Iphone Activation May Take A Few Minutes
Tip 4: restore iPhone
If none of the above helps, try turning off your iPhone, connect one end of the USB cable to the Mac, and do not insert the other into the iPhone yet, hold down the Home button and at this very moment insert the USB cable into the iPhone. If everything went well, iTunes will show the message “iTunes has found iPhone in recovery mode. You must restore your iPhone before using it with iTunes. ” Then click the Restore iPhone button and follow the instructions.
Do not know how to activate a purchased iPhone 4, 5, 5s, 6, 6s, 7 yourself, then this article is for you!
The main functions of the phone are receiving and transmitting calls. And only then all the other possibilities: social networks, games, movies, applications. For the safety of users, iPhone has a special activation procedure. As a result, the smartphone will be tied to a specific subscriber, which will complicate the actions of intruders in the event of theft or loss of the device. Using a personal ID code, you can track the location of the device and even block it remotely or delete important data, and synchronization with the cellular network allows you to optimize its work with the telecom operator.
Activate iPhone with an emergency call
Assumes turning on the iPhone, and when a greeting appears on the display, sequential pressing of the Home and Emergency buttons. Then enter “112” and start the call. After that, quickly press the shutdown button. Then “Cancel”. After the end of the call, the gadget will perform all its functions and work normally. This means that you have successfully activated your phone and can now control your phone.
The efficiency of the first one has not been tested by us, but you can try it. It definitely won’t get any worse.
Tip 3: use a working SIM
If you have a different SIM card and you are sure it works, try using it. When replacing the SIM card, you do not need to turn off the iPhone, just replace it, press the Home button and try activation again.
Another important note: the balance of your SIM card must be positive, and the amount on the account is sufficient for one SMS abroad.
This is not advertised anywhere, but this is how the problem with activating iMessage and Facetime is solved. We found that in order to confirm the activation of these services, the iPhone is apparently trying to send a technical hidden SMS to the Apple servers. A technical SMS is sent from your phone to a special number, so the balance on your SIM card must be positive and sufficient for such an operation.
Confirmed! Activation actually sends SMS, which is charged as “SMS to other countries”.
4.Turn on location services
Location services allow you to navigate, share your location with friends and find your Apple device on a map in case of loss or theft.
Iphone activation algorithm
During activation, the phone’s SIM card data is sent to Apple servers and the IMSI is checked. Thus, the binding to a specific mobile network operator is determined. If the verification is successful, the subscriber receives a cellular network activation code.
Activation must be repeated if the iPhone was reset to factory settings, all accounts were erased and content was deleted, as well as after an update in iTunes. If only the settings are erased, then you do not need to activate the phone.
How to activate an iPhone
When we receive a new iPhone, the first thing we have to do is activate the device so that we can use it.
And usually, we have to turn on the mobile phone with the SIM card. However, what if you don’t have a SIM card when you want to activate your device? Does this mean that there is nothing you can do at this moment? Absolutely not! Even if you don’t have a SIM card, you can still activate your iPhone easily.
If you would like information on how to activate iPhone without a SIM card, you can read and skip to the details below to try.
How to activate an iPhone
Having become the happy owner of a gadget from Apple, you will have to understand not only the system, but also understand how to activate it. Startup is required for the device to start working. The process is easier than it sounds, and the setup itself will take a few minutes. The user may be surprised by the number of lines and fields that need to be filled in completely. In the article material, we will tell you what to enter and choose in each of them. Follow the instructions below carefully, and if you do everything correctly, then there should be no problems. We will analyze all possible ways to activate a new iPhone.
The activation process may vary slightly. It all depends on the specific gadget model. But in general, the procedure is identical for every Apple device, and the instructions below will work for any model. If you are holding an iPhone in your hands for the first time and / or have switched to a device from the Android operating system, then we suggest reading this detailed guide and find out how to activate on a new device.
Activation on iPhone
To activate, you only need an iPhone, no more devices are needed. All you need to do is do the following:
- Insert the SIM card into the special tray. The slot is located on the side of the device, namely, on the right side (on very old devices, starting with the first iPhones like 2G, 3G, 3GS, the slot is at the top). The hole can be opened using the tool that comes with the device itself on the spread of cardboard paper. If you do not have this device at hand, you can use a paper clip (do not open the tray with sharp objects, such as needles, as this may break). Insert a paper clip or tool into a thin hole and remove the slot, then insert a SIM card of a suitable size (recall, these are micro or nano sizes);
- Launch the gadget. After you have inserted the SIM card, turn on the iPhone. To do this, you need to hold down the power button for a few seconds. When the branded apple icon appears, you can release the key. A welcome screen should appear. Press the Home button or pull up the shutter on iPhone 10 and above;
- Calibration of basic settings. The welcome screen does not leave much choice of actions: you just need to select the language in which all information on the phone will be displayed (application names, notification texts, system labels, and so on). The next step is to select your region of residence;
- Internet connection. It is best to use a wireless Wi-Fi connection to make the setup more stable. After selecting the region and language, the smartphone will check for available internet networks. If there is one, you will have to enter a password. In another case, you can use the mobile Internet if it was previously connected to a SIM card. To do this, click on “Use cellular network”. Both LTE and 3G will do. Important note! The iPhone cannot be activated if you use a gadget that distributes mobile Internet as a Wi-Fi connection;
- Configuring services and authentication. Wait for the sync to finish after the last step and proceed with the next settings. Some of them are optional and can be skipped by calibrating a little later.
- Set up Face ID (face recognition) or Touch ID (fingerprint recognition). In both cases, you will either have to place your face in the camera frame several times and perform a circular motion of your head, or put your finger on the “Home” button several times;
- Come up with a passcode. Initially, you are always prompted to enter a six-digit combination. The number of characters can be changed to 4 by clicking on “Password code parameters.
- Selecting the type of setting.
- Quick setup. If you are migrating from an old iPhone to a new one, or if you have another gadget in the ecosystem (like an iPad), then you can speed up the installation process significantly. It is enough to bring the device close to the new device. The only requirement is to have an update to iOS 11 or higher;
- Recovering from a copy of iCloud. Move “over the air” all data that was saved on a previous device from Apple. These are photos, records, notes, messages (it all depends on what you saved in iCloud). Select from the list one of the last synchronizations after entering your account data;
- Use the gadget like new. If you purchased an Apple device for the first time and did not use iTunes or iCloud services, then select this item and set it up as new.
- Create an account or log in. The next step is to enter your Apple ID login and password. If you already have an account, then just enter the required information. If you do not have an account, then click on “No Apple ID or forgot it?” It is better not to skip this important step, since Apple ID is tied to important services: Apple Pay, iTunes, iCloud and others. If you do not want to create an account right now, then select “Set up later in Settings” and then “Do not use”. Or come up with a username and password right now, additionally answering some simple questions;
- Configuring additional services. Optionally, if desired, the user can calibrate geolocation (determining the current location), set up the Siri voice assistant, True Tone function on iPhones 8, 10 and higher, agree or refuse to share device diagnostics reports with Apple, choose the interface display type, etc. It is not necessary to configure this, you can always find these services in the “Settings”;
- Last step. Press the button “Start work”.
Data recovery from backup if required
Everything is simple here: when completely deleting data, make a backup, and then, when setting up a new gadget, select “Restore from iCloud copy”. Log in with your ID and find the most recent backup in the list. Recovery may take several minutes, and the process cannot be interrupted!
Activation via iTunes
Another method of activating the “apple” device is to enable it for further work through the iTunes utility. The multifunctional program allows you to organize space, buy and download content, back up or delete data. It can be downloaded for free on the official Apple website. For the following instructions, you cannot do without a PC and a USB cable.
- Connect the USB cable to the computer (it is better to use the original one for smooth operation);
- The program should start automatically. If it doesn’t, turn it on yourself;
- Wait a while while the utility recognizes the connected gadget and connects to the company’s servers;
- On the left side of the screen, find the icon of your device and click on it;
- The program will ask you to log in to your Apple ID. Register or log in with your username and password. You can skip this step and create an account after complete setup, but, most importantly, do not forget to do this later;
- The next step is iTunes will offer to restore the backup or start the iPhone as new;
- Wait a while. The iPhone should restart. After that, setting up the phone is no different from the previous instructions.
Why activation is needed
As mentioned above, to activate means to make the very first turn-on if you just took the device out of the box and removed the protective film. Or just turn on, if the phone was flashed before or the settings were reset.
Activation is the initial setting of the gadget’s parameters, namely: language, region of residence, selection of a backup copy (if there is one: this is described below) and calibration of some additional functions and services. If you have already activated the iPhone, then some points should be familiar to you, otherwise. Read our detailed article to the end.
Activation is also required for the device to identify your cellular operator and register it in the network database. After the owner inserts a SIM card and turns on the device, the iPhone sends information from the SIM, namely, a unique IMSI (International Mobile Subscriber Identifier) code. In a matter of seconds, all data is analyzed, all information is confirmed, and it is also checked whether the subscriber can access the requested network in which he is located.
How the two terms “activation” and “Apple warranty” are related
Many users, who have picked up an Apple device for the first time, ask themselves the question, what does the guarantee matter when starting from scratch for the first time or again? The fact is that the activation process is accompanied by an automatic start of the warranty period from Apple. The warranty period does not start on the day of purchase, but from the moment the Apple ID account was created (or re-authorized).
Important note! The initial text “Hello” (Hello and other greetings in different languages) in no way signals that the device is new. This inscription appears regardless of whether the device is new straight out of the box or used with discarded content.
Use a working SIM card
Usually, problems with activation occur when the phone is tried to be activated without a SIM card. Insert a working SIM card into the iPhone and try to activate the smartphone again. If this does not help either, start the activation using the cellular network by turning off Wi-Fi. This solution helps most users.
Sometimes an activation error occurs due to the fault of the telecom operator, which for some unknown reason rejects it. I think many people remember what problems Beeline subscribers had to face when activating iMessage, although in this case we are talking about something else. Try inserting a SIM card from a different carrier and activate your iPhone. After that you will be able to use your previous number again.
Based on materials from osxdaily.com
When an error occurs, hold down the Home button until the bottom menu appears, and then click “Try Again”. You will be taken to the initial settings page and can try activating your iPhone again. Often, to get the desired result, you need to do this procedure 5-7 times.
How to fix iPhone activation issue
If you’ve ever reset all iPhone settings to factory defaults and then tried to reactivate your smartphone, you may well have encountered an activation error. It is difficult to understand the causes of this problem, since in this case it does not give any useful information on the iPhone screen, but only advises to contact Apple technical support. But since this process is quite long, you can try to fix it yourself.
Did you know that your iPhone always knows where you are? No, we’re not talking about geolocation in applications right now. Many iPhone and iPad users are unaware of the fact that their devices are constantly sending data about their location to Apple, and also save all the information on the devices themselves. It’s one thing if a person has nothing to hide at all, [.]
Despite the fact that Apple has been very active in developing Mac computers in recent years, offering super-cool updates almost every year, their front cameras seemed to be stuck in the late 2000s. The 720p resolution for the top models and 480p for the basic ones like the 12 ”MacBook clearly did not contribute to obtaining a high-quality picture. It is clear that there is no point in using [.]
The practice of beta testing fresh updates from Apple has been around for a very long time. Despite this, all these years the company for some reason allowed all owners of its devices to participate in the program, except for the Apple Watch. For some unknown reason, only developers could test the new watchOS assembly before the official release, and this opportunity was closed for ordinary users. However, at WWDC 2020, [.]
Iphone 5 activation error
Often after buying a new or supported Iphone 5 phone, there is such a problem as an error when activating Iphone 5. Why this happens and what to do about it, read below.
Iphone 5 activation error
The activation error can be manifested by several messages issued by your device:
- Your Iphone device failed to activate because the server is temporarily unavailable.
- SIM card in Iphone is not supported by the device.
- Your Iphone device cannot be activated and recognized for service.
- Itunes cannot check the device.
So, error when activating Iphone 5 what to do? The solution to these problems can also be several ways and options.
First, you can try restarting your phone. To do this:
- Find two buttons on the phone, the on / off button for the phone, and the Home button, which is in the middle of the bottom of the screen.
- Press these two buttons together and hold for 5-10 seconds until the phone turns off completely.
- Turn on your phone and check the effectiveness of your actions.
If this option did not work, and activation still has not occurred, then there is a possibility that the phone is not untied from Apple ID. In order to untie the phone, if it is supported, you need to contact the former owner of the phone and request login and password information to enter the Apple ID. If the phone is not tied, and the reboot did not work, then try connecting to a Wi-Fi network if your device is not activated via the cellular network.
If, as a result, nothing helps, then contact the service center or support service. You should not try to disassemble or assemble the phone yourself, or try to do something yourself at the technical level, since there is a possibility only to aggravate the problem.
Full use of such gadgets from Apple as iPhones, iPads and others requires an ID registration procedure. At that fertile moment when users know how to install.
While doing research on Apple’s iOS OS, one secret, and in many cases useful, feature can be discovered. Its essence is that it enables iPhone users.
The first reports that iPhones, regardless of where they were purchased, have a worldwide warranty, have led to the belief that a warranty case involves warranty repair, or.
The essence of the problem
Users started to flash the device with iOS 11.0.2. After flashing, they get error 0xE8000013. Here is one of the comments on our website (the spelling and punctuation of the author are preserved):
The error, by the way, is not new. A year ago, some iPhone 5S users were catching the same error on iOS 10.
Iphone activation failed after flashing. Error 0xE8000013
Today I found out (yes, I am a slop in this case) that many users have a strange error 0xE8000013 after flashing their device to iOS 11.0.2. Let’s take a closer look at the problem.
One of the possible reasons for error 0xE8000013 is not native Touch ID on the phone. But not always. This is an iOS 11 bug.
There is no definite solution. Recommendations found on the Internet:
- You need to plug the wire directly into the PC. That is, without using USB hubs.
- Try a different USB cable
- Disconnect all USB devices from the computer except the mouse and keyboard. Restart your computer and connect your iPhone to your computer.
The guaranteed solution was to rollback the system from iOS 11 to iOS 10, but the method no longer works since Apple stopped signing iOS 10.
If you have any information, some solutions, or you have such an error. Write comments. We’ll figure out. For now, to avoid problems, I recommend not updating your phone to iOS 11.0.2.
P.S. ATTENTION. Scammers were identified in the comments. Now he acts under the name of Glory, but he can write under any other. DO NOT send your money to anyone! Nobody can solve your problem remotely. DO NOT share your APPLE ID and password with anyone.
Now faced the same problem
I’m waiting for a new update
I hope apple will solve this problem
Congratulations, you have a brick
[News] Caution! Bricks can be caught when restoring iPhone with iOS 11
The first complaints about the error 0xE8000013, which occurs when trying to restore an iPhone from a backup, began to appear at the end of September. To date, no solution to the problem has appeared.
You decide to perform a hard reset (Settings. General. Reset) or restore your iPhone from a previously saved copy on iOS 11 or a test version of iOS 11.1 using iTunes. Any of the options will result in an error with device activation.
In common people you will receive a “brick” with an error 0xE8000013.
How common is the problem
To date, thousands of users around the world have encountered the “scouring” of iPhones. Apple representatives did not officially admit the problem.
Hello guys! This is a problem associated with the restored phones, namely, with the fact that they replaced the flash memory and did not register the native poppy address of the Wi-Fi bluetooth. So Apple does not recognize these phones.
It turns out that iPhone phones have become disposable? Then let the price be like a one-time product. All phones were once released by apple and were working, but due to their fragility and technical weaknesses they became REF. Even having officially bought a new phone. Dropped off nand and that’s it? To find out the data of the poppy addresses bt and vf is not possible if broke nand
Repair in an official service and there will be no problems !
Well, thank you! Just going to update. Stopped.
And when 11.1 comes out?
There is already the first public beta. It seems like the second should come out today.
I have been fighting for the 3rd day, there is no sense ((
updated to 11.1
Does not help. In the trash can
Take your time 🙂 I think Apple will revive your gadgets
Even if they warned, what and how, but there is no information, it’s a shame
A good mine with a bad game) Therefore, they do not warn. They want to fix it on the sly
Well, it seems as it is already known, it will not work, the brick remained in one word and not the phone
Hello! I have such a problem I updated the iPhone 6 to IOS 11.1.2 and did a factory reset, and now, when activating, Writes, your iPhone could not be activated because it could not contact the activation server. Try to connect your iPhone to iTunes to activate or try again connect over a cellular network in a few minutes. You can also try to activate via WI-FI, or contact Apple support
The phone has a network, but there is no network name, 3g, LTE shows, Wi-Fi is also there but I can not activate it, I did updates and restores everything reaches the end (software check, Unpacking Software, Extracting Software) on the phone a white screen is being installed. Until the end, a failure appears on the computer screen and all the error numbers are not there, please help me, I don’t know what to do anymore, epl says all sorts of nonsense, about the restored devices it says that if they did it in an unauthorized service, they replaced something, it might be a failure as someone did, it was necessary to bring it to the service, but I didn’t have it to be repaired, I don’t have to throw out the phone, help, whoever had such a problem, he fixed it, I’m glad for everything that tell me to do
P.S on my computer still crawls out the sim card is worth it or not, but I have a SIM inserted
Exactly the same story with me, you can’t do anything, just give it away for repairs, and then someone needs to fumble, you need to rewrite the memory there, and then it will work, and I think the repair will be more expensive than the phone itself, so the trash!
I understand that even devices with native Touch ID cannot revive? I just have an Ipad refresh and it has been dead for 3 days, today I was in the service, they said “epidemic”))) Well, let’s wait, the trash can is next to it)))
And my 5s on 11.02 constantly does not want to connect to wi-fi at home, does not accept the password, connects only after rebooting. Ipad doesn’t have this problem. Every time I come home I restart my phone. ??
It shouldn’t have been worth updating, just like me.
Yes, similar problems with wi-fi connection on iPad Air after updating to iOS11: it returns only after reboot. I thought that I was the only one. On the Apple forums, I have not yet found a clear solution. I would be grateful if someone did it and share some advice.
11.03 released it turned out to fix activation error?
I have such an error on iPhone 6s
my research showed that the phone turned off all communications with the outside world, and very limited with iTunes.
offers WiFi activation, but no WiFi icon. The module is dead.
if a SIM card is installed, it writes 3G and the signal level, but does not write to the operator (and how would he know the APN)
the phone recognizes but does not recognize the serial number. Although on the CH phone itself you can see and everything is ok.
Well, when you try to activate. Error 0xE8000013 and activation failed.
By the way, it was possible to roll back on 10.3.3, but it still does not activate now.
How did you roll back? Wasn’t there a mistake? Tell me how you rolled it back. I just downloaded the firmware ?
Yes, Sergey, I just downloaded the firmware 10.3.3 and through iTunes, according to the instructions in the article “Apple has again started signing iOS 10.3.3 for iPhone 6s. How to downgrade from iOS 11 “to Apple-iPhone.Ru
there is also a link to the firmware
DOBROGO SUTOK DNYA U MENYA 5S S OSHIBKOI AKTIVACII 0xe8000013 MOJETE MNE POMOCH ZDELAV TOJE SAMOE CHTO I DLYA VASHEGO 6S? NAPERIOD SPASIBO
Damn, and on the contrary, they told me to update the support service, yes 11.0.2 updated the error did not disappear, I was already in a panic, to be honest, a week has passed, nothing has changed today, I installed 11.0.3 nothing has changed in the service, they are fed promises that engineers are solving this problem, but from this it’s not easier like that !! This is how to understand finally what I have always loved for epl stability, and so on and now I have a brick that I don’t even know will fix or not say one thing !! This is a mess. They ruined their image seriously
And I have this that I updated it with the same error when activated, in short, I contacted them in St. Petersburg, they made me collect all the logs and send them to them for a month without a phone, and in short, they say that I am not the first who encountered this, but I ask them. And who would not have solved the problem. Are silent
People, why update at all ?? I have an iPad mini 3, aios 8 with something (even on the drum, what numbers are next). All perfectly
Good day! And I haven’t received push notifications for three days already. I didn’t install anything, didn’t change it. I decided to upgrade to 11.0.3. Nothing changed. Notifications come only if the program is open. In other words, I only see calls and that’s it.
So I updated and reset the settings. No words, what an evil I’m sitting, waiting for a decision
The same problem after updating IOS 11.3 dropped and now the brick.?
What to do with the brick now?
If completely brick-brick. Do a flashing through DFU mode.
I have been doing it for a week without activation from iPad Air 2. 11.0.3 error all the time, I try to activate it through aytyuns, but I write incorrect data, please try again later))
Try to flash the firmware again. In theory, the problem has already been fixed
Last night I was stitching, the same thing. And how to remove the firmware from aytyuns so that a new one can be downloaded
On the ipad mini 2 decided to perform a full reset, the activation flew.
Went to iTunes downloaded a new firmware, but I can not activate, it gives an error:
ipad “ipad” could not be activated because the activation information was incorrect. Please try again later.
Guys, can anyone already know the solution to the problem, please share.
Can I flash it for a fresh one according to the instructions? By downloading the firmware?
I also have an iPad 2 such a case of error 0xE8000013. But through i tunes I see the ipad, but there is no refresh button. Login fails gives “this Apple AD has not been used yet i tunes store”. Before that, there was a different ID, after changing the ID the problem began. How to flash? I am suffering for 4 days.
I have an iPod mini 3. Everything is the same. I’m disappointed with Apple.
Same problem. The phone was not being repaired. Touch id is native, robotic. We are waiting, as I understand it, a new update. Sad with apple ?
This is all the movement
Apple is certainly handsome. Faced the same problem on the Ipad Air 2. I bought it from a friend and did a complete reset and that’s it, hello brick. I hope that with the release of 11.1 Apple will be corrected.
Did not help. I just restored it with an update to 11.1 and still does not activate. I think a class action lawsuit against them could be?
You updated iTunes, I received an update yesterday, I haven’t tried it yet
I called support today. They said that for a billion epl phones, the problem of a couple of thousand calls with error 0x8000013 is unlikely to motivate techies to solve it in a short time. These are certainly not literal words of support, but the meaning is captured by this.
On the contrary, I would reassure you that there are too many references not to pay attention to them.
Today I turned to the service with the same problem. They said that it was boring to change the motherboard (touchpad) and for all this 125.
Don’t do it! Service breeds you 🙂
I generally have REF iPhone 5s, according to the standard out of the box it was 10.3.3, then I updated it to 11.0.3, sometimes started to freeze, and the like, did a rollback to 10k, and that’s all, activation failed, could not connect to the servers.
Rollback to iOS 10 hasn’t worked for a long time. Therefore, flash to the latest iOS 11.0.3 and everything will be activated for you
No, having a restored iPhone ref, it is he who blocks the activation of apple /
Did you really do it? I put iOS 11.03 a week ago, but it still does not activate.
To my delight, I have no such mistakes. Catching it on purpose is unlikely to work, so I give general advice. But to carry to the service and change the motherboard and touchpad, as advised above, is the last thing.
You understand, this problem is only with repaired iPhones, or Chinese refahs, I read here https://w3bsit3-dns.com/forum/index.php?Showtopic=846333st=1760
I reset the iPhone 5s, downloaded ios 11.0.3 and everything is exactly no activation, and everything is exactly 0xE8000013 in iTunes, and in the service they say they can start after the phone is re-soldered, the cost of repair is
more than half the cost of an iPhone))
Let’s write to the support team in bulk. This is a violation of the agreement on their part. In the United States, this is a responsibility. You can demand money or fix their jambs. I try different options. Unsubscribe
A really significant problem at first gave error 3194 when rolling back and then again connect to aytyuns and, like all 0xE8000013 in the server, they said to wait from the Chinese for a solution to this problem, they say today there were more than 50 people with such a problem
I’m just wondering? From where do people get this old. “Apple said” and all that. That there was no official statement from them. And in general, this is completely their jamb. That is, it turns out on IOS 10 everything was cool and did a full reset and everything was activated, and then a new firmware comes out and “half of the population” stops working gadgets. Don’t you think this is strange? And the fact that Touch ID stopped working for many on 6s (and for unmakers, who will say what it means is changeable, then I will say: if the button changes, then the print will no longer work initially! Check)
I have an Ipad Air 2, normal, not fixed and Apple has a serial number in the database and for some reason the activation has flown.
And in general, think about what you write, well, even if the phone was already sorted out, let it be fixed, but who cares. Yes, the sinister Apple company decided to punish such owners. Kapets, it’s funny. That is, they “outraged” their clients, and were not afraid to lose 20-30 percent of the profit, because everyone will switch to android. Ingenious.
Therefore, this is a real firmware bug, which they simply must fix. Considering that such a story has already happened to them with 5s when IOS10 was released.
And do not get fooled by all sorts of stories that you need to rewire the board and all that, this is the golden moment for the SC
90 percent of devices are not activated due to the wrong mac wifi address
the problem is solvable, contact ss there will help you.
So I already contacted ss apple, they told me that the phone could not be repaired, but the situation for me, however, like everyone else, worked fine on 10 ios, updated it to 11ios, worked for a week then started to turn off myself, I decided to reflash, reflash and all activation does not work, I have 5s
Hello everyone, let’s all zay…. So to speak apple collectively. I have been terrorizing the support of the result for 2 weeks now, not just a promise. I even sent diagnostics to them, and now they say wait for the engineers to solve your problem. And so it went 3 weeks!
Hello everyone! I’m in a panic! This morning I had all the photos of 1000 pieces automatically remotely, but there were no photos in the album recently deleted, I don’t understand why? My husband decided to restore and make a backup via iTunes updated, there is a chance return all the pictures, but the phone does not allow opening the problem, because of it it shows the window “The IPhone could not be activated. Because an unknown error occurred (0xE800013) Please try again later” how can this be understood and corrected to return IOS 11.
Read the problem above, everyone here is just like you, the problem is not yet solved