated point in it, the vote suppression, remove the flag.

The Windows Sonic option (voluminous sound) is turned off into the track, use PKM on the speaker image and select a spatial sound (turn off).

If a problem arose on a smartphone, we act according to the scheme:

If you recently installed a new utility for sound (for example, an amplifier), then we try in stages (depending on the result) methodology:

NOTE. It makes sense to attribute a headset to a service center with a high cost of model. In other cases, the purchase of a new device will be less costly.

In our article, we set out in detail the possible reasons for the lack of voice in the headphones and ways to eliminate problems. We hope that the material helped you solve this issue.

Why in headphones inaudibly voices only music

The user was faced with a situation where there is a sound in the headset, and speech is barely distinguishable or not played. The reasons for this can be distinguished into two categories.

The first source is associated with the accessory itself:

The second option indicates a problem in electronics:

music, headphones, hear
  • The plug is incorrectly connected to the audio connector, or the latter is faulty,
  • The driver is out of order or failed,
  • On some devices there is an option “Karaoke”, in working mode, it prevents the functioning of audio equipment,
  • The volume sound can conflict with a connected model.

How to eliminate the problem?

First, insert the headphones into another device (preferably several) and determine what you need to work with: with electronics or with your favorite accessory?

music, headphones, hear

If it turned out that the case is in electronics, then try to change the settings in mixers/equalizers. In the standard way on PC, this is done through the “control panel”. Select in it the “Equipment and Sound” section, then click “playback”. In this section, find the device “Headphones” and go to their properties. Your task is to change the sound balance. Most often, it is possible to return a good sound if you unscrew the left ear by 100, and the right, on the contrary, lower to zero to zero. Along the way, in the settings, make sure that all additional sound effects are disabled (Echo, 3D, reverb, etc. P.). they can also create problems.

Check the version of the last installed driver as a prevention. Enter the Windows “Device Manager”, select “Sound devices” and, clicking on the right mouse button, select “Update the driver”. The last released drivers with updates can also be downloaded from the official sites of your device.

In case of damage to the headphone cable, you can try to independently stock up the wire. Use the multimeter to determine the gap site and combine the wiring using a conventional soldering iron and rosin. This method is suitable only for those who previously engaged in soldering or at least have a clear idea about this. Usually the sound of headphones is distorted due to a break in the grounding wire. Most often, he is in the braid of golden or brown and has several veins. The sound will not change until at least one of these veins function. After the headphones are sealed, you can apply folk trick in the form of installing a small spring on top of the wire at the base of Jack. This will not allow the wiring to rely again during operation.

The problem can lie in Jack itself. In this case, it will be cheaper and faster to just buy a new part, and not engage in independent repair.

If a bad sound appeared on a smartphone, then first check the entrance socket itself. Due to the fact that the phone is often in a or handbag, garbage can get into the nest, which will affect the sound quality. Simple purposes inputs will help. Also check the equalizer settings and install them “by default”.

In the end, you can buy headphones of the same brand or try another. The fact is that any device has its own service life. This is the modern sales market.

There is no voice in headphones, only music plays

Headphones occupy a special place in the category of the most popular things in the daily life of a modern person. Most often we choose the only one of the huge assortment and get used to their sound, shape and design tightly. But, like any thing, headphones tend to fail, sometimes in a very strange way. Let’s try to figure out why music, for example, is heard in headphones, but there is almost no voice?

Problems with sound can be if Jack is not trite into the connector to the end or something prevents him from this. An important factor is also the use of old sound drivers or the included function such as “karaoke mode” or “volumetric sound”.

It is logical to assume that the reason for this ailment is either in the headphones themselves or in the device where they are connected.

  • The accessory may fail only due to poor quality or due to improper operation. Check the integrity of the wire along the entire length, especially at the base of the “jack” and the headphone building. Often, cheap headphones gnaw at wiring, the braid of which is made of low.quality materials.
  • Headphones can be intended for operation only with specific devices or brands and therefore are incompatible with your gadget.
  • Low product quality. The product itself can be unscrupulous, which has entailed such poor audibility of average frequencies.

How to eliminate the problem?

First, insert the headphones into another device (preferably several) and determine what you need to work with: with electronics or with your favorite accessory?

If it turned out that the case is in electronics, then try to change the settings in mixers/equalizers. In the standard way on PC, this is done through the “control panel”. Select in it the “Equipment and Sound” section, then click “playback”. In this section, find the device “Headphones” and go to their properties. Your task is to change the sound balance. Most often, it is possible to return a good sound if you unscrew the left ear by 100, and the right, on the contrary, is reduced to zero to zero. Along the way, in the settings, make sure that all additional sound effects are disabled (Echo, 3D, reverb, etc. P.). they can also create problems.

Check the version of the last installed driver as a prevention. Enter the Windows “Device Manager”, select “Sound devices” and, clicking on the right mouse button, select “Update the driver”. The last released drivers with updates can also be downloaded from the official sites of your device.

In case of damage to the headphone cable, you can try to independently stock up the wire. Use the multimeter to determine the gap site and combine the wiring using a conventional soldering iron and rosin. This method is suitable only for those who previously engaged in soldering or at least have a clear idea about this. Usually the sound of headphones is distorted due to a break in the grounding wire. Most often, he is in the braid of golden or brown and has several veins. The sound will not change until at least one of these veins function. After the headphones are sealed, you can apply folk trick in the form of installing a small spring on top of the wire at the base of Jack. This will not allow the wiring to rely again during operation.

The problem can lie in Jack itself. In this case, it will be cheaper and faster to just buy a new part, and not engage in independent repair.

If a bad sound appeared on a smartphone, then first check the entrance socket itself. Due to the fact that the phone is often in a or handbag, garbage can get into the nest, which will affect the sound quality. Simple purposes inputs will help. Also check the equalizer settings and install them “by default”.

In the end, you can buy headphones of the same brand or try another. The fact is that any device has its own service life. This is the modern sales market.

How to make no one heard anything when I listen to music through headphones

I’m looking for a simple way to check if people around me hear any sounds from my headphones.

Of course, there is always the opportunity to remove the headphones for a moment and listen, if you hear something without putting them on, but since the volume and bass are not the same in every song, this is probably the wrong way. go if you are in public places (for example, on a train).

So does anyone have an effective and, possibly, a more secret way to check this?

Use your smartphone to recording sounds. Start by bring the device to your ear while listening to music in headphones, then gradually push the phone from your ear to understand how far the sound of the headphones spreads. You can reproduce the record to get an idea of ​​what other people can hear. You must also install a control sound like your ordinary voice, and write it down. Thus, you can attribute the sounds of headphones to the sound of control.

Tip: use something except a recording phone as source of music in headphones.

An option to improve this can be said in an ordinary voice, how far you keep a recorder. That is, to say “next to the ear”, write down for a while, “the next person / 0.5 m / 3 feet”, write down for a while, etc. D. Thus, when you listen to the record, you can feel the distance for different parts.

@holroy or you can make a video that will record audio. If the camera is aimed at your head, you will see how close or far it is.

Yes, the calibration step is important. There is no significant evidence that the microphones of smartphones perceive the noise of the same level as our ears (and this probably also depends on the frequency).

Put on the headphones on the armrest of the sofa, as if the armrest of the sofa had to wear them. Now play your music. You can use various hand substitutes.

The operator says that these are inhabitants, which are not easy to place in another place. Although the usual headset can be placed like this, and I found that the upper thigh is a good place to simulate the head in terms of sound. absorption.

I haven’t seen it so cool about the idea of ​​the thigh, thanks! It makes sense that it will work better and much more convenient!

Download the sound test musical file that reproduces a fairly wide range of frequencies from bass to top, so you checked it to suit almost every song in your playlist. Take the headphones and listen. After you put on the headphones, the volume of the surrounding sound decreases, since the sound waves are contained inside your ear, slightly bounced around and weaken.

One of the key sound distribution factors will be the case material, that is, cheap plastic with a gap between the case and the plug will not contain the sound very well. Thus, a small hint will be to seal any cracks and around the body / plug so that the sound waves do not leave your ear!

I would also recommend using rubber plugs, as they will take the shape of your ear containing sound.

After reading a lot of answers, almost everyone just says the same thing for recording sound, and then listen or ask someone. In addition, since you need a “hack” or “shortcut”, which should require only your assessment, so my proposal will be quite obvious,

  • Keep the headphones at a low volume level so that you can distinguish music and surrounding sound (so that you can also be attentive to your environment!)
  • Hold the headphones on the table at home and try using different sound levels to find out if you hear the sound or not.

Listen to your favorite music at the desired volume level. Perhaps a little louder. And ask a friend or relative if they can hear your music. You can also ask a friendly stranger if you are alone in the world.

If they can hear music, reduce the volume until they hear it.

Perhaps you will try it a couple of times until you are satisfied with the answer and sound level.

There are many useful people around that could help you in this.

Since people have various rumors, it does not always work. When you ask my father, music can be quite loud before he hears her, if he hears at all. Ask me, and you will not have a sound before I mention this. (And not only when he is asked.)

@Willeke may be true for you. You will have to ask your own question to solve your specific circumstances. Perhaps Wayneera does not know you or your father and will be glad to answer your friends, relatives or acquaintances. Your sensitivity may need special equipment and support. I do not know a single answer that will always work for everyone. This sets the standard outside the practical answer.

Well, this is a very difficult question. I would also recommend you to wear a headset from rubber material, as they are ideal for your ears. But besides this, you really will not know if someone is already looking at you due to the noise coming from your headset. Try using the headset at home and check if it is noisy, even if it is connected to your ears. If the sound still sounds, you should think about alternatives to satisfy your requirements

There is no sound in headphones on the phone: 10 tips to those who have disappeared

In general, the phone, judging by statistics, is much more reliable in terms of sound than PC (this is in Windows-either the wrong sound card is chosen, then something is connected, then in BIOS something is wrong, etc.P.). However, not a single trouble.free gadget has yet been created.

In this small note, I decided to collect 10 most popular tips and recommendations that help with “low blood” to solve the problem of lack of sound in headphones on the phone. I do not claim the truth in the last instance, but the trifle below is covered by most of the reasons for the current problem. So that.

If you still have any sound, but it is bad or too quiet, I recommend that you familiarize yourself with this instead of this note:

1) poor sound in Bluetooth headphones: it is interrupted, there are delays, light hiss, etc.D.

2) how to increase the volume on the phone (Android). Too quiet sound

How to return the “missing” sound in headphones: what to pay attention to

The first recommendation is banal and simple. try to restart the phone and check the sound settings. Perhaps some kind of “quiet” mode in the parameters of the phone is turned on.

If you have wireless Bluetooth graters-keep in mind that sometimes they turn off (“fall asleep”). Try them to open./ON., so that they establish the connection again. In many cases it helps!

Besides. Look at the volume level directly in the application that your mp3 file reproduces, or radio, or something else.

If you have wired headphones. pay attention to the condition of the wire, especially near the plug

Very often in this place due to constant excesses-there is a break in copper veins, and contact becomes not stable. If you slightly move the wire (in this place). perhaps you will have a sound for a moment (then the reason is obvious) !

In any case, it is recommended to double.check the headphones on another (obviously serviceable) phone/PC/laptop.

Pay attention to the audio line, whether something has got into it? Often, dust, scruffy pieces of threads (from the in which you wear), and pr. trash.

To clean it, the following can be recommended:

  • Take the usual toothpick and wrap its end with cotton wool;
  • then moisten it in alcohol;
  • After that, carefully insert a toothpick into the audio connector and make several rotational movements;
  • As a rule, all dust and garbage settled on cotton wool. By the way, if after the first cleaning it was dirty. The procedure should be repeated.

On the upper panel, when connecting the plug from the headphones, the corresponding icon should light up. over, in 98% of cases, regardless of whether the headphones or wire themselves are working: the main thing is that the audio connector and the plug are in order.

If this does not happen, it is highly likely that the audio connector is faulty and it needs to be replaced.

If we are talking about wireless headphones, check if they are charged (usually when they turn on, the light indicator lights up).

By the way, new headphones always usually go discharged “to zero” (for security purposes).

To help!

One wireless headphone does not work, it stopped playing the sound. https: // ocomp.info/ne-rab-besprovodnoy-naushnik.HTML

Is the headset enabled. Pay attention to the indicator

When using a headset, which previously auto, has been gathered to another phone via Bluetooth, can lead to the fact that the mating function will be disconnected immediately after turning on the devices.

Try to run the conjugation manually: click the power button until the indicator begins to blink with blue-red color.

Check in the phone settings. Whether Bluetooth is turned on, and whether the headphones are visible in the list of connected devices (relevant for a wireless headset).

In general, I would recommend the following:

  • Remove Bluetooth from the list of devices: headphones, microphones, etc. gadgets that you previously connected to the phone;
  • After, turn off the work of Bluetooth in the phone settings;
  • Reload the device;
  • Then turn on the Bluetooth again and perform the association procedure with headphones.

Settings. Connection of the device. Bluetooth

music, headphones, hear

If you use adapters to connect headphones, pay close attention to them.

Not all of them are back-composed, and come up to all phone models. On the same Xiaomi, one often has to face the “chips” from the manufacturer, the devices of which are required by “native” adapters and adapters.

It will not be too superfluous to try to connect a deliberately serviceable headset to the phone (moreover, if you have previously stopped working, you should try wireless/and vice versa //-).

The main thing is to find out here: will the headset work with another integer work. If all “OK”. then it can stop on it. Well, you can order a headset for cheap in Chinese online stores, links below.

In case of infection of the phone with viruses, the appearance of critical systemic errors, glitches, etc. “Good”. it is worth trying to drop the device to factory settings (it is important: in this case, the contacts and files from the phone’s memory will be erased and removed. make them backup in advance).

To help!

How to reset Android settings to factory [Hard Reset] (T.e. Delete all data from the phone, tablet).

If you managed to somehow solve the issue differently. Let you know in the Комментарии и мнения владельцев (thank you in advance).

Reason 6

There is a slight probability that sound problems can be associated with a malfunction of the audio card (for example, it could “suffer” due to a jump in the mains, emergency opening. electricity, during lightning and t.D.).

In general, the fastest way to double-check this (and it is possible to solve the problem at all)-try to connect an external audio card to a laptop (PC). Fortunately, many of them are no more than the size of a flash drive! And I will tell you that even such a “small thing” can provide sound no worse than many built.in sound cards.

You can purchase such audio cards (as in my photo below) in ordinary computer. shops (in t.h. and on order). Issue price: ∼150-1000

If all of the above did not give results, I also recommend that you familiarize yourself with one of my long.standing note about “noise” (link below). This, of course, does not apply directly to the current problem, but still. A number of moments are crossed here and here, and perhaps those recommendations will be useful!

To help!

Hissing, noise, cracking and other extraneous sound in columns and headphones. how to find and eliminate the cause?

Why Windows transfers sounds to a microphone canal?

I noticed that the sounds from the system are broadcast into discord. Sinned that the microphone catches the sound of headphones, but.

physically turned off the microphone and this did not help at all

If you turn off the jack from the nest. The microphone will bend, so this is not some additional microphone:

So why does Winda broadcast sounds into a microphone canal and how to fight with it?

Windows can broadcast sounds all at once and in all places at the same time, if you have everything normal with adjustment in Windows itself, the stereomiksher is immutable or turned off, the sound does not physically fall into the microphone, the microphone is the one that your voice records, and noise reduction options are included and echoing (so that the sound from the speakers does not at all fall into the microphone from the word), the problem can really be in the retaining of sound flows in your sound driver, as a rule, this is realtek, the problem is often found on laptops, because there are built.in and speakers and speakers and speakers and speakers and speakers and speakers and speakers microphone. If you see the picture that I attached, then the entrance is “analog” and only one, right now there are headphones there, but not the essence, the percentage of the volume supplied from the system to the microphone is the same as when using headphones, which when using speakers and echo.delay, and sound quality It is far from similar to the quality of voice recording from a microphone or the quality of recording as if I had chopped the muzon on the phone and brought it to the built.in micro on the laptop, the quality when recording is very good as with a stereomiksher, then this is a systemic problem, because the sound goes to the microphone channel Right with Windows. The problem is solved very simply, we go to the realtek dispatcher, see our analog entrance, and directly pokes the mouse button on it and only then an additional menu of the nest settings will open and there we distribute that our analog’s nest is headphones, and not all at once, t.e. Your Realtekovsky driver does not understand what is micro and what there are headphones and serves micro to the headphones, and to the headphones of micro, t.e. The microphone channel also accepts systemic sounds and sounds from the microphone itself, and in the headphones we have to hear both music and suppressed microns (you never heard it, since you are quietly sitting mostly and the percentage of the supply volume to the channel is about 30%). T.e. We click on the realtek of the PKM on the nest and ask him what it is, I didn’t stand there on default, so everything was supplied to all the channels. I didn’t put in the last photo I put a checkmark that this is an analog’s nest now only headphones and now it is not cleaning, before this checkmark was not and the driver drove the fool, and because of this you had problems.

Damn, as I understand you. I bought SS Artic Raw and friends say that they hear literally everything that I look at YouTube, the reinstall of firewood has not saved (although you can dance with them differently). The most common answer about the stereo mixer. Of course it is turned off. Hundreds of reviews on the ears, no one complained about such

I found the answer in the program to jerk everything except the microphone in this way: https: // vb-audio.COM/Voicemeeter/Banana.HTM

but I want to understand what is wrong.

Oh, and you earned through the wax meter? Otherwise I still have noise in the war in the war. It is somehow necessary to specifically configure it?

And tried to remove the microphone and check if the noise will go? By the way, you also have headphones with an additional extension cord. I get the headphones from it, one cord with mom-jack remains. Symptoms do not go anywhere

How to eliminate problems

Often the problem is when a person hears himself in headphones associated with incorrect settings of the device. Eliminate such problems, you can strictly follow simple instructions:

  • On a computer or laptop, find sound settings options. To do this, you need to enter the “Control Panel” tab or use the entrance through the Start panel.
  • In it we find the “Sound” tab in the pop.up window and click 1 time with the mouse to enter.
  • The same action can be performed in another way by clicking on the right button once along the speaker icon on the main lower panel.
  • Initially, you need to find and click on the “Record” tab and find the microphone on which the signal comes out (there will be a check box near one of the devices on the list).
  • You need to click on the active device with the right mouse button and go to the Open Option option.
  • After that, you need to go to the “Listen” tab and carefully check if there is a mark on the option “Listen from this device” (circle, checkmark).
  • The situation when a person hears his own voice in headphones is possible if the checkbox is worth it near the parameter “listen from this device”. In this case, it is necessary to remove the mark and click the “Apply” button and be sure to “ok”.
  • After that, it will be necessary to perform the verification of the actions performed, to go to the “playback” tab, find the parameters of active speakers and connect.
  • Go to the parameters of the speakers “Properties” and find the “Levels” tab and carefully check that the active mark stands on “0” in the “Microphone” section.
  • It is also required to check the button on the right, which shows the speaker, it must be disconnected.
  • After that, press the “Apply” and “OK” button.

Such simple manipulations will eliminate the sound that the user hears from his own speech in headphones.

Many users, on the contrary, are looking for information on how to make their own voice in headphones to hear their own voice. This is easy, all actions are required to be carried out in the reverse order.

Sometimes, in order to eliminate the signal of your speech in headphones, it is necessary to check the accuracy of connecting headphones to the nest (they should be included in the red connector).

Reference! If the sound is heard on time online game, it is possible to make less amplification in Steam or software.

Applying the advice of experts to fix any problem with the computer is not difficult, it does not take much time.

How to avoid such problems subsequently

Is it easy to avoid such problems and malfunctions, what to do so as not to experience difficulties with sound?

To prevent malfunctions with sound, it is recommended to use only an official, proven driver. To do this, choose the point “Sound, game and video devices” in the menu of the control panel menu. Contact the context menu by pressing the right button and select an automatic update for the configuration of the selected equipment.

It is also worth systematically to check and diagnose the software component, namely sound drivers. Most often, difficulties with sound arise when the driver is outdated or faulty (damaged by viruses). You can update outdated drivers on the official portal of the manufacturer of the installed sound card. Do not resort to the use of third.party resources and unverified drivers so as not to aggravate the situation, do not bring malicious programs to the computer.

Attention! To be sure that there will be no such problems and the sound will be of high quality, it is recommended to buy and use high.quality headphones.

The reasons for the fact that there are no sounds with sound and the user hears himself in the headphones, they mainly consist in the technical problems of devices or illiterately installed programs, old or missing drivers. It is easy to cope with any of the problems if you strictly follow the recommendations of specialists and monitor the serviceability of the computer and all connected devices.