iPhone is dead and won’t turn on what to do

Iphone is completely discharged and does not turn on on the charge what to do?

As you may know, the iPhone and iPad didn’t come to us from heaven but from Jobs’ garage. So like everything material in this world, these gadgets are not perfect in nature and can glitch and freeze. If your iPhone suddenly stopped turning on. You are in the right place.

In this article we look at the most common problems that do not turn on iPhone and try to find a solution for each of them. Now stop panicking and relax We’re going to fix it.

If you dropped your iPad from a 14-story building or washed your iPhone along with your jeans, this article is unlikely to help you. It should be clear that your device has been damaged badly enough. In this situation, it is better not to guess why the iPhone does not turn on, and immediately contact the service center.

• If you’ve drowned your iPhone in the toilet. Read this article
• Need to unlock your iPhone or get around Activation Lock. Read this article
• Iphone hung up on the “Slide to update” screen. Read this article
• Don’t know how to reset your iPhone?. Read this article

Suppose you don’t know the reason why your iPhone stopped turning on. Then let’s focus on the symptoms your device is giving you and then decide what you can do in each similar case.

Actually here are the most common symptoms of a problematic iPhone:

• Constantly black screen
• App is stuck
• Iphone doesn’t respond to button presses
• Apple apple is constantly lit on the screen
• Your iPhone is extremely warm

Let’s look at each of the causes in more detail, and list possible steps and solutions to turn on your iPhone.

Money-saving tips to fix iPhone 13 not turning on

Here are some money-saving tips to fix your “iPhone 13 won’t turn on” problem.

Charge your iPhone 13

If your iPhone’s battery dies, your phone won’t turn on. Although the phone shows a low battery, you won’t notice if you don’t use the phone.

In this situation, a dead battery could be a possible reason why your phone died and won’t turn on. So, take your charger and plug in your phone. After plugging the charger into an outlet, just leave the phone for half an hour. Do not turn on the phone immediately after connecting it to the charger.

Also, make sure the charger is not broken. Also, make sure that the cable or charging wire is in good condition.

Simple restart / forced restart of iPhone 13

You can try a simple restart or a forced restart to solve the problem of iPhone not turning on. Below is the procedure to forcely restart your iPhone:

Continue pressing these buttons until you see the Apple logo on the phone screen. If Apple logo appears, it means that your iPhone is turning on.

Restoring factory settings via iTunes (data loss)

An iOS hang-up prevents the iPhone from turning on. This is due to a malfunction of the operating system. In most cases iOS tends to be corrupted.

In this situation, the best way to solve the “iPhone 13 does not turn on” problem. Is to restore your device to factory settings. To perform this task, you’ll need to access iTunes through your Windows device or Mac. The procedure includes the following steps:

• Connect your iPhone to your computer, which runs iTunes.
• Itunes will then automatically detect your device in recovery mode.
• Next, iTunes will diagnose the problem and suggest either an update or a factory reset.

Since you need to restore your iPhone, select the ‘Restore’ option.

During this process, you will lose data that was previously stored on your device. It’s not really a loss, because otherwise you won’t have access to that data because your device hasn’t turned on.

What to do if the iPhone X/8/8 Plus is dead and does not turn on?

So, the first thing to do is to find the reason why your mobile device iPhone 8 Plus/8/X/7 Plus/7/SE/6s/6/5s/5 does not turn on. To do this, you need to connect it to the charger and wait for a while. Usually after 10-15 minutes, the phone will light up as soon as it gets the minimum battery charge. If the iPhone has been sitting in a discharged state for an extended period of time, it will need more time for the battery charge logo to light up. If it does not, and iPhone still does not turn on, then it is a software glitch which caused it.

To fix the system error, you can use the free program Tenorshare ReiBoot, which solves this and some other problems by entering and exiting recovery mode. A detailed description of what to do if your iPhone runs out of power and won’t turn on, below:

Download Tenorshare ReiBoot from the official Tenorshare website. Install it on your computer, then run it.

Connect your iPhone that won’t turn on to your PC with the USB cable. The program recognizes your device.

Now click on the “Enter recovery mode” button. Device will enter recovery mode. Itunes logo and USB cable will light up on screen.

When the “Exit recovery mode” button becomes active, click on it. The device will restart. After rebooting, your iPhone will be ready to go in stable mode. The software failure will be resolved!

Tenorshare ReiBoot can help you not only if your iPhone 8 is dead and won’t turn on. This tool can solve other common problems with iOS devices: after updating iOS 11, iPhone hangs on apple logo, iPhone hangs on black screen, blue screen of death, phone keeps rebooting, iPhone screen does not respond to user touch and others.

Tenorshare ReiBoot can be installed on Windows or Mac. The program is available for free download.

Problem Solution

If the malfunction is not due to shock or dropping the phone, there is a high probability that you can easily get rid of it. First, try the easiest way to solve the problem.

Wake your smartphone from a “deep” discharge

If the phone is discharged and then left uncharged for a while, then the smartphone won’t have enough power to turn on the screen. If there is reason to suspect that the battery is deeply discharged, then simply connect the phone to a charger and wait for 15. 20 minutes. Then, without unplugging it, turn on the smartphone. If the charging picture appears, then everything is fine, just wait until the iPhone has gained enough power to download iOS and continue working.

Reboot your device

Another standard step in solving problems with computer and mobile equipment is to reboot the device. Helps in two common cases. When the smartphone freezes and enters “save mode. The latter case often scares uninformed iPhone owners. When your smartphone is charged but has not been used for a long time, or has rarely rebooted, it will shut itself off without responding to the power button.

Rebooting an iPhone with a physical Home button (models 4 through 6S inclusive) is done with the power and home buttons. Press keys simultaneously for 15. 20 seconds. This action will send the smartphone to a forced reboot, restoring normal operation of the device.

A simple reboot may not help in the case of a phone firmware failure. The option to restore from backup with iTunes will help fix this problem. For this purpose connect your smartphone to the PC with the installed program and after synchronization choose the option to download the last backup. The app will restore the software and reboot your iPhone.

Fixing the charger problem

The last hope to get away with “minor repairs” is a failure of the charger itself. Find a 100% working charger and try to charge your gadget with it. Keep in mind that both the power supply itself and the USB cable may be broken. With intensive (and not careful) use frayed or break conductive wire cable strands.

If a non-original Chinese charger or a cheap car adapter was used, the elements of the power controller may be destroyed. It happens that the smartphone stops recognizing the original charger, although it continues to charge with the Chinese equivalent. This is the first sign that soon the power controller will fail and need to be replaced.

Changing components and modules

If all else fails, the problem is most likely a failure of the elements inside the iPhone. It is likely that the power controller, connectors and stubs, responsible for charging, or the battery itself is damaged. You can replace them yourself. There are dozens of websites with detailed instructions, but it is advised to contact an engineer from a service center. There is a high probability to damage something while disassembling the device or not to find the cause, as guaranteed to diagnose malfunction will be able only in the SC on the special equipment.

Problems with the charger

Often the reason that the iPhone is dead and does not turn on when charging is a defective cable. Users find kinks in the connection between the wire and the adapter. The electric current is not supplied to the device, so the discharged phone will not turn on. It is worth carefully inspect the charger. This will allow you to detect the breakage in time.

Connect the iPhone to another charger. If the phone turns on, the cable must be replaced, sometimes the failure cannot be detected with the naked eye. The cause can also be a faulty outlet, so do not panic beforehand. A trivial solution to the problem is often the right way.

Causes

The most common reasons that iPhone 6 does not turn on after discharging include a failure in the power supply circuit, microcontroller failure or bugs in the software. Troubleshooting associated with internal parts and the “iron” should be entrusted to professionals. It is possible to fix the program failure on your own.

The iPhone 6 is out of charge, and it does not turn on

If the smartphone does not respond to turn on when connected to the charger, there was a deep discharge or a problem at the operating system level. In case of a deep discharge of iPhone 6 you need to perform the following actions:

When the display shows the Apple logo, you need to release the keys;

Enable and disable silent mode if the smartphone does not boot up;

If the iPhone 6 does not turn on after a frost, what should the user do?

Go inside a warm room and leave the phone there for about 30 minutes;

After that you can connect iPhone 6 to the mains.

Apple electronics operate badly at subzero temperatures. Prolonged exposure to frost can cause a complete discharge of the device.

Iphone 6 does not charge and does not turn on

No charging due to several factors: broken battery, broken power/charging controller, or non-original cord or power adapter. The first thing to do is to check the cable. It should not have any breaks and breaches of integrity. Also make sure to use the original cord. If there is an additional charger, you need to connect iPhone 6 to it. If the phone started charging, the old cable is broken.

If replacing the cable did not help, the fault is caused by the battery or the controller. These parts can only be replaced at a service center.

Battery replacement prices:

Iphone charges and does not turn on

The main reason why iPhone 6 doesn’t turn on after charging is the battery. The problem could be caused by deep discharge, if iPhone 6 does not turn on after a long period of non-use. There are several ways to fix it:

Raise the level of charge to the bottom threshold. After that you need to connect the iPhone 6 to the mains for 6-10 hours to restore the charge. Then you can try to power on the smartphone.

If the previous method did not help, you need to change the charger and connect the phone to the mains again.

Enter DFU mode. You need to charge the smartphone for 6-8 hours. Install iTunes on your computer and open the downloaded program. Take the iPhone 6 off the charger and connect it to PC by holding the Power and Home buttons. Then release the Power key and hold the “home” key for another 15 seconds. You should get a notification on the screen, indicating that the smartphone is ready for recovery. You must press “recovery” and wait until the process is completed. After you can turn on your iPhone 6.

When the phone turns on, you need to observe it. If it runs out of power quickly, you may need to replace the battery. You should also check that you are using the original power cord. Non-Apple chargers may be designed for a different amperage, which negatively affects the iPhone 6.

Software Failure

When there is a failure in the program, usually only the apple is lit, and the device itself does not respond to turn on. You should perform a hard reset. To do this, hold Home and Power.

Causes

The most common causes of why the iPhone 7 does not turn on after a discharge, include a failure in the power circuit, microcontroller failure or errors in the software. Troubles related to internal parts and “hardware” should be entrusted to professionals. Program failure can be corrected by yourself.

Iphone 7 is out of charge and won’t turn on

If your smartphone does not respond when plugged in to charge, deep discharge has occurred or there is a problem at the operating system level. If the iPhone 7 is deeply discharged, you need to follow the steps below:

When the Apple logo lights up on the display, you need to release the keys;

Turn on and off silent mode if the smartphone does not boot up;

If the iPhone 7 does not turn on after a frost, what should the user do?

Go into a warm room and leave the phone there for about 30 minutes;

After this you can connect iPhone 7 to the mains.

Apple electronics do not work well in sub-zero temperatures. Long exposure to frost may cause a complete discharge of the device.

Iphone 7 won’t charge or turn on

Lack of charging is caused by several factors: broken battery, broken power/charging controller or non-original cord or power adapter. First of all you need to check the cable. It should not have any kinks or broken integrity. You should also make sure to use the original wire. If you have additional charger you need to connect iPhone 7 to it. If the phone started charging, the old cable is broken.

If changing the charger does not help, it is either the battery or the controller that is causing the problem. These parts can be replaced only in the service.

For battery replacement:

Iphone is charging and will not turn on

The main reason why iPhone 7 does not turn on after charging is the battery. The problem may be caused by a deep discharge, if iPhone 7 does not turn on after a long period of non-use. There are several ways to fix it:

Raise the charge level to the lower threshold. You need to connect iPhone 7 to the mains for 6-10 hours to restore the charge. Then you can try to turn on your smartphone.

If the previous method does not help, you should change the charger and reconnect the phone to the mains.

You can enter DFU mode. For this you need to charge the smartphone for 6-8 hours. On your computer, you should install iTunes and open the downloaded program. Take iPhone 7 off the charger and connect it to PC holding Power and Home buttons. Then release the power button and hold the “home” key for another 15 seconds. A notification should pop up on the screen, signaling that the smartphone is ready for recovery. Press “recovery” and wait for the process to complete. Then you can turn on iPhone 7.

Once the phone is turned on, you need to observe it. If charging ends quickly, you will have to replace the battery. You should also check that you are using the original power cable. Non-Apple chargers may be designed for a different amperage, which negatively affects the iPhone 7.

Software Failure

If the software fails, usually only the apple is lit and the device itself does not respond to power on. Then a forced reboot must be performed. To do this, hold down Home and Power.

Causes

The most common causes of iPhone not turning on after a discharge include a failure in the power supply circuit, microcontroller failure or bugs in the software. Troubleshooting associated with internal parts and “iron” should be entrusted to professionals. The failure in the program can be corrected by yourself.

Iphone is out of charge and won’t turn on

If the smartphone does not turn on when you connect it to the charger, you have a deep discharge or an operating system level problem. If the iPhone is deeply discharged, you need to follow the steps below:

When the Apple logo lights up on the display. You need to release the keys;

Turn the silent mode on and off if the smartphone doesn’t boot up;

If the iPhone does not turn on after a frost, what should the user do?

Go into a warm room and leave the phone there for about 30 minutes;

After that you can connect the iPhone to the mains.

Apple electronics do not work well at subzero temperatures. Long exposure to frost may cause complete discharge of the device.

Iphone won’t charge or turn on

Lack of charging is caused by several factors: broken battery, broken power/charging controller or non-original cord or power adapter. The first thing to do is to check the cable. It should be free of kinks and cracks. You should also make sure that you are using the original wire. If there is an additional charger, you need to connect your iPhone to it. If the phone started charging, the old cable is broken.

If replacing the wire does not help, the problem is caused by the battery or the controller. These parts are replaced only in the service.

For battery replacement:

Iphone is charging and won’t turn on

The main reason why the iPhone does not turn on after charging, is the battery. The problem may be caused by deep discharge, if iPhone does not turn on after a long period of non-use. There are several ways to fix the error:

Raise the charge level to a lower threshold. To do this, you need to plug in the iPhone for 6-10 hours to restore the charge. Then you can try to turn on the smartphone.

If the previous method didn’t help, you need to change the charger and reconnect the phone to mains power.

Enter DFU mode. You need to charge the smartphone for 6-8 hours. Install iTunes on your computer and open the downloaded program. Take the iPhone off the charger and connect it to the PC holding the Power and Home button. Then release the Power button and hold the “home” key for another 15 seconds. A notification should pop up on the screen indicating that the smartphone is ready for recovery. Press “recovery” and wait for the process to complete. After you can turn on the iPhone.

Once the phone is turned on, you need to observe it. If the charging runs out quickly, you will have to change the battery. Also check that you are using the original power cord. Non-Apple chargers may be sized for a different amperage, impacting on iPhone.

Software Failure

If there is a failure in the program, usually only the apple is lit, and the device itself does not respond to turn on. Then you need to force reset. To do this, hold down Home and Power.

Ways to solve the problem

What to do if iPhone 7 does not turn on? There are four ways to solve the problem.

Forced reboot

The quick solution to the problem is to reboot the smartphone. Hold Home and Power buttons with fingers, then wait 10 seconds. When this time passes, the smartphone logo will appear on the screen. The gadget will turn on, then plug the charger into the socket and wait for the battery to charge.

Connecting to the charger

Some iPhone owners save money on buying chargers. And no wonder. The originals are not that cheap, and a similar model is easily purchased on Aliexpress. Problems of this kind with accessories are common. So plug your phone into the original charger and see what happens.

Restore using the DFU mode

DFU mode is a special operating mode of iOS, which is used for updating and recovery gadgets. If an emergency occurs when the smartphone cannot update, use this method. If iPhone 7 Plus does not turn on, you must do the following:

• Start iTunes on your computer;
• Connect the smartphone to the PC using a proprietary cable;
• Turn off the gadget by pressing the power button;
• Hold down this button and press the volume down button for 10 seconds;
• Then release the power button, wait for 5 seconds.

Itunes will notify you when the smartphone is connected. Now click the “Restore” button in iTunes, wait for the operating system to start.

In case of difficulties, try to manually select and install the previously downloaded firmware. To do this, go to iTunes using the above method and select restore by holding down the Shift key. Now select the firmware file and confirm the selection.

Sometimes the Apple gadget refuses to go into DFU mode. You can tell this by a number of indications:

• The company logo is lit on the screen;
• Itunes icon appears on the display (the phone is in Recovery Mode, there are no items you are looking for).
• Itunes does not see the connected smartphone.

Experiencing these symptoms. Try switching to DFU mode again. Phone goes back to normal on its own after repairing.

What to do if none of the above methods help

If the above methods do not help, you can take the damaged gadget to the service center. Professional craftsmen easily fix such problems, and the cost to the owner of the device will not be as high as when buying a new smartphone.

If the problem is of a slightly different nature: the iPhone does not turn on and the screen is black, then read the solutions in the article.