There is no paper printer how to fix it. What to do if the printer lit paper

The printer lit paper and stopped printing

Before starting a conversation about one of the most common breakdowns (the printer lights the paper), we will figure out what this device is. So. The printer is a device of an external (separate) location from a computer designed to withdraw coded digital information from computer files with its conversion into text form and printing on paper.

In its relatively short history, the printer has passed many evolutionary changes, which, starting from the first sample of this device, there is no sense in.

Let’s call only devices that are used today:

Malfunctions

Like any high.tech device, printers are subject to faults. The level of complexity of the breakdown directly depends on the operating conditions of the device.

Conventionally, they can be divided into two groups:

• To bring the device in the proper working condition, the intervention of a specialist of the service center (Canon, HP, etc.e).
• The malfunction can be eliminated with your own hands.

The second group (the so.called domestic breakdowns) includes mainly problems with the quality of the print and with the lack of a paper sheet through the device. In other words, the printer HP (Canon) lights the paper. In any case, both misunderstandings can hardly be called malfunctions. They should rather be attributed to the incorrect use of the device, the absence of preventive care and the use of poor.quality or inappropriate consumables for this model.

Consider the problem on the example of lighting paper by a Canon printer.

How to fix the error “There is no paper in the printer

First check the general condition of the paper loaded into the printer. Replace any paper that can be torn, wet or bent. In addition, make sure that all the paper is the same type and length. Paper stack should not contain more than 25 sheets. Click on a stack of paper on a flat surface to level the edges of the sheet, and then place the stack back in the tray for printing.

The panel on the rear panel of the printer may not be installed completely. Turn the printer and make sure the back panel is in place. If this is not the case, perhaps the paper is stuck there. Remove the back panel completely. Then you can remove any crumpled paper and install the rear panel back on the printer.

Solution 3. reboot the printer

The discharge of the printer can help. First disconnect the power cable without turning off the printer. Then you should wait about half a minute before connecting the power cable to the printer again. If the printer does not turn on automatically, press the power button.

The accumulation of dirt in printer rollers can lead to paper supply errors. Thus, cleansing rollers is a potential solution to the problem. You can clean the videos as follows.

• First turn off the printer and disconnect the power cable.
• Take a bottomless fabric and water in bottles for cleaning rollers, but do not use tap water or alcohol.
• Usually you can access the selecting rollers in front by removing the main paper tray. However, some printers also have a rear access door with which you get access to the rollers.
• Then wipe the rollers with fabric and turn them up your fingers. Clean the videos of the duplex of your printer if it has a duplex.
• Leave the videos to dry for about half an hour. Then connect the printer power cable again and, if necessary, turn on the printer again.

In order not to encounter a malfunction of sheets and autopods, use sheets of recommended quality and density, without exceeding them and without using low.quality raw materials. In this case, wear increases, which leads to a reduction in the service life.

With problems of stretching sheets, try to take greater density, while avoid coated varieties, and opt for Finnish offset. Good quality printing sheets are available in stores.

Shutdown of the manual feed mode

If there is no paper in the printer, although it really is, then try to turn off the mode responsible for manual. First you need to make sure that the printer is in the state. Then, through the “Start” menu, open the “Devices and Printers” section. Select the desired Daves and open its properties using a click on its icon with the right button. Next, go to the “Print Settings” and, choosing “Source”, click on the “Auto Electo” item. Save the amendment and try to print the document from the program from which you tried to print it last time.

Perhaps the source of the problem is incorrectly set settings in the print driver. Although the probability of this reason is very low, but still should not exclude it. To see the settings and, if necessary, change them, open any document designed to print, and then call the print window. for this, just press the Ctrlp key combination. Select the desired device in the window that appears and go into its properties. Find on a tab called “functions” from the corresponding drop.down menu “size” and “type of paper”. Change the parameters for a specific print version, save the changes and print the document.

• Another reason not remarks by a printer of paper can be broken flags of optical sensors. This situation is often found on laser printers where this type of sensors are used.

First of all, in order to understand who is to blame for the computer computer or All-in-One Printer-try to make a copy or print a test sheet. If the seal passes successfully, then most likely the problem is not in the printer.

If the described methods do not help, then contact the center that specializes in the diagnosis, repair and maintenance of office equipment. If they don’t help you there, then you have only one thing left. buy a new device.

What to do if the printer does not see the paper?

Initially, when the dialog box appears in the computer with a warning about the absence of paper, the corresponding compartment should be checked. Usually, at high printing pace and large volumes of the document, users forget to replenish the supply of sheets in time, so there is a hitch when printing documents. This problem is easy to eliminate, it is enough just to replenish the supply in time and monitor the condition of the sheets in the compartment. But if the printer writes that there is no paper in the tray, but it is there, then you need to look for a problem in another.

If nothing has changed after replenishment, try to restart the system. To do this, turn off the equipment and after a few minutes re.connect the equipment to the network. Modern models are equipped with a system of automatic diagnosis and elimination of problems that are activated when re.connecting.

Important: these actions can eliminate the cause in most cases, but there are situations when the problem is as a paper medium and the system settings.

How to solve a problem

If the usual actions described in the instructions did not help to eliminate the problem, it is worth identifying the reason for the termination of the printer. So why the printer does not see the paper? For convenience, we present a list of the most common problems and ways to solve them:

• Wear a video for capturing paper, which conducts one sheet for applying a fingerprint. Try to manually push the sheet when performing a sheet. If you succeed, then the reason is found. In this case, fix the video or replace it with a new part.
• Strong holding of limiting holders in the sheet supply compartment, try to loosen them or completely remove them.
• Too much volume of loaded pack of paper, remove the excess part.
• Poor quality of paper media, very low or high density of the material. For diagnosis, print the page using cardboard. This can restore work.
• Fucking excess dust on the print head and paper presentation. To solve the problem, clean the device, delete foreign elements.
• Perhaps the problem consists in the junction of the previous sheet sent to the printout. Inspect the case and internal details, if there is a jammed area, carefully remove it.

In most of the described situations, you can independently restore the workflow to continue printing documents. If you doubt the correctness of manipulations, you should contact the service center for diagnosis. Keep a guarantee, for it they will be able to provide free help or replace the device.

Important: For the use of the warranty coupon, do not carry out independent repair and replacement of parts, otherwise it will be invalid.

Action in case of error

In order to find out the reason why the printer writes a trim of paper, and a small diagnosis has occurred. The self.test report will identify a group of the most common problems associated with error and check the technical condition of the device.

• Run the device by pressing the power button.
• Load a pile of white clean paper into a standard format tray, then level the axial guides in width.
• All this time to hold the power button in the on position.
• Now, during the pressed button, do the manipulation of opening and closing the cover of the cartridge department 4 times.
• After turning off the power button, a report with a self.check will be released.

Important! It is advisable to receive a report after each attempt to solve the problem when the printer writes “paper stuck”.

Solution of problems

Knocking settings in the system

In some cases, if the printer writes a junction of paper, although there is no jamming, then a standard operation to reject the mood base comes to the rescue. But for this it is necessary to perform a number of established actions.

Khuling the settings database using disconnecting from power

• Run the device with a power on.
• Without disconnecting, remove the cable from the power connector on the back.
• Make sure that the cable is not connected to the outlet.
• Waiting time of at least 15 seconds.
• Connect the cable back with an electric outlet.
• Insert the reverse end into the nest on the device.
• If automatic inclusion did not work, then start the car manually.

View verification report

If the report of the report was successful, then re.start the printout of the source document. In case of successful completion of the process, nothing should be done further.

If the printer does not print and writes there is no paper and the report is not printed, then you can proceed to the next stage of verification.

Check the characteristics of the paper

The reason why the printer writes is no paper, may be dirty, crushed, deformed or not formatted paper. The properties of paper are directly reflected in the quality of the print and the speed of capture of the sheets. So that nothing is stuck in the system, it is desirable to use the paper of these characteristics.

To study the condition of the sheets

• Extract all the paper sheets from the tray, especially those that are stuck in case of unsuccessful printing.
• Check the stack is not the presence of obstacles to the capture of the paper with videos. Carefully check the input hole for the presence of foreign objects. Even the presence of minor garbage and paper shreds can slow down the paper feed.
• If sheets of indecent species, that is, crumpled, twisted, torn, immediately replace.
• Make sure that the parameters of all sheets in the stack do not differ. The device is able to function correctly only in the presence of paper of the same type.
• Align along the edges on a smooth surface.
• Check the permissible amount of paper in the stack.

Repeated paper load

• It is necessary to push the axial alignor of the paper.
• Then gently place the stack in the tray to the limit.
• Pushing the guide leiper to the stop.

When successfully printing the report, the launch of the document and the absence of jam into the process do not take further actions.

When the problem is not eliminated and the device does not print, it is necessary to start the next stage.

Cleaning rollers

Why the printer does not print, and there is a junction of paper and what to do at the same time. Dust and dirt accumulating on the surface of rubber rollers can cause this.

Clean the rollers on paper supply

• Run the device, turn on the power button.
• Turn the printer to ensure better access to the back side.
• Remove the power cable from the connector on the back panel.
• Using fixers holding the back door to remove it.
• Check the paper for integrity. For a more attentive inspection, you can use the flashlight. If paper shreds are detected, remove.
• Wipe the videos only with a rag without villi moistened in clean water. For access to the surface, you can carefully crank the rollers.
• Find a video on the seizure of paper in the depths.
• Carefully cleanse the video with a tampon moistened in distilled water.
• Make sure the integrity of the surface of the rollers and the absence of cracks or shifts.
• Wait for complete drying.
• Insert the door back.
• Connect the device to power again.

If there is a report, the document is tested for printing.

If there is a report, but the absence of the process of printing a document, go to the next stage of verification.

If the report is not printed, then repeat the attempt, while listening to the work of the capture mechanism. After starting the process of printing the report, gently pushing the paper to the rollers.

If then it is not possible to display the report, then you should repeat the actions to clean the rollers.

If the forced pushing has worked, then you can try to launch the seal of the source document.

Когда повторная прочистка роликов не помогла и есть замятие, следует перейти к следующему этапу решения проблемы.

Change the requirements for the paper in the driver

What to do if the device gives an error “no paper”, even if nothing is stuck, and refuse to grab sheets of paper. Set appropriate settings in the print driver. Such functionality eliminates the overrun of the materials, in the case when the paper of the non.corresponding sample was used.

When none of the options presented helped, you should contact the service center. Masters will be able to find a serious problem faster and safer and eliminate the malfunction in the shortest possible time.

Когда принтер или all-in-one printer не могут захватить лист бумаги, появляется ошибка типа «нет бумаги» и печать останавливается. To establish the cause of the problem and eliminate it. you should sequentially check the possible options.

Action in case of error

In order to find out the reason why the printer writes a trim of paper, and a small diagnosis has occurred. The self.test report will identify a group of the most common problems associated with error and check the technical condition of the device.

• Run the device by pressing the power button.
• Load a pile of white clean paper into a standard format tray, then level the axial guides in width.
• All this time to hold the power button in the on position.
• Now, during the pressed button, do the manipulation of opening and closing the cover of the cartridge department 4 times.
• After turning off the power button, a report with a self.check will be released.

Important! It is advisable to receive a report after each attempt to solve the problem when the printer writes “paper stuck”.

Solution of problems

Knocking settings in the system

In some cases, if the printer writes a junction of paper, although there is no jamming, then a standard operation to reject the mood base comes to the rescue. But for this it is necessary to perform a number of established actions.

Khuling the settings database using disconnecting from power

• Run the device with a power on.
• Without disconnecting, remove the cable from the power connector on the back.
• Make sure that the cable is not connected to the outlet.
• Waiting time of at least 15 seconds.
• Connect the cable back with an electric outlet.
• Insert the reverse end into the nest on the device.
• If automatic inclusion did not work, then start the car manually.

View verification report

If the report of the report was successful, then re.start the printout of the source document. In case of successful completion of the process, nothing should be done further.

If the printer does not print and writes there is no paper and the report is not printed, then you can proceed to the next stage of verification.

Check the characteristics of the paper

The reason why the printer writes is no paper, may be dirty, crushed, deformed or not formatted paper. The properties of paper are directly reflected in the quality of the print and the speed of capture of the sheets. So that nothing is stuck in the system, it is desirable to use the paper of these characteristics.

To study the condition of the sheets

• Extract all the paper sheets from the tray, especially those that are stuck in case of unsuccessful printing.
• Check the stack is not the presence of obstacles to the capture of the paper with videos. Carefully check the input hole for the presence of foreign objects. Even the presence of minor garbage and paper shreds can slow down the paper feed.
• If sheets of indecent species, that is, crumpled, twisted, torn, immediately replace.
• Make sure that the parameters of all sheets in the stack do not differ. The device is able to function correctly only in the presence of paper of the same type.
• Align along the edges on a smooth surface.
• Check the permissible amount of paper in the stack.

Repeated paper load

• It is necessary to push the axial alignor of the paper.
• Then gently place the stack in the tray to the limit.
• Pushing the guide leiper to the stop.

When successfully printing the report, the launch of the document and the absence of jam into the process do not take further actions.

When the problem is not eliminated and the device does not print, it is necessary to start the next stage.

Cleaning rollers

Why the printer does not print, and there is a junction of paper and what to do at the same time. Dust and dirt accumulating on the surface of rubber rollers can cause this.

Clean the rollers on paper supply

• Run the device, turn on the power button.
• Turn the printer to ensure better access to the back side.
• Remove the power cable from the connector on the back panel.
• Using fixers holding the back door to remove it.
• Check the paper for integrity. For a more attentive inspection, you can use the flashlight. If paper shreds are detected, remove.
• Wipe the videos only with a rag without villi moistened in clean water. For access to the surface, you can carefully crank the rollers.
• Find a video on the seizure of paper in the depths.
• Carefully cleanse the video with a tampon moistened in distilled water.
• Make sure the integrity of the surface of the rollers and the absence of cracks or shifts.
• Wait for complete drying.
• Insert the door back.
• Connect the device to power again.

If there is a report, the document is tested for printing.

If there is a report, but the absence of the process of printing a document, go to the next stage of verification.

If the report is not printed, then repeat the attempt, while listening to the work of the capture mechanism. After starting the process of printing the report, gently pushing the paper to the rollers.

If then it is not possible to display the report, then you should repeat the actions to clean the rollers.

If the forced pushing has worked, then you can try to launch the seal of the source document.

Когда повторная прочистка роликов не помогла и есть замятие, следует перейти к следующему этапу решения проблемы.

Change the requirements for the paper in the driver

What to do if the device gives an error “no paper”, even if nothing is stuck, and refuse to grab sheets of paper. Set appropriate settings in the print driver. Such functionality eliminates the overrun of the materials, in the case when the paper of the non.corresponding sample was used.

When none of the options presented helped, you should contact the service center. Masters will be able to find a serious problem faster and safer and eliminate the malfunction in the shortest possible time.

What to do if the printer does not capture paper

We constantly have to work with various information and documents in electronic form, but the need to duplicate them in the printed version does not cease to be relevant. In addition, thanks to modern technologies, you can independently print family photos, design projects, business cards and even large posters. Not everyone can carefully read the rules of operation of a particular device, which sometimes leads to a number of issues, which, upon closer examination, it is quite possible to solve it independently. One of the most common. the printer is turned on and works, but cannot capture the next sheet for printing.

There may be several reasons why the printer does not take the paper:

• Inside the printer, between printing heads or in the very tray for capture of paper, a foreign object restricts the movement of the mechanism. This situation is most likely if the device is located on the desktop, above which there are shelves with stationery. Paper clip, a cap from a handle, an eraser Even a fragment of an inaccurate sheet can cause a malfunction in work.
• Incorrectly selected paper. Some of its species have insufficient or excessive density, which means that the printer simply cannot capture the sheet.
• Paper capture rollers are polluted or begin to deviate from the working algorithm. This reason can also be eliminated independently.
• Even if the paper is selected correctly, the device may not cope with it due to deep creases, irregularities or the wrong sheet sizes.
• Drawing failures for equipment. In this case, you have to diagnose both the printer and the computer.

What to do if the printer does not capture paper

Do not rush to call the master or restart the device. Most likely, you will be able to eliminate the problem yourself. Inspect the printer and, if possible, its internal mechanisms, check the connection with the network and the computer or laptop. Do not use physical strength or try to disassemble the printer yourself, because this is a rather complicated device.

Check the paper

Learn the characteristics of your device, paying attention to the permissible paper density. Before the seal, it is worth thoroughly smoothing the sheets and check if there are no bent corners. Also ensure a flat location of the sheets relative to the edges of the paper supply tray.

IMPORTANT! Special limiters are installed on some of the devices that do not allow the sheets to shift or hesitate. If your device is not equipped in this way, try to hold the paper yourself during printing, directing it for a more even and clear printing.

We drop the settings

Sometimes hardware or software fails. You can drop the current print settings, which is very simple:

• Clean the queue for printing documents in order to convert the device into waiting mode.
• Without turning off the printer, turn it off from the power supply and leave it somewhere for half a minute.
• Connect the device to the network again. In this case, it should turn on independently, but without previous settings. If this does not happen, turn on the printer manually using the start button.
• Carry out test printing. If the problem was a software failure, you will not have new difficulties.

We delete extraneous objects

You can use tweezers if you remove the extraneous item with your fingers is inconvenient. Act unhurriedly and carefully in order not to damage the device. If a sheet is stuck in the printer, pull in different directions in order to understand what exactly the piece caught on.

We clean the videos

Most often the cause of roller pollution is low.quality paper and ink. Paper fibers settled on rollers, as well as the remains of ink, thereby reducing their ability to capture and move the sheet when printing. If the printer is old, instead of cleaning it will be much more rational to replace the videos with new. If you print something urgently, it is enough to make a couple of turns on the worn rollers with island.

You will need: to clean the videos suitable for the work:

It is necessary to moisten the fabric and gently wipe the videos until all the dye comes off from them. To clean hard.to.reach places, you can use wet cotton wool sticks. If you are confident in your abilities, you can try to extract videos for a more thorough cleaning. Each model or company has its own algorithm for this procedure, which should be studied in advance.

We change the settings of the drivers

Sometimes the seal does not occur due to incorrectly configured drivers for the printer, in particular, incorrectly indicated size and type of paper. In order to eliminate this problem, it is necessary to manually set the necessary indicators, which is not particularly difficult.

You need to call the print menu, choose the printer you need and move on to its properties. Next, open the tab with the functions of the printer and set the paper characteristics in accordance with the data specified on its packaging. Or choose the closest option to them from the proposed system. Next, you need to save changes and try to print.

If this procedure has not helped, it may be worth reinstalling the driver. To do this, you need to delete the previous versions using the device dispatcher. After that, you can download new security that is suitable for your printing device and install it on a computer.

We delete extraneous objects

If the device stopped taking paper or it does it very badly, then certainly an extraneous object that violated its performance came inside it. To eliminate the reason, first of all, you need to do the following: turn off the printer from the power and remove all the sheets from the feed tray, and if possible to completely remove it. If your printer is laser, then after taking out its consumables, open all the covers you can to check if there are any extra items, for example, pieces of paper. Collect the printer in the reverse order and fill it with the tray with 10-25 sheets of paper, then make a test print.

The driver settings have changed

Often the mechanism of the printing device begins to stop taking paper due to the changed settings in the print driver. In such a situation, the corresponding question arises: what to do if the printer refuses to take paper due to settings? To solve the problem, open any document that can be printed and press hot keys to cause a printing window. Select the right device in it and open its properties. Next, go to the “Functions” tab, where from the drop.down menu, select the optimal type of paper and its size. Do not forget to save the changes made, then try to make a trial print. If this does not help, then it is better to call the master or take your printer to any reliable service center yourself.

It happens that the exciting sheets of the mechanism began to junk due to the paper supply of paper polluted during operation. To carefully clean this part you need to prepare any clean material without villi, water and several cotton sticks. over, it is better to use the water to be filtered or distilled. Remember that alcohol and other cleaning products should not be used for this procedure.

If the rollers are located in fairly easy availability, then carefully wipe them with material, previously moistened in water. Otherwise, you will have to use a cotton wool that you need to moisten and squeeze well. Then you need to assemble the device, turn it on and print a few of any documents.

If this recommendation does not help you, then most likely, the filing rollers require replacement. To do this, you can contact the Office repair center or read information on the model of your printer on our website and independently replace. The second option, of course, is the most economical.