iPhone says that headphones are connected

Why is the iPhone showing that headphones are connected??

The most common cause of iPhone locked in headset mode is dust or dirt that gets into the 3.5mm jack. The solution in this case is the simplest cleaning of the connector with any thin object, for example, a needle or a toothpick.

Where are the headphone settings in the iPhone?

Configuring Airpods Settings on iPhone

  • Open the Airpods case.
  • On iPhone, open Settings Bluetooth.
  • Tap the button next to Airpods in the device list.
  • You can follow the steps below. Change the name of your Airpods. Tap the current name, enter a new name, then tap Done.

What to do if the iPhone says that headphones are connected but they are not connected?

If your iPhone has headphone mode turned on, which doesn’t turn off in the usual way, follow these steps:

iphone, says, headphones, connected
  • clean the connector with a toothpick
  • blow dust off the nest
  • reboot the device with the headphones on
  • turn on speaker mode
  • adjust the volume
  • turn off wifi.

What to do if the phone sees headphones but they are not connected?

If your phone, smartphone on Android or iPhone shows that headphones are connected, but they are not there, you need:

  • Clean the connector from ordinary dirt with a thin cotton swab. Attention. do not do this with a needle, so as not to damage the contacts;
  • Clean the nest from oxidation using the same cotton swab and alcohol.

Flight mode activation

The method of turning on and off the “flight” mode is not often used. Its effectiveness is due to the fact that the device is still formally connected to headphones, which will help eliminate this method.

During its use, the Bluetooth module is disabled, which affects the problem. To activate the flight mode, you must press the power button, and then select the appropriate command. the icon depicts an airplane.

Software recovery

To combat the breakdown, you can try updating your phone to the latest version of iOS. This will help to remove the imperfections of the previous one, because the developers fix errors with each new version. To do this, you need to enable automatic updates in the Software Updates Settings.

Try connecting a bluetooth earphone

Try connecting the device to the speaker via Bluetooth or Bluetooth headphones, and then disconnect it. See if headphone mode on iPhone turns off when headphones are disconnected!

By connecting the iPhone to a Bluetooth device, you can exit the “headphone mode”. To do this, first turn on Bluetooth (“Control Center” or using the settings).

After connecting to the bluetooth speaker, play the song. When playing a song, turn off the Bluetooth setting on your phone. This will fix the device error.

One of the headphones is quieter on iPhone 5. what to do?

Over time, any device fails, temporarily fails or breaks down completely. Our task is to determine the type of breakdown and decide what to do. repair or buy a new one. often than not, almost any breakdown can be repaired. But the question is different: is it worth the time and money. One of your headphones on the iPhone 5 may play less well than the other. This means that we can probably solve such a breakdown at home.

Read more:  How To Delete An Account On An Apple Id And Icloud Iphone

First, make sure that the headphone mesh is clean, the port sees connections, and the wire is intact:

  • Open the settings of your fifth iPhone; Open the iPhone settings
  • Next, select the item “Basic”; Select the item “Basic”
  • We find the line “Universal access”; Click on the line “Universal access”
  • We get to the window with the settings for sound and other parameters.

This window contains a knob that allows you to adjust the balance between the left and right channels on iPhone 5. Adjust them so that both headphones sound roughly the same. By default, the slider is centered. Suppose, in your case, there is a problem with the left insert. try to move the balance slightly to the right. In this case, the overall volume will be slightly underestimated. But on the other hand, you will be able to receive sound of equal volume from each earphone.

Adjusting the sound after adjusting the channel balance

When the sound balance is adjusted, try increasing the overall volume using the buttons on the cabinet or programmatically. There will be no significant loss of sound. If your headphones cannot see the iPhone X / 8/7/6/5 device, or the sound of one of them is quieter than the other, use all the above methods to solve the problem.

iPhone does not see headphones, what to do?

There are several types of headphones for iPhones: traditional wired, with which each of us is familiar, and wireless of the new generation. Apple gave them the name Airpods. After the release of the headset and its appearance on the shelves, the manufacturer faced complaints from users that there were flaws in the Airpods. Let’s consider this problem in more detail in this article and try to find solutions, for what reasons the iPhone does not see the headphones and why the iPhone headphones do not work.

First, we’ll follow the correct path to consistently set up Airpods:

iphone, says, headphones, connected
  • Go to the “Home” window;
  • Open the case with Airpods and place it next to the iPhone;
  • The installer splash screen appears on the phone;
  • Next, we find the “Connect” button and select “Finish”.

If you set Hey Siri on Airpods (2nd generation), it will work through your headphones. When this option is used for the first time, the options for configuring it are initially opened. When iCloud is working, the headset syncs automatically.

Why iPhone thinks headphones are plugged in?

There are several reasons that can lead to this problem. The most common are dirt, dust or water particles entering the connectors.

In addition, the smartphone may start to work incorrectly due to high humidity or mechanical damage.

iPhone Thinks I Have Headphones Plugged In. How To Fix

How to Disable Headphone Mode on iPhone: Why iPhone Thinks They’re Connected

Both the iPhone and iPad have two different volume modes called Headphones and Ringer. These modes work separately from each other, allowing the smartphone to automatically change the volume level when the user unplugs or plugs in the headphones.

The volume level set in the “Headphones” mode will turn on every time this gadget is connected, while it will not affect the volume level in the call mode, allowing you not to change the sound level every time. When headphones are connected to the iPhone, the current mode is displayed on the screen as a window with a bell or speaker.

In some cases, when the headphones are disconnected, the mode may not change automatically and the smartphone will remain in the “Headphones” mode instead of going to the “Call” mode. In this case, the device stops playing sound.

How to turn off Headphone mode on iPhone?

In this situation, you need to connect the headphones to the iPhone and listen to any sound in them, for example, the sound of the lock screen or clicks of the on-screen keyboard. The sound should only be played in the headphones, not from the speaker, otherwise the device is faulty. After that, you need to disconnect the headphones and check the sound on the device speaker using the side buttons. The volume indicator in this case should be in the “Call” mode.

Read more:  How to Unlock iPhone 10 without Passcode

If, when the headphones are disconnected, the “Headphones” mode is still displayed on the iPhone. do not rush to give the device to specialists from the service center. there are several ways to fix this problem yourself at home. Before trying the recommendations described below, you need to remove the cover and analyze the last manipulations with the device.

  • Reboot and charging cable. First, try turning off and on your iPhone (with headphones disconnected) with the charging cable connected. If this method does not help, you can do the same, however with the power adapter connected to the outlet and applying a hard reset instead of a normal shutdown.
  • Toothpick. If the headphone jack is rarely used, it can become clogged with dust and dirt from s. It can be removed from there with a toothpick, needle, cotton swab or corner of paper, after turning on good lighting and making sure there are foreign elements.
  • A vacuum cleaner. Moisture may accumulate in the connectors in cases where the device is very wet or has been dropped into water. It can be pulled out with a vacuum cleaner, however, if a lot of time has passed since the moment moisture got into the phone, this method may not help due to the appearance of rust on the contacts.


Sometimes, simply restarting your iPhone with a wired headset connected is enough. If a regular reboot does not help, it is worth resorting to a Hard Reset. Usually, for this you need to simultaneously hold down two buttons: Power and Home. It is necessary to keep them until the brand logo appears on the screen.

How to fix

So, the sound on the iPhone disappeared, it says that the headphones are connected, what to do in this case. Most often, the problem can be solved literally within a few minutes by following the tips below.

How to Exit Stuck HeadPhone Mode on iPhone 6 & iPhone 6s & Plus

Connecting a wireless headset

Connect a wireless headset (or any other Bluetooth device for audio playback) to iPhone. In this case, it is worth observing the following sequence of actions:

  • Connect wired headphones;
  • Create a pair with a Bluetooth device and output sound to it;
  • Disconnect wired headphones;
  • Disable the wire-free device.

Causes of the problem

There can be many reasons why the iPhone does not play audio through the speaker. First, let’s figure out how it works. The smartphone “knows” about the state of the headphone jack by measuring the resistance of the circuit. When the contacts inside the connector are closed, the phone “understands” that the headphones are connected and the sound needs to be output through them, and not through the speaker. Accordingly, the speaker is muted and the signal is sent to the connected headphones. However, false short circuits are also possible without connecting devices, then the speaker of the phone is disconnected by it itself, and the sound empty sound jack.

Here are the most common reasons for this:

  • The problem with the headphone jack itself on the smartphone.
  • Poor quality headphones coupled with software glitch.
  • Software glitch right at the moment the plug is pulled out.
  • Unlicensed software.

These are the most common causes of a problem. We will analyze how to eliminate.

Cleaning the connector

It boils down to cleaning the headphone jack (for the iPhone 6 it’s 3.5 mm, for the seventh and older Lighting). Dust can simply get into the connector or it can oxidize if moisture gets in.

For cleaning, you can use a cotton swab, needle or toothpick. Additionally, the walls of the connectors can be treated with alcohol.

Another option is to blow through the hole. Alternatively, you can use a vacuum cleaner. If you don’t mind spending money, you can buy a can of compressed air, which is designed to clean electronics.

Another option: turn the headphones on and off the phone several times (possibly up to 10-15). This operation will also allow you to clean the connector, because the headphone plug fits snugly into the hole.

It is worth noting that the manufacturer’s technical support recommends the latter method, since in this case there is no need to insert foreign objects into the connector, which means that the risk of damaging the inside of the smartphone is minimal.

Read more:  Doesn'T Download Internet On Iphone

When the iPhone thinks it has headphones in it

Apple smartphones are known to be some of the most reliable. However, even with them, problems sometimes arise. A fairly common failure is the lack of sound from the speakers. At the same time, the gadget writes that headphones are inserted into the smartphone, although the connector is empty. This problem occurs in the iPhone 5, 6 and others, in all where there is a jack for connecting a wired headset. We will understand the causes of the problem and how to fix it.

Change of headphones

If you have used inexpensive (very inexpensive) headphones, then the problem is most likely with them. Connect another device and restart iPhone. To avoid such problems, use branded original headphones and headset.

Possible problem

Your phone probably “thinks” that the headphones are plugged in due to a system failure. This may apply to both wired and wireless headphones.

Failure can occur for the following reasons:

  • The phone has been used for a long time and the motherboard has overheated
  • The headphones were removed while the melody was playing, as a result of which the device has not yet had time to complete all previous processes and freezes
  • The smartphone was dropped along with the connected headphones, after which the headset was hastily removed.

The best solution in this case is to simply reboot the phone. If the problem was a system glitch, after a reboot, the indicator will turn off by itself.

If a serious system failure occurs and the reboot does not help, then in order to fix it, you will need to reset the smartphone settings to the factory settings. Before performing it, be sure to back up your data.

The phone shows that headphones are connected: what to do?

On almost all modern models of phones and smartphones, when accessories are connected, an indicator appears that notifies the user of what exactly was connected (headphones, Bluetooth headset, etc.).

But, if the phone shows that headphones are connected although they are not, then there is definitely a problem. Below we will tell you how to solve it.

Possible problem

If the phone says that the headphones are connected, but restarting does not help, then in the case of wired headphones there may be a problem with the connector.

The connector means the headset jack. 3.5 mm, USB Type C, Ligthing

It is possible that a foreign object or moisture has got into it.

The ingress of moisture on the contacts can cause not only constant system failures, but also provoke corrosion, which, once started, will disable the entire device in a short period of time.

What to do?

First of all, inspect the headphone jack for foreign objects. These can be both specks and pellets from clothes. They can be removed carefully with a toothpick or needle. But be careful not to damage the contacts.

If there are no foreign objects, check for moisture. If it is there, you can carefully remove it with a needle, after winding a little cotton wool around it. In addition, you can dry the connector with a regular hair dryer in a cold mode.

If you are well versed in the structure of your smartphone, you can try to disassemble it and clean the contact area of ​​the headphone jack with a special compound.

However, given that many modern models are made very cleverly, it is better to abandon independent manipulations and hand over the device for repair to a service center.

In this article, we told you what to do if the phone says that the headphones are connected. We hope the advice helped you. If you have questions. write in the Комментарии и мнения владельцев.

Read other instructions for mobile phones and smartphones in the section Instructions and help for smartphones on our website.