What to do if your iPad won’t charge

Efficient ways to fix your iPad won’t charge or charge slowly

You are facing a situation, iPad is not charging or charging slowly? In fact, iPad not charging is unfortunately one of the common problems for Apple users.

Your iPad may not charge for a variety of reasons. It could be a problem with any of four iPad components, including the charger, cable, charging port, and software.

This post shows 7 effective ways to fix iPad not charging or charging slowly, We’ll help you figure out if the plug, cable or lightning port (or USB-C) is faulty, and how to fix iPad charging problems in detail. If you plug in your iPad to charge, but the screen stays completely black or gives out Not charging, you can try these methods to solve the problem.

FoneLab allows you to put your iPhone / iPad / iPod out of DFU mode, recovery mode, Apple logo, headphone mode, etc. Д. In a normal state without loss of data.

• Fix disconnected iOS system problems.
• Extract data from disconnected iOS devices without losing data.
• It’s safe and easy to use.

iPad not charging

And get the best deals from trusted technicians.

• Compare and choose the best deal
• Feedback only from interested professionals
• Do not waste time dealing with intermediaries

There are many factors that can cause your iPad not to charge. Most often, the technique refuses to charge from a third-party charger, from a computer (desktop or laptop) of another company. Also the problem may lie in something else:

• Mechanical damage to the iPad or the connector
• Moisture in the case and other factors associated with improper use of the device

Some malfunctions that cause the devices to charge poorly can be dealt with by yourself. Complex faults should be entrusted to professionals. But before you take the device to the service center, try to solve the problem by following these simple instructions.

To find out why the iPad writes “no charge”, you must first pay attention to:

• Defective ports: very often ports are broken because of careless handling of the device or after mechanical damage due to improper transportation of the device. The best solution in this situation will be to go to a specialized workshop;
• Possible failure of the charger: to check it, it is better to try for a while to use another charger, if the problem does not disappear. you need to look for another cause;
• Probably a failed lower loop: mainly such a malfunction appears due to ingress of liquid into the device;
• Power controller: it mostly breaks down as a result of using a non-original charger;
• If the device board gets wet: the best solution would be to send the device to a service center for board cleaning.

Troubleshooting by yourself

After finding out why your iPad says “no charging”, you can begin the process of fixing the problem. The procedure will be as follows:

• The first thing to try is to connect the USB cable to all the free ports on your PC. It is important to find out which USB ports are on the computer (usually USB 1.0, 2.0 or 3.0). USB 3 only.0 provides up to 900mA, and the first two provide up to 500mA. Respectively, the charging time will depend on the port the device is plugged into.
• Buy a double USB adapter, which will allow you to use twice as much energy for charging.
• Installation of the appropriate utility on PC. Ai Charger, AppCharger, etc. The main benefit of these applications is to put the port into a higher power mode. But it is very important to know the exact model of the motherboard on your computer so you can download a suitable utility from the manufacturer’s website.

Causes of problems with recharging iPhone or iPad

Faulty cable and/or charger

USB cables manufactured by Apple, despite the confidence Apple itself inspires in its gadgets and PCs, Apple’s weakness. They wear out quickly in a year or two with heavy use. This encourages a person to buy a USB cable made by third-party Chinese firms.

Not certified (not original) charging cord

It is easy to distinguish a fake “charger” from the original. Signs of counterfeiting:

• Misspellings and typos in small print, illegible characters and logos, bad or illegible font.
• Uneven matting of the case.
• Irregularities in the characteristic joints, seams, the convergence of parts of the case, USB-socket, the location of the pins of the mains plug.
• Poor quality plastic, characteristic “toxic” smell, creaking.
• Mismatch between output voltage and charging current to Apple’s requirements for a particular gadget.

There are cases when the “homemade” “charger” burns out from overvoltage in the network or systematic overloading, sometimes taking with it the life of your gadget. Do not skimp on a branded charger.

Faulty outlet

Everything is clear. replace or repair the socket, check the wiring in this area, restore the mains voltage.

Your gadget socket is defective or clogged

Not only dust but also small debris accumulates in the connector opening. Remove particles interfering with the connection of the corresponding plug. If the plug is broken, it can only be replaced. contact the service center.

How To Fix An iPad That Won’t Charge-Easy Tutorial

Device not charging. iPhone or iPad software failure

It happens rarely, but it’s possible if you, for example, are fond of “jailbreaking” Apple devices and generally by yourself get into the programming code of your gadget and do whatever you want in the system folders of your iPhone or iPad. Apple is trying its best to protect over-zealous users from “gray” manipulation of iOS operating system. You can reflash your device from PC to iTunes yourself if the gadget is charged while turned off. otherwise you can’t do without specialists.

A weak power source, which is not capable of charging at the required level

There may be cases where the charger is not designed for the load given by your gadget. for example, you managed to “charge” from the iPhone to charge the iPad, which requires a significantly higher current charge, the benefit here helps detachable from the charger USB-cables. And although Apple puts in their “chargers” normal protection against this encroachment, it often happens that the iPad will not charge from not “his” charger. or will not charge for 2, but 4-5 hours.

If the charger is so weak that it only charges when the iPhone or iPad is turned off or in “sleep” mode. urgently replace it. The same applies to external batteries, combined power sources like PowerBank with a solar panel, mechanical “chargers”, etc. д.

Faulty internal power nodes in your iPad or iPhone

Here you can’t do without the specialists of the iStore (there is one in every major city). You can replace defective components (for example, the recharge controller) with the exact same ones. For example, if iPhone 4s is faulty, you should replace its “native” components with identical ones.

Worn out battery

Apple is doing its best to make you change your gadget less often. it’s just hiding it under aggressive advertising of new iPhone, iPad and AppleTV models. The company has been “managing” each model for years, releasing iOS updates for it even for devices that are 5 or more years old. Here is a paradoxical situation: you are more likely to wait for the battery to fail, than to replace your iPhone 4s with the iPhone 7. And here you can’t do without experts. and here’s why.

• In the iPhone or iPad, the internal components, including the battery, are sealed. there is no need to break this seal yourself.
• Unlike most Android-smartphones, where the back cover can be easily removed in 10 seconds, the back cover is fixed by very small screws, which can only be unscrewed with a special screwdriver, and has special locks.
• The battery “sits” on a special loop, which is difficult to remove with improvised tools.

In general, Apple is a firm that protects its users of gadgets from unauthorized interference. Apple smartphones and tablets are very reliable and are made primarily for ease and convenience, not for the people’s amateurishness. Contact an Apple Service Center for battery replacement.

Charging your iPhone or iPad in a case

In general, to cover with something or stick your gadget in a case. is utopia! While charging your iPhone or iPad heats up to 40 degrees. and if the heat does not go out, it will be heated further, and the extra heat leads to accelerated battery capacity degradation. Take the case off your iPhone or iPad when charging, even when you are in a cold room!

Overcooling or overheating iPhone or iPad

But it is recommended to use the Apple gadgets in the cold in a case. Subcooled battery does not hold the load current when filming videos, downloading/downloading large files, using Google maps, playing online games, etc. д. Exposing your device to frequent cold stress is not recommended: it loses battery capacity and wears out faster. In freezing temperatures, even a new, fully charged iPhone will shut down in 8-10 minutes. “Racing your gadget around in freezing temperatures for hours is like driving it through the hot summer sun: no modern battery is capable of giving up all the energy you have left in it at extreme temperatures. And any temperature outside 10-40 degrees is extreme for the lithium-ion battery found in all Apple devices. If the charge level of your iPhone or iPad drops suddenly. move your device away.

The main causes of problems

Failures in the charging iPad can occur due to a variety of factors. The malfunction is caused by falls, bumps, illiterate reflashing and other violations of the rules for using the gadget:

• connection of the charger of another company (error messages will appear on the screen)
• Connecting the charger to a bad socket
• Connecting the tablet to a computer or laptop of another brand or outdated model of gadget
• The power controller or charger connector is damaged
• battery or lower cord failure
• Moisture in the gadget case, USB port or on the battery

Additionally, there are situations in which the iPad is only fully charged when switched on. this also indicates the presence of malfunction. On what kind of failure has occurred in the gadget, depends on the choice of methods of its repair and the duration of recovery.

Why won’t it charge. Possible problems

The most likely reasons why your iPhone doesn‘t charge when it’s plugged in are problems with the charger or cable. It can also be a software update bug.

Dirt on the Lightning port, or oxidation of the contacts can be the reason why the charging process does not begin. The problem is also caused by a dead battery.

It happens that the iPhone, on the contrary, charges, but does not turn on. About this it is written in detail in the article:

It’s time to change the battery

This is another reason why iPad stops charging. If your device is more than two or three years old, the battery has probably given up its service life and it is time to replace it. Usually this is preceded by increasingly shorter operation time without recharging.

In addition, frequent and strong temperature fluctuations, prolonged exposure to extreme cold or, conversely, to the heat can “kill” the battery. It is possible gradual capacity drop or instantaneous “death”.

A trivial defect in the controller or its failure during improper use is not excluded.

In order to find out what is the condition of the battery, and whether the problem is really in it, it is necessary to disassemble the iPad. It is important to have the appropriate knowledge and tools. If you have it all. go for it, but in this case you lose warranty service. If there is no knowledge or not enough, it is better to apply to the store where you bought your tablet PC, or in the service center, which has a certificate for repairing Apple products.

For this reason we do not give in the article instructions for replacing the battery in the tablet. A specialist will find the information on their own, and it is better not to provoke a non-specialist by typing here “step-by-step instructions to go into orbit”.

The Lightning port (or 30-pin classic connector on iPad 3 and older models) is always open for air and fine dust particles. This leaves it vulnerable to soon-to-be contaminated connections. Dirt ingress leads to broken contacts and disruption of the charging process. the cable is always moving, twisting, bending. Clean the iPad connector first if it stops charging.

If you’re trying to figure out why your iPad isn’t charging, try connecting it to your computer (or Mac), which may cause the battery to fill more slowly or even cause the message “No battery” to appear in the status bar at the top of your screen. But there should be a reaction to the connection in any case.

To see if the iPad is charging, look at how the battery icon is displayed, it should show lightning.

No? Then we move on to a list of the main causes:

• Problem with the wire.
• Adapter is faulty or there is a problem with the outlet.
• Moisture ingress or mechanical damage.
• Power controller breakage.
• Clogged Port.

Now let’s look at all these factors in detail.

A wire problem

First of all check your USB cable. Is there any damage? There should be no broken or bent pins. Important: Your cable must be either original or MFI (Made for iDevices) certified. There should be a sign like this on the package that your cord was in:

The problem is with the adapter or the socket

The problem may be with a faulty adapter or outlet. For this reason once I have stopped charging my iPad. In this case the advice is simple: check the adapter and the socket to work with other devices, if necessary. replace.

Moisture and mechanical damage

One of the reasons your iPad doesn’t charge may be because it’s wet. In this case I advise to take the “sick” to the professionals, because if you do something wrong, it will only destroy your device.

Mechanical damage is not uncommon on iPads, you only drop it once. It is not even worth asking what to do if after that the iPad does not charge, of course, go to the service.

The problem with the controller

When you charge the tablet long enough with a non-certified cable, the power controller can break. If your iPad is still under warranty, consider yourself lucky. Otherwise, you’ll have to pay a lot of money for repairs.