IPhone is out of power and won’t turn on while charging

Improper use of smartphone battery

If your iPhone turns on and immediately turns off, or if it spontaneously reboots and the shutdown button doesn’t respond, the battery might be faulty. If you have been using an iPhone for more than a year, then the loss of battery capacity is quite natural and replacing this part will help solve the problem. When the iPhone is almost new, the battery breakdown is most likely caused by the following factors:

• using a non-original charger. despite the similarity of original and Chinese-made chargers, they differ in the way they supply current, as a result of which the battery breaks down, so the iPhone starts to turn on and immediately turns off
• regular power fluctuations. using the original iPhone charger does not always guarantee battery health. With constant power surges, the battery breaks down prematurely, so the iPhone turns on and starts to die out, or a notification appears on the screen that the device will soon be discharged
• moisture ingress. if even a small amount of moisture enters the battery, the battery breaks down, so the iPhone turns off immediately, or does not charge when turned on

Mechanical damage, falls, and shocks can also cause the iPhone to turn on and off. If the iPhone starts to turn on and off, the charging icon is always on on the display, it is recommended to diagnose the device.

The “apple” is constantly lit on the phone screen

A common situation is when the iPhone turns on, the charging indicator appears on the screen, after which it goes out and the “apple” logo appears, or a notification that it will soon be discharged. If the iPhone freezes and turns off immediately after turning it on, most likely the reason is a system crash when restoring from a backup. Restarting the gadget and restoring from iTunes will help to solve this problem.

• make sure the battery is charged and not discharged anytime soon
• prepare your computer and USB cable
• sync iPhone to PC
• turn off your iPhone while holding down the Home button and the Power button
• hold down the power button and wait for the iTunes application logo to appear on the screen
• release the power button and start recovery mode on the computer

After the restore is complete, the iPhone turns off immediately. Charge your iPhone and wait until it is full. Then press and hold the power button for a while and, if necessary, reboot the device. If this did not help to solve the problem, and still after turning on the iPhone immediately turns off, a professional iPhone diagnostics is required.

iPhone turns on but black screen is on

Conventionally, the reasons why the iPhone turns on and off while charging, performs a spontaneous reboot, are divided into hardware and system. It is software glitches that are most often to blame for the fact that the iPhone turns off immediately. If your iPhone stops turning on, you need to diagnose the device. When the firmware is the cause of the breakdown, the following should be done:

• connect charger
• leave the phone on charge for 15-30 minutes
• try turning on your smartphone
• if the phone turns on, restart it. press the Home button and the Power button at the same time

If the reason that the iPhone turns on and off immediately lies in system failures, after a forced restart of the device, the “apple” logo will appear on the iPhone screen and iOS will start loading. Charge your phone fully and test it. If the problem persists, look for another cause of the problem.

iPhone turns on and off while charging

And get the best deals from trusted masters.

• Compare and choose the best conditions
• Feedback from interested professionals only
• Don’t waste time communicating with intermediaries

A very common problem faced by users of Apple gadgets when the iPhone turns on and off while charging. There are many reasons why the iPhone starts to turn off and you can fix many of them yourself.

To solve the problem of turning on, spontaneous reboot or failure of the shutdown button at home, it is necessary to consider in detail all the possible causes of the malfunction and how to repair them.

IPhone shuts down due to unstable charging source

If your phone doesn’t charge when you turn it on, or it starts turning on but turns off immediately, an unstable iPhone charging source could be the cause. If you charge your iPhone in a garage, car, or summer cottage, it affects the device’s performance, since the power supply in such places is unstable. To prevent damage to your phone, follow these guidelines:

• if iPhone turns off and on regularly, do device diagnostics
• only charge your smartphone in places where the power supply is stable
• do not use charging from other phones
• try not to use car chargers

If you follow the recommendations for using the iPhone, as well as regularly diagnose the device, iPhone problems occur much less often.

The phone stopped turning on due to hardware problems

If iPhone stops turning on when charging is connected after being bumped or dropped, a component of the phone may be damaged. In this case, the charging indicator is on on the screen, the Power button (shutdown button) responds to commands, but the phone does not work correctly. To find out if this is so, you need to make a professional diagnosis of the device.

The main components that affect phone performance are as follows:

iphone charging but not turning on, iPhone stuck on red battery screen. solve it at your home

• motherboard. if the motherboard fails, the phone turns on, then the screen goes blank and the device turns off
• charging controller. if you cannot connect the charger because the plug does not fit all the way, make a diagnosis of the charging controller. The smartphone may have stopped turning on because of it
• Power button. if the contact of the shutdown button is oxidized, sooner or later the phone turns off and does not turn on anymore. In this case, mandatory diagnostics and repairs are required.
• battery cable. when the cable connecting the battery to the microcircuit comes off, the iPhone does not charge correctly, so it periodically turns off and turns on spontaneously

If your iPhone stops charging, or periodically turns off and on due to hardware problems, it’s not recommended to make repairs yourself. Diagnostics and replacement of faulty parts of the gadget should be carried out using professional equipment.

Professional smartphone repair

If your gadget has stopped charging, the charging icon is lit on the display, but the battery capacity does not change, or it freezes and cannot turn on, urgently call an experienced wizard registered on Yuda to diagnose the phone. Private specialists make iPhone repairs on more favorable terms than service centers, and also provide the following advantages:

• repair of Apple smartphones of all models and modifications
• use of original spare parts when replacing
• guarantee for all work performed
• minimum cost of repair

Professionals will be able to fix an iPhone in a short time, depending on the type and complexity of the breakdown. If the iPhone turns on and off while charging, urgently fill out an application on the website and choose an artist.

iPhone Won’t Turn On After Discharging

And get the best deals from trusted masters.

• Compare and choose the best conditions
• Feedback from interested professionals only
• Don’t waste time communicating with intermediaries

Everyone can face a situation where the iPhone is charging but not turning on. Perhaps the cause of the breakdown is serious, and you will have to repair your smartphone for money. However, in some cases (for example, if the connector is dirty or there is a software failure), you can fix the malfunction at home without having the experience, qualifications and tools. It is worth trying to find the problem yourself and restore the phone to work.

What are the causes of iPhone malfunctions

Many iPhone owners are experiencing difficulties: the gadget is slowly charging or does not turn on at all. And if a minor problem (for example, a breakdown of the Home button) is not so critical, then in such situations it is impossible to use the phone.

• critical internal parts (tristar controller, sync loop, power controller, motherboard or battery) are damaged due to mechanical impact (shock, falls) or liquid flooding
• a faulty, non-original charger is used (cheap Chinese fake)
• breakage of the Lighting connector or its contamination caused by dust, hair, lint and other small debris
• software failures (software directly affects the microcircuit that controls the charging process)
• the USB port of the tablet or stationary computer is broken
• factory defect of Apple components involved in the battery charging process

Errors during the operation of programs, breakdown of chargers and iPhone parts (batteries, connectors, cables, etc.) can manifest themselves in different ways. A few examples:

• iPhone won’t turn on after being discharged (when the battery is low)
• the application hangs, does not respond to taps, or the screen is completely black
• the gadget turns on, but hangs after the Apple logo appears
• the indicator is on, but the charge level is very low even for a long time
• iPhone is dead and does not turn on when charging from a cigarette lighter or computer

Before taking your smartphone to the service center, make sure that the cause of the malfunction is a breakdown in the hardware. And in any case, do not postpone the trip or the call of the master if you spilled water on the iPhone. every hour of delay can aggravate the situation.

How to get your iPhone back on track

If you have problems with turning on and charging, first of all, check if there is current in the outlets. Next, if the phone does not turn on at all, connect it to the charger. In a normal state, the gadget immediately writes that it is charging. the indicator is on, which means the process is in progress. Remember that the battery is not designed to operate in low temperatures. Therefore, warm up the smartphone before connecting the charging, if the battery runs out in cold weather.

Another situation. you are trying to start an iPhone that has been discharged for a long time. If the battery goes to zero, you need to wait 15-60 minutes and only then press the Home or Power button.

The smartphone still does not respond. we perform a hard reboot:

• press the power and home buttons at the same time (for 7th generation devices. “Power” and the volume control button)
• wait 10-20 seconds until the Apple logo appears on the screen of the gadget
• release the buttons. the operating system will start in about one minute

This method also helps with other problems. For example, when the program hangs or there is no response to buttons.

When the Apple logo is on and off again, you need to restore. Most likely, the battery has run out due to a software failure. The error was caused by an unsuccessful iOS update or downloading and installing unlicensed software.

• run iTunes on the computer and insert the USB cable into the connector
• turn off your smartphone using a combination of the Home and Power buttons (if you have an iPhone 7, use the volume button instead of Power)
• press the “Home” button and, while holding it, connect to the computer
• hold Home until the phone screen starts showing the iTunes logo and plug icon
• the computer display should display the message “There is a problem with your iPhone; it needs to be updated or restored “
• confirm recovery

Downloading and installing a new version of iOS will take about 30-40 minutes. There is another recovery method. DFU mode. The method is radical, as it destroys all data on the phone. Stages:

• connect the charger (the charge level must be greater than zero)
• after five minutes, disconnect the charger, connect the smartphone to a computer (stationary or tablet) and turn on iTunes
• simultaneously press Home and Power, hold them for exactly ten seconds, then release the on and off button
• keep “Home” (15-30 seconds) until the notification in iTunes (when you enter DFU mode, nothing should be on the phone screen)

Then you should confirm the procedure and click on the “Restore” button. If you forgot to overwrite data from your phone, you can undo the restore: disconnect the USB cable, hold down Home and Power for 10 seconds. Then the iPhone will restart.

If everything is fine with the software, inspect the connector for contamination. The litter clogged in Lighting should be carefully removed using improvised means, for example, a toothpick.

When charging the battery from a computer, consider the functionality of the USB port. Possibly not enough amperage. try a regular Apple charger.

Pay attention to the charger itself. Even if the original Apple cables are fragile. the sheath and cores are easily damaged. what to expect from cheap Chinese products. The phone may stand for a long time and show charging, but it will still be zero if the charger is fake or broken. Use only original charger to avoid similar problems.

iPhone X/XS/XR/11: Won’t Turn On While Charging for Long Time?

If the above actions were unsuccessful, most likely the battery discharge was due to normal wear and tear, factory defects or damage. If you dropped or flooded your phone. don’t even look at the indicator: take the gadget for repairs as soon as possible or call a specialist home.

iPhone is dead and won’t turn on anymore

Apple smartphones are distinguished by high performance, functionality and a rather powerful battery. For example, the iPhone X lasts more than 40 hours when listening to music, and more than two days in standby mode. Recently, however, more and more users have begun to notice that the iPhone is quickly discharging and heating up when charging. Many attribute this to the release of the new iOS 11 system, which consumes more power than its predecessors. You have to charge a gadget with a new operating system several times a day and additionally put it on charge for the whole night.

Sometimes it happens that the iPhone is completely discharged and does not turn on anymore, and there is no charging icon on the screen. The reasons for this may be:

• faulty charging;
• low throughput of the charger;
• battery failure.

What to do?

Most importantly, do not panic and do not try to disassemble the device. First, check if the charger is working properly by connecting it to another smartphone. If the device is charging normally, then most likely it’s time to replace the iPhone battery. This can only be done in a service workshop, since the design of the Apple smartphone is non-separable.

If, when the charger is connected, a battery icon appears on the screen, but the gadget does not charge or turn on, the reason may be iOS freezing. This happens when the battery is deeply discharged. To fix this problem, charge the device for 6-8 hours and then try turning it on. When the smartphone starts successfully, observe how long it holds the battery charge.

Another way to turn on iPhone is DFU recovery. To do this, you need to connect your phone to your computer, go to iTunes and click the “restore” button. In most cases, this procedure will help turn on the device.

If all the above methods did not help, contact the service center for diagnostics. Free diagnostics at rem-iPhone centers.

iPhone is dead and won’t turn on while charging. what to do

The smartphones of the “apple” manufacturer, although they differ in the quality of workmanship, but the equipment deteriorates over time. Therefore, users find that the iPhone is dead and won’t turn on while charging. Smartphone owners panic. it is expensive to repair Apple products, even if the model has been on the market for a long time. The list of possible causes of breakdown is not limited to a banal fall or falling into water, so you need to carefully examine the phone. In some cases, it is possible to correct the situation on our own, and in this article we will consider how to turn on the iPhone if it is completely discharged and stops giving “signs of life”.

Hard reset

If your iPhone is completely discharged and won’t turn on after an incorrect update or firmware, a hard reset will fix the problem. For this you need:

• hold down the “Power” and “Home” keys;
• wait for the Apple logo to appear;
• the phone will reboot and turn on.

This method will help if older models, including “seven”, “six”, “five” or iPhone 5S, will not turn on or charge after being discharged. Hard reset of new models occurs differently, this is done to protect user information from accidental clicks.

• Quickly press the volume up key.
• Press the volume down key quickly.
• Hold the side button until the “apple” logo appears.

After the performed manipulations, the smartphone will turn on.

Charger problems

Often the reason that the iPhone sat down and does not turn on while charging is a faulty cable. In the places where the wire and the adapter are connected, users find creases. No electricity is supplied to the device, so a discharged phone will not turn on. It is worth carefully examining the charging. this will allow you to detect a breakdown in time.

Connect the iPhone to another charger. if the phone turns on, the cable will have to be replaced, sometimes the breakage cannot be detected with the naked eye. Also, the reason may lie in a faulty outlet, so you should not panic ahead of time. A banal solution to a problem often turns out to be the right way.

Smartphone malfunctions

Users have complained that the iPhone will not turn on after being completely discharged due to being dropped or submerged in water. Only a technician in a service center can reliably find out why a smartphone does not want to work. The reason lies in the breakdown of the battery, cables, display, motherboard or processor. the technique requires careful handling. The experts warn that it is better not to look inside the device unnecessarily, so as not to break the iPhone. And simple tips will help to avoid breakdowns:

• do not discharge the phone to zero;
• let your smartphone “rest”;
• update iPhone only using official programs and firmware;
• charge the device with specialized chargers.

Follow these rules, and then the iPhone will work for a long time without errors. And remember that smartphones also have an operational life, and old equipment fails due to age.

iPhone is dead and won’t turn on. what to do?

Recently a friend asked for help. Said that his iPhone is dead and won’t turn on while charging. What to do in a similar situation? Personally, I’m a fan of the Android operating system, so I went to the Internet for answers. I “dug up” several ways that can help, but not always. Now let’s look at the instructions for the iPhone.

Common problem

Judging by the messages on the forums, such a negative phenomenon is rare, but it does take place. And this must be somehow dealt with. It is good that in the vast majority of cases, you can do without going to a service workshop. This means you can save a lot of money (yes, repairing the iPhone 7 and other models is not cheap).

Why won’t my Apple smartphone turn on after plugging in the power adapter? The reasons are as follows:

• The device was in a discharged state for a long time (from several days or more);
• A software failure has occurred;
• The charging socket is damaged, or there is another hardware failure preventing the phone from being powered up.

If iPhone is dead and won’t charge. what to do?

Based on the listed factors, we will consider effective solutions.

• When the battery is completely exhausted, connect the original “charger” to the iPhone, connect it to the mains and wait about fifteen minutes. At first, the screen will be black, but later an icon should appear indicating the start of the process:

Suddenly Afyon 6 does not start even after half an hour, but a “hint” appears on the display. they say you need to connect to an outlet, then do the required operation and wait at least four hours until the resource is 100% restored:

• If there is a software-type failure (the methods listed above are powerless), then you will have to resort to a “hard reset”. Hard Reset is simple, but after it all installed applications, data are deleted, that is, you get an iPhone with a clean firmware.

It is necessary to hold down and hold two buttons on the case. Home and Power (inclusion). If you have a new iPhone that doesn’t have a Home control, then hold down Volume instead:

Do not let go until the display shows “bull’s-eye”. This usually happens in twenty seconds. The first start after the reset will take longer than usual, you will have to wait. And then immediately put it on charge, after which you can restore information from iCloud.

If it doesn’t help

I don’t want to upset you, but if the listed solutions to the problem are ineffective, most likely the reason is a hardware failure:

• The battery is “dead” completely. it will need to be replaced at a service center;
• Charging cable damaged. try using a different one;
• The slot for connecting the power supply is broken. you will have to contact the SC to replace the connector;
• Critical failure of the base “firmware”. alas, you won’t do anything at home.

Now you know what to do if the iPhone is dead and does not turn on even when the charger is connected. Try it and be sure to write in the Комментарии и мнения владельцев which method was useful for you.

Checking the charger

Is your iPhone showing it’s charging but won’t turn on? The problem may lie in a too low charging current. As a result, a discharged battery cannot gain enough charge to start the smartphone. We do not have the opportunity to get into the interior of the smartphone with a multimeter and check the charge current. But what prevents you from using a known good charger? We carry out the following actions:

• We find a known working charger that successfully charges other smartphones;
• We connect the current iPhone to the charger;
• We leave for the night.

Please note that if, after such a charge, a rapid discharge of the battery is observed, you should contact the service center to replace the battery.

Charging problems are common when using non-original chargers made by third parties. If you want to avoid these problems, use only original Apple-branded accessories.

iPhone is dead and won’t turn on while charging

If iPhone is completely discharged and won’t turn on. then the first thing to do is not to panic, because there are several ways to make it work. But first you need to figure out why it does not turn on. After all, even if you forgot the password on the iPhone and you don’t know what to do, the battery charge is still saved. Basically, there are only two reasons an iPhone might not work: the first is a completely drained battery, and the second is a software glitch. Let’s deal with each of them.

What to do if iPhone won’t turn on due to dead battery

If the phone runs out of battery, then you need to connect it to the mains adapter and charge for fifteen minutes (some models take half an hour). After the specified time has elapsed, it is recommended to try to turn on the mobile device, but do not remove it from the socket. If everything goes well, the icon of an empty battery inside with a lightning bolt should appear on the screen of the gadget (this means that it is charging and will soon turn on). In some cases, if the iPhone is completely discharged and does not turn on even after half an hour of charging, an empty battery icon, an outlet and an arrow pointing to lightning may appear on the screen. This means that the battery of the gadget was completely discharged (or did not turn on for a long time), so it needs additional time to recharge (approximately four to five hours, after which it can be turned on).

What to do if iPhone won’t turn on due to software glitch

If there is a software failure, then the gadget requires a hard reboot. To do it, on the iPhone, you need to simultaneously hold down two buttons at once: Power and Home. They should be held pressed for about 10-15 seconds, after which the Apple logo should appear on the screen of the gadget, which will mean that the device has started rebooting. If you already know how to tell the difference from the original iPhone 3GS, you’ve probably seen this icon. After the reboot is complete, the phone will function normally. It is worth noting that the same reboot can be done if a program freezes and the phone does not respond to pressing any buttons.

The above problems and their solutions are standard, but if none of these methods helped, then most likely one of the following malfunctions occurred on the phone:

With all of the above problems, it is recommended to contact the service center, because it will be very difficult to solve them on your own. Although nothing is impossible in the world!

iPhone shows charging but won’t turn on

Apple specialists have succeeded in creating convenient, fast and reliable iPhone smartphones, which have won popularity among millions of people around the world. But, despite the high level of reliability, breakdowns do occur in them. If iPhone charges but won’t turn on, it could indicate a problem with the iPhone’s electronics. Let’s try to understand the reasons for the appearance of such symptoms and find out what actions we can take in this case.

IPhone Recovery

If iPhone charges but won’t turn on, you can try restoring it via DFU mode. To do this, we leave the smartphone on charge until the morning (so that it can take the maximum charge). In the next step, we need a computer with iTunes installed. We connect the smartphone to the computer, hold down the “Home” and “Power” buttons, press for 10 seconds, release the power button and, while continuing to hold “Home”, wait another 15 seconds. At this time, iTunes should report that it has detected an iPhone ready to restore. We confirm our intentions and wait for the results. Next, we try to turn on our smartphone.

We have already written about the procedures for restoring and flashing iPhone more than once in our reviews. use the search on the site and get the information you need.

What to do if iPhone 5 / 5s charges but won’t turn on

Although Apple gadgets are famous for their quality, even they sometimes fail, confusing their owners. There are times when the iPhone 5s is dead and will not turn on, even when connected to a wall outlet via the charger. What to do in such a situation? The main thing is not to panic and figure it out.

Repair iPhone

Your iPhone 6s won’t turn on or charge? Such a fate can befall not only the 6s model, but also any other models of smartphones from Apple. If the device shows no signs of life, does not respond to a long night charge and does not start even when you try to enter recovery mode, you need to contact the service center. Here experts will bring him to his senses. most likely, the motherboard is faulty in your smartphone, self-repair in this case is impossible.

iPhone is dead and won’t turn on while charging

Black screen and lack of response to button presses are common problems. In this situation, the main thing is not to panic and unwind the device yourself. Typically, the problem is a deep discharge of the phone or freezing iOS. Try the following:

1 Power charge can be discharged quickly at low temperatures. If you came from the cold and found a “black screen”, warm up the device. 2 Leave for 20 minutes connected to the charger. The iPhone should turn on by itself. This will not happen if the smartphone is completely discharged. 3 In this case, hold down the “power” and “home” keys for 10 seconds. For the 7th iPhone, you need to hold down the “power” and “volume down” keys. When the logo appears, stop holding the buttons down. Expect full iOS download. 4 If this procedure does not help, then turn on and off the mute switch before performing it. And do point 3 again.

If, after all the above has not yielded a result, we can conclude that there is a possible malfunction: iPhone, “charging” cord, “charging” head is not working properly, the throughput of the charger is low.

Causes of malfunction

IPhone has proven its reliability over the years. The manufacturer is concerned about the quality of its own devices, because a factory defect is virtually excluded, but allowed. Almost all malfunctions appear due to inaccurate handling of the phone, or with phones from the first parties. And also there are malfunctions in the software due to independent attempts to reconfigure the phone, resetting the factory options.

Among the most common reasons why the iPhone did not begin to cut it, there are:

• deformation of the nest or contamination on its surface;
• Broken power outlet or broken USB cable;
• Break of the loop contacts;
• Using a cheap Chinese device for recharging;
• “Glitch” firmware;
• Problems with the internal components of the iPhone: battery, power controller, motherboard.

Note! In case of dilemmas with a power controller or a battery, you will need to completely disassemble the phone. Do not try to carry it out without the help of others. you can destroy the main contacts, which will lead to the complete failure of the device.

iPhone is dead and won’t work. what to do?

Recently a friend asked for help. He said that his iPhone was dead and did not get it on charging. What to do in a similar situation? Personally, I’m a fan of the Droid operating system, so I went to the Web for answers. I “dug up” several methods that can help, but not always. For now, let’s take a look at the annotation for the iPhone.

Solution

Many users are in a hurry to deal with the problem without the help of others, trying to find out the cause and eliminate it. The lack of quantity and quality of knowledge sometimes leads to sad consequences.

There are only a few ways that you can try to implement without the help of others before going to the service center or calling the professionals at home.

Rebooting the Device Among all the tips given by almost all bloggers on the web, specialists at service centers (SC) consider it safe to completely reboot a mobile device. It is carried out if the iPhone does not respond to the connected charger. To do this, hold down the Power and Home keys with 2 fingers, after which wait 10-15 seconds.

If the company logo appears, the phone will start to boot, and the problem with the inclusion will go away. After waiting for activation, connect the charger to the socket and charge the smartphone battery one hundred percent.

If the phone does not work, it may be due to a software violation. To check and eliminate this deficiency, do the following (you must have a data backup):

• Connect the device to your computer’s USB cable;
• Wait for synchronization;
• Go to the “iTunes” program;
• Click on the “Restore” button and select the last backup.

After all the manipulations, the data recovery process will start, while the iPhone should restart and return to working state.

The solution to the problem with the charger According to statistics, almost all iPhone users save on buying a charger, if the original was lost or broken. This is not mind-boggling, so that the purchase of a “charger” from the manufacturer will cost 20 US dollars, and you can simply get a non-original component through “Aliexpress” at an affordable cost.

The solution to this difficulty is common. it is enough to purchase a unique device and put the device on recharge. If such manipulations have helped, you can continue to enjoy the work of a high-quality phone.

Important! Take a close look at the USB port on your PC that you used to charge your iPhone. It can be damaged or broken. To test this theory, it is enough to put the accessory on charging from an outlet with a voltage of 220 V.

Problems with charging devices are quite common, therefore, before trying to “hack” the iPhone with screwdrivers or throw off the options, check the performance of this attribute.

Changing components and modules When changing the “charger” or rebooting the accessory does not help, it’s time to contact the SC. Only there will the specialists carry out a full diagnosis and find out which spare part needs to be changed.

For example, a power controller or a rechargeable battery often fails during operation. To replace these parts, you need a complete disassembly of the “apple”, during which the cables are disconnected from the motherboard.

Important! IPhone repair professionals perform replacement parts using special tools. When using improvised means, you will completely “destroy” the iPhone.

And also a prerequisite for not turning on can be damage to the motherboard, which can only be replaced by professionals.

Care advice

Your iPhone will last for many years if you follow these tips for using the accessory. They are spelled out in the annotations for use, but almost all users do not pay any attention to the book attached to the news. Of all the manufacturer’s Комментарии и мнения владельцев, please note the following notes:

• Do not allow the device to get wet and do not leave it in a wet room;
• Do not leave the device near heat sources and in direct sunlight;
• Use a cover so that dust does not get into the connectors, clogging them;
• Do not drop or knock on the phone.

If you operate the device without a cover, then after a certain gap of time, you will need to clean the connector. To do this, use a soft-bristled brush.

Do not clean the connectors or speaker with a needle, toothpick, or wire. This will lead to a violation of the integrity of the parts and the need to replace them with new ones.

If it doesn’t help

I do not want to upset you, but if the listed ways of solving the problem are ineffective, most likely the reason is a hardware failure:

• The battery is “dead” completely. you will need to replace it at the service center;
• Charging cable damaged. try another one;
• The connector for connecting the power supply is broken. you will have to contact the SC to replace the connector;
• Critical failure of the basic “firmware”. no matter how annoying it may sound, you will not do anything at home.

Now you understand what to do if the iPhone is discharged and does not turn on even when the charger is connected. Try and be sure to write in the Комментарии и мнения владельцев which method was useful for you.

Common problem

Judging by the messages on the forums, a similar negative phenomenon is rare, but it does take place. And with this it is necessary to somehow fight. It’s great that in the overwhelming majority of cases, you can do without going to a service workshop. This means you can save a lot of money (yes, repairing the iPhone 7 and other models is not cheap).

Why won’t my Apple phone turn on after plugging in the power adapter? The prerequisites are as follows:

• The device was in a discharged state for a long time (from a couple of days or more);
• A software failure has occurred;
• The charging socket is damaged, or there is another hardware failure preventing the phone from being powered up.

Why iPhone won’t turn on while charging. iPhone is dead and won’t turn on. what to do?

If iPhone is dead and won’t charge. what to do?

Based on the listed reasons, we will consider effective solutions.

• When the battery is completely exhausted, connect an unusual “charger” to the iPhone, connect it to the mains and wait about fifteen minutes. At first, the screen will be black, but later an icon should appear indicating the start of the process:

Suddenly Afyon 6 does not start even after half an hour, but a “hint” appears on the monitor. they say it is necessary to connect to the outlet, it means do the required operation and wait at least four hours until the resource is 100% restored:

• If there is a software-type failure (the methods listed above are powerless), then you will have to resort to a “hard reset”. Hard Reset is simple, but after it all installed applications and data are deleted, that is, you get an iPhone with clean firmware.

It is necessary to hold down and hold two keys on the case. Home and Power (inclusion). If you have a newest iPhone that does not have a Home control, then instead of holding down the Volume control:

Do not let go until the “bull’s-eye” appears on the monitor. Traditionally, this happens in 20 seconds. The first start after the reset will last longer than usual, you will have to wait. And then immediately put it on charge, after that you can return information from iCloud.

Solving the difficulty with the charger

The last hope to get by with “little blood” is a breakdown of the charger itself. Find a 100% working charger and try to charge your device with it. Please note that both the power supply itself and the USB cable can break. With intensive (and not neat) use, the conductive cores of the cable are frayed or broken.

If a non-original Chinese charger or a cheap auto adapter was used, the power controller elements may become unusable. It happens that the phone stops recognizing the original charger, although it continues to charge with the Chinese counterpart. This is the first sign that the power controller will soon fail and will require replacement.

When to contact the service center?

In that case, if the reboot, cleaning the charging connector did not help, and it’s not a broken charger, we advise you to contact Apple certified service centers. This ensures that manufacturer-approved equipment is used for diagnostics and repairs, and that the parts are of high quality. Employees of such services undergo compulsory training and will be able to quickly determine the cause of the malfunction and replace the failed parts.

Why iPhone won’t cut in and charge

No one is safe from the nasty surprise in the form of a dark screen and unresponsive keys, even owners of reliable iPhones. Software failures, a breakdown of a charger or a standard USB cable are simply diagnosed and resolved without going to a service center. But the most severe difficulties with internal elements can cause a lot of headaches. We will carefully analyze the more common prerequisites for why the iPhone does not cut in, does not charge, what to do in this or that case, and when it is time to contact the service.

Checking the battery

When the apple device is charging, but does not want to start, then the battery may be the prerequisite for this oddity. The iPhone has a twist; this battery cannot be removed and analyzed. In this case, you need to put it on charge for the whole night and try to turn it on in the morning.

This is a common operation with batteries that are extremely discharged. After standing on the charge for half a day, the battery from time to time replenishes its own charge and gains a suitable amount of electricity. If the battery could be removed, then it would be worth trying to stir it up with a power supply unit or a “frog”. But, since our battery is not removable, we will have to wait. If your iPhone battery turns out to be removable, then the iPhone is not a real one.

iPhone does not respond to charging and does not switch

Apple phone owners are often faced with a situation where the iPhone will not switch on or charge. But do not immediately run to the service center or plan to replace the phone. It is entirely possible that a series of easy actions will help to cope with the situation without a visit to the SC. We will tell you how to exclude or confirm more frequent prerequisites that lead to the iPhone not responding to charging and will not turn on.

Solution

If the malfunction did not arise due to a hit or fall of the phone, then there is a great possibility that you can simply get rid of it. First, try the easiest ways to solve the problem.

iPhone is completely discharged and does not get it on charging what to do?

Good afternoon friends. The iPhone is completely discharged and does not work on charging, what should I do in this case? Basically, it is not necessary to start a panic. There are a number of ways to bring it back to life. But, before this, let’s think about why he suddenly finished obeying for you. Obviously, even if you forgot your own password on the iPhone and have no idea what you can do here, the energy in the battery must be saved. It can be announced that there are only a couple of circumstances due to which your device may not function.

First, your battery is fully discharged. 2nd. there was some kind of error in your iOS system. Let’s look at each of these cases.