Samsung S821 Error Codes
Preparing the machine for work
Washing machine Samsung Bio Compact S821 is designed to be the ideal home assistant that will quickly put your dirty things in order. However, you need to learn how to use it correctly and, of course, the machine must be correctly installed.
After unpacking and inspecting the Samsung machine for defects and various damages, unscrew the shipping bolts that can be found on the back of the case. Next, you need to select the installation location. Strictly speaking, you need to choose a place in advance, even before buying a car. Organize communications, strengthen the floor and move the furniture so that it does not touch the body of a working washing machine.
If all this is done, you can start connecting the “home assistant”. About installing and connecting a washing machine with your own hands, read the article of the same name. But we will still describe some additional installation tips in this publication.
- Try to align the body of the machine as best as possible, twisting its legs alternately with a wrench.
- When screwing on the inlet hose, do not forget to put the rubber O-rings, if they become stiff from long-term storage, soak them in engine oil.
- If the inlet hose is too short, you can additionally purchase a longer hose and replace it with the standard one. We do not recommend extending the standard hose.
- When connecting the drain hose to a siphon or sewer pipe, be sure to seal and secure the connection with a hose clamp. When draining, the pump creates enough pressure so that water splashes out through the loose connection to the floor.
- The drain hose does not need to be connected anywhere, but simply hooked over the edge of the sink or thrown into the bathtub, but it will not look aesthetically pleasing.
- To connect the washing machine, you need a separate outlet, the power of which will provide a wire of sufficient cross-section, preferably copper. The socket must be moisture resistant. If you often have power outages, connect the stabilizer to the outlet, and the washing machine to it.
Control panel: button assignments
After connecting the Samsung Bio Compact S821 washing machine, do not rush to start washing. First, familiarize yourself with the capabilities of the technology by examining the control panel and the purpose of the buttons and other elements that are located on it. Let’s describe them and give examples of how they can be used.
- Powder receptacle or powder dispenser. A very important element that is located to the left of the control panel. We pour powder into it, pour conditioner and bleach.
- Indicator panel. Takes up the lion’s share of the control panel of the Samsung Bio Compact typewriter. These are different bulbs, each of which has its own purpose. They convey important information about the course of washing, rinsing, spinning. They can even indicate to the user that the car has broken, but we hope it won’t come to that.
- Program selection button. This button (the first from the powder receptacle) is very important. With its help, you can scroll through the wash programs until the one you need is selected. You can experiment, press the “program selection” button several times and look at the indicator panel, the light should be on opposite the mode you have chosen. Cotton, synthetics, thin fabric, etc.
- Button “temperature selection” (second from the powder receiver). Its purpose speaks for itself, because this button helps to adjust the temperature.
- Drum RPM button (third from the powder cuvette). This button will help you set the spin speed. You can choose to wash without spinning, at 600 rpm and 800 rpm.
- Start / stop button (fourth from the cuvette, large with illumination). An important button, because you have to press it every time to start the washing program. She is pressed to stop washing.
- On / Off button (located on the right edge). The default button, you guessed it.
It is very easy to deal with the Russified control panel, because all the buttons and lights are signed on it. But if your car is from Europe, the panel can also be in English, German, Polish or any other language. In this case, the instruction will come in handy.
Washing and managing it
So, we have carefully examined the control panel, you can start the first wash. According to the instructions, the first wash is carried out without linen in order to rinse the insides of the “home assistant”.
- You must first turn on the machine, then open the powder receptacle to put a small amount of detergent in its leftmost compartment.
- Open all taps that shut off the water supply to the washer.
- Set the temperature selection button to 40 0 С.
- We press start and wait for the end of the program.
Now a few words about loading detergent. In the future, you will use a variety of washing programs, and each will have its own characteristics. These features will also concern the placement of detergents inside the powder receptacle. Please note that for the prewash you need the far right compartment, the softener needs to be poured into the middle compartment, and the leftmost compartment will be used more often, because it is for the main wash. Consider an example of a daily wash.
- Turn on the machine and open the door wider.
- We put the linen inside one piece at a time. Dirty laundry should not be lumped in and, of course, it must be sorted out before washing.
- We close the door until a characteristic click.
- Putting detergent and conditioner in the powder receptacle.
- Select the program, temperature and spin speed with the appropriate buttons. If it is impossible to choose something, then the program does not provide for this ratio of parameters.
- We start washing by pressing “start / stop”.
Manual for washing machine (S821) Samsung Bio Compact
For the Samsung Bio Compact S821 washing machine, the instructions are quite easy. Even if you have lost the printed version of the instructions that came with your “home assistant”, you can always visit our site and download both the original and the compressed version of this document. In this publication, we just present a condensed, adapted version, which you will definitely like, because you will have to read very little.
How to properly maintain a typewriter?
Good owners always keep an eye on any household appliances, all the more so for a washing machine, because in a modern house without an automatic washing machine, it’s “like no hands.” Samsung Bio Compact S821 does not require special care, in any case, what needs to be done every time will hardly make it difficult for you. But if you forget about the elementary rules of care, then this can affect the operation of the washing machine in the future, and affect negatively. What rules are we talking about?
- Samsung washing machine should dry after each wash. Wipe the sunroof seal and other wet parts with a rag. Leave the hatch and powder drawer ajar to allow moisture to evaporate and prevent fungus growth.
- If water or detergent gets on the control panel, wipe it immediately with a dry cloth. Excess moisture is very harmful to electronics.
- The dust filter should be cleaned a couple of times a year. Its location is shown in the figure below. Unscrew the filter plug, drain the stagnant water, and then clean out all the dirt from there.
- Once a year it is necessary to clean the flow filter of the inlet hose, which is located at the junction of the inlet hose with the washer body. This is done like this: we shut off the water, unscrew the inlet hose, pull out and wash the filter with pliers, put everything in place.
- It is also sometimes necessary to inspect the inlet hose. If cracks or more serious damage appear on it, the part must be changed in time so that there is no leakage.
Well, it seems, we talked about the most important things regarding the operation of the Samsung Bio Compact S821 washing machine. If you require more detailed information, use the instructions provided with this publication. Good luck!
4. Unbalance error
Figure: 6-4 Imbalance error
- The laundry is not balanced, spread the laundry evenly.
- An error can occur if only one garment is loaded. The end result may be unsatisfactory spinning and an error message is displayed on the panel display (Figure 4).
- The error status can be cleared by turning the mains power on and off (POWER S / W OFF button).
10. Tachogenerator error
Figure: 6-11 Tachogenerator error
- This error occurs in case of failure of the engine tachogenerator or the tachogenerator outputs less than 2 per second
- The error status can be cleared by turning the mains power on and off (POWER S / W OFF button).
11. Short circuit of the motor triac
The error indication is shown in Fig. 6-12
Figure: 6-12 Short circuit of the motor triac
- This error occurs if the tachogenerator registers more than 300 imp. 1 sec after energizing the motor.
- The error status can be cleared by turning the mains power on and off (POWER S / W OFF button).
Error codes on the S621, S821 models :. 1. Water inlet error
Figure: 6-1 Water Gulf Error
- The water filling error occurs when the water level does not cause a change in the pressure switch frequency by more than 100 Hz / min or water is not filled up to a preset level 20 minutes from the moment of the initial filling.
- The error status can be cleared by turning the mains power on and off (POWER S / W OFF button).
7. Pressostat error
Frequency generated by the pressure switch depending on the water level
Level | Low level | High level |
---|---|---|
Incorrect frequency | 30 kHz | 15 kHz |
If the frequency indicated in the table above is recorded for more than 5 seconds, then a pressure switch error occurs.
- When this error occurs, the drain pump will run for 3 minutes. And then stops.
- Then the display shows the error of the pressure switch (Fig. 6-8).
Figure: 6-8 Pressostat error
Samsung washing machine malfunctions
Malfunction of the Samsung S821 fuzzy Logic washing machine. Error during washing. After starting, the washing machine performs all operations as expected for exactly 12 minutes after. Crash. The wash mode indicators (6 pcs.) Start blinking, the temperature indicators (40 and 60) light up constantly. The washer drains the water and stops. The temperature sensor and the heating element were checked. Maybe someone will tell you what the matter is, or what the mistake is?
Most likely, there are problems with the heating element, you can easily check. You need to start rinsing, if the ate goes well. Means a 100% problem with the heating element. In general, this model has error 6.No heating.
CMA Samsung s821 does not drain water. I realized that the pump was faulty in the washing machine. I worked without problems for 5-6 years, and this is not bad for Samsung. Yesterday I took it apart, cleaned the hoses, left the drain right on the edge of the tub. Once everything is fine, the second time again manually draining. Hence the question, what is the number of this pump?
1.47.000.10 Merloni, universal.
We installed the S821 bio compact washing machine. It drains the water, after which the “spin” light starts blinking, but the drum does not spin. The machine has been in operation for 4 years. What could be the problem?
The washing machine is an automatic Samsung S 821 in operation. Tell me, who knows, when you press the start button, an error occurs when the door is not closed. With another module. Works fine. What about repairing the UBL module? What to check?
All along the control line of the UBL. Usually they check the resistors in the piping of the triac, the triac itself. If it doesn’t help. Change ULN (KID). If that doesn’t help either. Change the module.
Malfunction of the Samsung S821 bio compact washing machine. When washing, it starts up increased speed and drains the water, then freezes. When you start rinsing-spinning, the same thing, when you start spinning, it pretends that it works (display), but the drum does not start.
Check the tachogenerator on the engine. 90%. This is a problem in the module on the motor control circuit.
Model S821 fuzzy Logic. After a set of water, it gives an error. The first malfunction was as follows: water flow from under the supply pipe (at the point of connection to the tank), there it is simply inserted and smeared with some kind of glue. Landing on the sealant did not give results. Problem two: when water is drawn, the washing machine stops and all indicators start blinking. Who knows this, advise.
If, before planting on the sealant, you carefully clean the seat on the tank and the hose itself, then it will come off for a while, it is better to replace it with a new hose, but not every hose will do, so it’s not a fact that you will find it. Are all LEDs blinking? Blinking starts during the flood or immediately after it. It is necessary to check the level sensor, whether the heating element turns on immediately when the machine is turned on.
The belt broke for the S821 washing machine (load 3.5 kg). Tell me how to replace it:
1. Perhaps by yourself or only with a special tool?
2. The back wall is cast. How to be?
1. No special tools, only a screwdriver, hands.
2. Unscrew the top cover, press the tank to the front panel, lower the belt between the tank and the rear panel, hook the belt over the motor pulley, pull the belt (with a love spell) onto the drum pulley, check the machine. Belt instead of “native” 1270J3 (white), 1270J4 (black).
The S821 washer, four years old, had a strap off. I put the belt back on, it fell off again. About six months before that, she made a lot of noise during spinning. The workshop said that all bearings should be replaced. Do you think that all bearings need to be changed??
Epiploon 2550,510, bearings 6204ZZ and 6203ZZ.
Tell me, in using the Samsung S821 SMA (load 3.5 kg). When turned on, it immediately gives an error (all modes are blinking, 2 temperatures 60 and 60 Bio are on), who faced this, what needs to be changed?
Can you please tell me what could be? Washer Samsung S 821 used, stood for 1.5 years, did not turn on, only recently changed the pipes and connected it.
1. The fact is that when washing, the CMA gives an error when all indicators of washing modes are blinking 2 temperature indicators (cold and 40 degrees) in the instructions there are no such errors, it was eliminated by turning it off and on, setting it to rinse and spin, then set the washing program again, and it already worked without interruption.
2. Sometimes it collects water and drains it without stopping, and at this time the drum spins and, as it were, washes, turned off the machine, then turned it on, put it on the washing mode, and it washed normally, without any failures.
3. The problem in the washing mode on cotton after washing at the first rinse gives an error that the drain hose is kinked or strongly immersed in water and refused to continue working. Again turned it off and on, put it on rinsing and spinning.
4. Tell me if it is normal for the CMA when washing to take water by about half or almost to the top, and regardless of the weight of the laundry and the washing mode, because basically it collects water by about 1/3.
If, when the water is first started, it picks up an almost full drum, then either the level sensor, or the control module, or the valve does not close. First of all, remove the drain hose from the sewer and hang it on the edge of the sink or bathtub (the end of the hose should be at least 50 cm above the floor) and start the washer. If it does not help, carefully check the peripheral devices (heating element, pump, valves, etc.).
Malfunction of the washing machine Samsung s821 machine with a load of 3.5 kg. The belt broke, wound around the pulley. Remnants of the belt cut off 2 green wires. The first (larger section) comes from a hole in the plastic drum casing. Where exactly. I haven’t figured it out yet, but it is single (maybe from the heating element). The second (smaller section) from the harness, the block of which is connected to the block on the engine. A piece of the second 10 cm wire with a female connector was wound around the pulley. The first. Just torn off, no remnants found. From the diagram. Like both on the “ground”. The question is, am I right? Both to the ground? If yes, please tell me where in the washing machine they were before the break (where is this terminal, where to connect them).
On the machine, all ground wires are the same color. International standard. Yellow-green. Koreans may just have green ones. “Earth” goes to the motor and to the drum bearing assembly.
The washing machine Samsung s821 bio compact is in operation. The problem is this. Changed the ASKOLL drain pump (the impeller broke). I did not touch any branch pipes. When the SMA was turned on. All the water drained out. Where from. Unclear. But soapy, i.E. Water has passed through the detergent drawer. The laundry in the drum is wet and there is no water. Has a drum struck? Or what. Something else? And what to do? When I changed the pump. Turned the unit over. Maybe this shouldn’t have been done?
See the drain hose at the point of attachment to the volute, as well as the tank-pump connection.
The Samsung S821 washing machine is connected. After 10 minutes of washing, the water is drained and when a new one is poured, it begins to drain it directly through the hose, without typing into the tank, while all washing modes and temperature modes are on. There were similar problems here, but I still did not understand what happened to the machine and what needed to be replaced in it? It merges by gravity, just leaves directly. Today they cleaned the drain hose and pump, cleaned it with anti-scale, hung the hose higher, it seems to be washing, but from time to time it stops and something hums quietly in the depths, the lights are on as in a regular wash, without errors. How often can you clean it with decalcifier?
If the water leaves by gravity. Hang the hose so that its end is at a height of more than 60cm. Clean once a month. Descaling agent preferably based on sulfamic acid.
Strong vibration when spinning on the S821 bio compact washer. The drum was overloaded so that it was jammed during washing. During the next washings, during spinning, there is a strong knock (the unit comes off). Washes normally without spinning. Fasteners fell off? Bearings? Where to look? The knocking continues when the water is drained, when I wash, I choose “no spinning” and put some foam rubber behind the drum. Got better. Then the belt broke and, upon opening, found that the crosspiece of the drum, on which the belt is being pulled, moves unevenly, i.E. When twisting, it approaches the drum, then moves away. Is this the cause of vibration during the spin? How to fix?
This is not a spider, but a drum pulley. What you describe is similar to the failure of bearings, if so they need to be changed (along with the oil seal, of course).
We installed a samsung s821 fuzzy Logic washing machine. Washes up to half, does not drain water. After starting to wash. It erases for some time (15-20 minutes), then stops talking and after a while (2-3 minutes). All six indicators flash. Heats the water. The pump is not working. I drained the water by hand. In spin mode. Twists, everything is as it should be, but water (or rather the remains of water, about 1-1.5 cups, that which could not be bled out). Does not drain anyway. Pump Askoll 240xp 40w. Bought a new one. Connect it. Polarity is not necessary? Can you please tell me the error codes and where can I get the electronic circuit from this SMA? I changed the triac for an analogue, the effect is zero, or rather even a minus: it stopped spinning in the spin / rinse and spin modes. In wash mode. Erases 40-50 minutes, then gives an error. Six indicators are blinking and at a temperature of 40C. One. Please tell me what this error is?
There was a similar situation. I checked the pressure switch, the door lock, the temperature sensor on the heating element, the serviceability of the pump, the shut-off valve. Found no malfunctions. I went further along the circuit from the triac, I saw a burned-out resistance of 620 Ohm, it goes to the microcircuit, (I did not write down the name, I installed the unit in place, but if necessary, I will climb in and see) replaced it with what I found, at 1k5, nothing more close was not, took from the player. I tested in spin mode, but did not fill in water, and the pump finally started working!
A Fuzzy S821 washing machine is connected. The wash stops periodically at 40C. The problem is as follows: for some time now, this effect began to appear. At a temperature of 40 degrees, the wash “hangs” almost immediately after the start. While the two rows of LEDs on the left start blinking simultaneously. And that’s all. Only turning off the power helps. But with 60 degrees, the problem practically does not manifest itself. What does it mean? In theory, at 60 degrees, more current is consumed if the matter is in bad contacts. It doesn’t even heat up anymore and the water is constantly leaving. That is, it is collected and merged at the same time. Actually only spinning works.
See errors. When two rows of mode LEDs are flashing. Emergency mode. Diagnostics by temperature LEDs. There is a limited decryption in the instructions. And first, pull the hose out of the sewer and hang it on the edge of the sink or bath.
The Samsung 821 is seven years old. When pouring water, water flows from under the dispenser lid, the washing machine is in the correct position. I tried to glue it with sealants, but nothing good happened. Is it possible to fix this and what is the general reason?
For Samsung, this is a frequent breakdown, if cleaning the filler holes with a brush does not help. Treated by replacing the complete cuvette.
Washing machine Samsung S821 with a load of 3.5 kg. There was a problem with the rotation of the engine in all modes. When the engine is turned on, it picks up speed for three seconds. Then there is a quiet hum in the module and the motor relay is deactivated. And the SMA freezes in silence. It does not give any error signaling. Can you please tell me what resistance the tachogenerator of the electric motor should have (according to my measurements, 9 ohms). This is suspicious. Maybe someone faced a similar problem?
Check the reverse relay on the unit.
We are engaged in the repair of the Samsung s821 bio compact washing machine. Washing goes water is collected and immediately pours out. Called the master, said: “change the control module”, maybe something else?
It is necessary to check the level sensor, and the rest of the peripheral devices, and only then you can deal with the module.
The washing machine S821 is in operation. After the start of the 60 ° C cycle, after 10 minutes the water starts to drain, it gives a “welcome message” 60 ° C and is cold. After replacing the heating element (with a thermistor included), the problem was not resolved. All other modes of the MCA work out normally. When draining, at the end of (for example) a 40 ° C cycle, the water has a temperature of approximately 40 ° C. The washing machine worked flawlessly for 5 years. Buda is glad to any ideas, since the proposal to change the control board somehow did not inspire me. I forgot to say, do not offer a trick with a hose, it is fixed in its own clamp behind the SMA at a height of 60 cm.
This is not an indicator of the correctness of the sewage connection, it is more important that the entrance of the hose into the sewer is at least five cm higher than the water level in the machine.But it does not matter if there is a self-draining, it is easy to determine by turning on the problem mode and watching if there is water topping up wash (not counting the initial fill). And the heating element that you changed should be 800 watts.
Malfunction of the Samsung S821 washing machine. Does not turn on, no power. Washed, washed, stopped. I noticed in the evening, there was water and a ruble inside (I forgot to check my pockets), I got into the filter, I plugged it in cleanly, once several buttons flashed, probably like at the start, very quickly and not for long, and went out, no longer turns on at all. Used 4 years.
You need to check: plug and socket; network filter; transformer in module.
When turned on, the machine immediately drains water onto the soapy floor. No water flows into the drum, the laundry is dry. We reviewed everything, the pipes did not move away, the filters are normal. What could be?
They looked bad. Nozzle bunker-dispenser-tank, tank-pump drain, drain hose, and the tightness of the tank itself. Look for. The heating element falls out of the mounting hole in the front of the forecastle.
The following happens: the machine draws water for a long time, water does not appear in the drum, you can hear how the water is drained by gravity into the sewer. Then the washer spins the drum a couple of turns, again tries to draw water, and so on five times, then an error lights up (which one did not write down for sure). What can be wrong? Perhaps this appeared due to the fact that before that he launched it without water (cold water in the house was cut off).
Hang the drain hose over the edge of the tub or sink and it will go away.
Tell me what could be the reason and how to fix it. The machine is more than 5 years old and recently at the beginning of rinse cycle 1 or 2, the drum breaks off at a breakneck speed, jumps and stops. At first there was a problem with shock absorbers, then I changed them and when I reached the connector (chip) near the engine, the contacts there burned a little. I cut and twisted, soldered the wires, insulated each connection with a heat shrink sleeve. And after that, the SMA worked well for a week, and yesterday this problem repeated again. What to do?
Poor contact or breakage of the tachogenerator. Disassemble the connector again and check everything.
The Samsung S821 washing machine is connected. When spinning the laundry, I first started tapping lightly. After a few seconds, she began to crackle very loudly and debris began to fly out of the bottom. Immediately disconnected her from the network. Upon examination, I found out that the belt was torn into narrow strips and wound them on the drive pulley of the electric motor. Visually, the motor did not seem to be damaged, but found that 2 green outer wires were torn from the electrical socket. Apparently the belt touched them. over, one green wire is thicker than all the others and goes somewhere to the driven pulley, and the other green goes along with the rest. The question is which of these two green wires is the last and penultimate in the electrical connector?
Green is “earth”. The thick one grounds the drum with the shaft, it also connects to the “thin” and grounds the motor (the pin next to the connector on the motor).
I have SMA Samsung S821. Not so long ago the pump broke down, I replaced it, but the washer still does not drain the water. I connect the pump directly to 220, it works, that is, there is not enough voltage from the control unit to operate the pump. Maybe in the control unit, something burned out, or something else? All other functions work fine.
Check the thyristor on the module.
The s821 washer does not want to work under load. It works fine without laundry: twists, heats, squeezes, drains. As soon as you put in at least some laundry. Water is collected, the drum makes a half turn and stops and that’s it. The machine is worth it. Indicators do not give an error, only the specified mode is lit. I would be glad to have a repair tip where to start?
By checking the belt and motor, the belt may have stretched (1270 J3).
Using SMA Samsung s821. The hatch is blocked, after 5 seconds, it gives an error. Help me figure it out, the LEDs are flashing. Cotton, delicate, rinse and spin, synthetics, fast, spin. BIO 60,60,40 is just lit, cold. I checked the heating element, thermistor, tacho, inlet valve, everything is normal. There is no visible damage on the module, the semiconductors are ringing, like whole.
Close the door or check the lock.
Most likely the control module, invite the master and do not suffer.
Malfunction of the Sumsung s821 fuzzy washing machine. The pump stops pumping exactly in the last session, and pumps out during washing. It can be assumed that the pump is broken. For example: it is heating up, but yesterday I checked it a couple of times, not for washing, but for spinning. Does not want the pump to work, removed it, connected the hoses according to its diameters and started it up, pumped out 10 liters very quickly, put it back and checked everything the same for spinning, is silent.
You just need to replace the pump with a new one.
The SMA will run for a few minutes and then stop. Please tell me what this error is. I turn it on, set the program, it will run for several minutes and stop, 6 washing modes on the panel are blinking, and the 3 lower temperature diodes (cold, 40 and 60) are on. I turn it off, then turn it on and after 10 seconds, the same error. I examined all the periphery and the control module, did not reveal anything suspicious. I suspect that this breakdown may be associated with a poor contact in the outlet to which the washing machine is connected (the wire is broken off)?
Judging by the description. Cold, 40, 60. Water level sensor error.
Installed washing machine Samsung F813j sensor compact. In work six months. Maybe someone knows the answer to such a question. When the water is drained, the pump works more or less quietly, but when the water runs out, it starts to buzz unpleasantly intermittently, then quietly, then loudly. The impression is that it will suck in water, then no.
So the problem is only in the noise or does the pump still not pump? If this is a problem. We replace everything, I have a negative attitude to pump repair because of the danger of flooding and unreliability.
We are repairing a Samsung F813J washing machine with a load of 4.5 kg of linen. It draws water and then stands for a very long time, then shows the error “EA”, tell me the reasons.
No motor rotation.
Samsung F813J washing machine is connected. Error E7 pops up. Started over at spinning now a few seconds after switching on.
Check the level sensor (best of all by replacement) and its branch pipe.
The F813J machine washes normally several times, and then abruptly does not want to drain the water, writes E2 (clean the filter). I drained the water by hand, cleaned everything well, then the machine again washes it normally several times and again the pump does not drain the water. After you drain the water by hand, it will wash normally several times again. I realized that something is wrong with the pump and it needs to be replaced. Is it easy to change it yourself or is it better to call the master?
It is not difficult to replace the pump yourself, it is enough to have only the new pump itself, a Phillips screwdriver.
Washing machine Samsung F813J sensor compact. Does not spin after a wash cycle. Works fine without laundry. After draining the water, it seems to be unable to decompose the laundry. Sometimes it takes some time, and the washing process goes on, but it takes a lot of time. Tell me where to look for the malfunction. Will replacing the control board work? The wires and contacts are fine. I will look for a control board. Maybe somehow you can adjust the sensitivity on the board to this layout of laundry? I read somewhere that some washers have an adjustable resistance. Maybe there are some options on this board?
If the lack of spin is not constant, replacing the module will give you nothing. Laundry layout and imbalance determination software, is present in all these modules.
Malfunction of the Samsung F813J washing machine. Plugged in, voltage is present. And it does not turn on. I press the network button, no reaction, everything is silent, there is no indication. What to check?
You need to check the module (transformer), and look at the button itself.
The washing machine F813J is in operation (load of linen 4.5 kg). When you turn on the washing machine, all the indication is on, everything is fine, but setting the program. SMA does not twist anything, stands and is silent. Where to begin? When you turn on the machine, the whole panel is on, nothing seems to be terrible. We select a program, the door does not lock at the same time (and you can select both the spinning and the washing program, any program)! Water is not poured, not drained. Supply voltage within the normal range of 219-221 volts.
Samsung F813J sensor compact gives error code Ec. The problem is this. When the machine is turned on, it costs about five seconds, after which the hatch lock is triggered and the above-mentioned error Ec is displayed. All peripherals have been checked. For visual inspection, EM is in order. What’s next to check?
EU. Signal from the thermistor is less than 0.2V or higher than 4.5V (open or short of the thermistor).
Only the program starts at 95 degrees. The pump worked once. Replaced, the drain works fine. The rest has not changed. What else do you need to check? The switch works. Picks up water and stops.
Check valves, level sensor, temperature sensor and heating element.
The washing machine Samsung Fuzzy S1021 (load 3.5 kg) is in operation. Washes fine, but when it comes to spinning and draining, that’s where it ends. The lights on the panel light up and there is silence, no further actions or sounds occur. This does not always happen, for example, today I washed one wash normally, and again did not wring out the next one. I disassembled the drain system, everything is clean there (I thought it might be clogged). It happens for a while it will stand and then it will work again.
On the eve of the washing machine Samsung Fuzzy s1021 worked fine, however, something crunched there. Today I turn it on. Does not turn on. The panel does not light up. I remove the cover, remove the control panel. Hoped there were some fuses. There are no fuses. I pulled out and inserted the plugs into the control panel. Reactions 0. The plug, leading the round, felt the indicator. Electricity comes in. I put it back together and turned it on. The panel is working. I saw that I had put the lid on the washing machine incorrectly, disconnected it from the power supply, rearranged it. It does not turn on again. Just in case, I cleaned the water filter (the pressure is supplied) and the filter at the bottom. There, a piece of plastic was wound on the impeller (maybe it had made noise the day before). It does not turn on again, the LEDs are off.
Yes, it is necessary to check not with an indicator, but with a tester: the indicator shows the presence of a phase, but how can you check zero? We take a tester and start checking from plug to module.
The belt on the Samsung S1021 broke (I found it under the washer on the floor). It is necessary to raise a new question, respectively. Which belt (brand, where to get it in St. Petersburg) is suitable for such a washing machine and, if possible, indicate the manual on how to replace the belt (or here in a nutshell, if it’s not difficult).
A belt of any brand with the marking 1270 J3 will do, you can put it on through the top by removing the top cover.
Malfunction of the washing machine Samsung s1021 machine with a load of 3.5 kg. Standing, drum (don’t spin). When the SMA starts, the electronics seem to work (full cycle) from loading water to draining, only the drum is standing and not spinning (the belt is intact), I suspect that the engine has burned out. Tell me, maybe you still need to check? Maybe I missed something?
Pay attention to the integrity of the wires on the motor terminal block.
I disassembled the forecastle on the S1021. Please help me with the following information: Bearing number; Oil seal number;