How to turn on iPhone 6s

Table of Contents

The smartphone is in “save mode”. there is nothing on the screen and the phone does not respond to buttons

Apple smartphones switch to “save mode” if you rarely restart it. What to do to turn on the iPhone 6s in this case? Press and hold the Power and Home buttons at the same time for 15-20 seconds. The smartphone should turn on.

iPhone 6s is low and won’t turn on. battery indicator is blank on screen

Naturally, after the phone is discharged, it will turn off. If an empty battery indicator appears when you try to turn it on, then you just need to put the smartphone on charge. It will not turn on immediately after that. you need to let him recharge. This can take up to an hour depending on how long the iPhone has been discharged.

When you plug in the charger, the screen will change. If this does not happen and the image with an empty charge indicator still hangs, then the problem is either in the faulty connector or in the charger. Try charging the device with a different charger. If it does not work either, then you need to go to specialists.

Software crash. smartphone freezes during startup

It happens that you are trying to turn on the iPhone 6s, and it freezes on the screen with the Apple logo or just gives a red / blue screen. Then you need to restore the firmware. To do this, you need a cable and a computer with iTunes installed.

  • Connect your smartphone to your computer and open iTunes.
  • Force restart the device by holding down the power and Home buttons. After 10 seconds, release the power button, but continue to hold “Home” until the recovery mode screen appears.
  • A window will appear in iTunes where you will be offered to restore or update the device. Select “Update”.

If after updating the iPhone 6s does not turn on, do not be alarmed: it just needs to be forcibly rebooted again by holding the power and Home buttons.

The smartphone is overcooled

If you use your iPhone in cold weather, it will quickly run out and turn off. For more information on this problem and methods of solving it, read the article “iPhone 6s turns off in the cold. What to do?”. The solution to the problem in this case is the same as in the past, but with one addition: before charging the phone, you need to let it warm up to room temperature. Let it lie down for half an hour, and only then charge it. If you plug in a cold iPhone, condensation may form and components may fail.

iPhone 6s won’t turn on: how to bring it back to life

There may be several reasons why the iPhone 6s is turned off and you can’t turn it on with simple methods:

  • smartphone is empty,
  • smartphone is overcooled,
  • the smartphone is in the “save” mode
  • there was a software failure,
  • damaged smartphone components.

Read on to learn how to turn on your iPhone 6s in each of these situations.

iPhone or iPad is frozen, does not turn on, or does not respond to buttons. What to do?

Don’t panic if your iPhone or iPad won’t turn on or respond to buttons when you try to turn it on. There are two ways to quickly bring it into working order, which we will tell you about.

turn, iphone

The first two reasons iPhone won’t turn on are not related to hardware or software glitches. Most likely, the smartphone is simply discharged and needs to be recharged, or it freezes, in which case a forced reboot will help.

iPhone or iPad is frozen, won’t turn on or respond to buttons (may be black screen)

A common problem. A fully charged iPhone (iPad) is frozen (the program is frozen) or has completely turned off. Pressing the screen or the side button, unfortunately, does not lead to anything and does not start the device.

Do not worry! In 99%, nothing terrible happened, the smartphone automatically went into the so-called “save mode”, this happens if you very rarely restart the device.

It should be noted that resuscitation methods may differ depending on the device model. so.

Your iPhone or iPad battery is completely discharged?

If your iPhone or iPad is discharged, connect it to the power adapter and charge it for 15 minutes, then try to turn it on without disconnecting from the charger.

If the battery is completely discharged, then sometimes after 5-15 minutes of charging, by pressing the power button, you can see an image with a lightning bolt and an outlet on the screen of a smartphone or tablet. This means that not enough time has passed since charging started. Wait a little more.

On the left is a screenshot of an iOS device that is not connected to the charger, on the right. it is charging:

If you have an iPhone 8, iPhone 8 Plus, iPhone X, iPhone XS, iPhone XS Max, iPhone XR, iPhone SE (2020), iPhone 11, iPhone 11 Pro, iPhone 11 Pro Max, iPhone 12, iPhone 12 mini, iPhone 12 Pro or iPhone 12 Pro Max

Press and quickly release the volume up button. Press and quickly release the volume down button. Then press and hold the side button until the Apple logo appears.

If you have an iPhone 7 or iPhone 7 Plus

Press and hold the Power button and the volume down button on the left for 15-20 seconds, after which the Apple logo will appear on the screen.

Why iPhone is charging but not charging?

These devices may appear for several reasons: the charging port of the iOS device may be dirty or damaged, the charging accessory may be defective, damaged, or not Apple certified, or the USB charger may not be designed to charge devices.

How the iPhone 11 Pro Max turns on?

  • Press and hold the volume up or down and the side button until the Power off slider appears.
  • Move the slider and then wait 30 seconds for the device to turn off.

What to do if iPhone is charging and won’t turn on?

If iPhone charges but won’t turn on, restore it via DFU mode.

  • Press the volume up button and release immediately;
  • Press the volume down button and release immediately;
  • Press the side button and wait for the branded apple to appear on the device display.

How to turn on iPhone 6 for the first time?

What to do to turn on the iPhone 6s in this case? Press and hold the Power and Home buttons at the same time for 15-20 seconds. The smartphone should turn on.

How to turn off iPhone without sensor and button?

How to turn off iPhone without sensor? You just need to hold down the lock and home keys at the same time, hold them for 4-5 seconds. Then the device turns off without confirmation. After that, you can simply turn on.

How to turn off iPhone 11 without sensor?

To turn off a new smartphone model without using a sensor, hold down the volume up or down button together with the off key. A slider will appear, after swiping to the right, the screen will turn off.

How to turn on on iPhone 6?

In order to turn on the iPhone, just press and hold the Power and Home buttons simultaneously for 15-20 seconds, after which the Apple logo will appear on the screen.

How to turn off iPhone x if the screen does not work?

How to Reboot iPhone X in Force Mode

  • Quickly press and release the volume up key;
  • Quickly press and release the volume down key;
  • Press and hold the side button until the smartphone turns off.
Read more:  Iphone 6 Not Charging Solution

Why AirDrop isn’t working?

If you are faced with the fact that AirDrop does not see the iPhone, you need to check the settings of the smartphone. Disable tethering if enabled on your device. Go to the “Settings” window. “Modem mode” and deactivate the slider.

How to enable Airdrop for 6 S?

  • Pull out the Control Center with a swipe. Pay attention to the section with Wi-Fi, Bluetooth, etc.
  • Press harder on this window If you do not have 3D Touch, then just hold down the window.
  • Open Settings. General. AirDrop.
  • Choose Only contacts or Everyone.

How to transfer photos from iPhone to Mac via AirDrop?

Using AirDrop on Mac

  • Open the file you want to send, then click the Share button in the application window. Control-click the file in the Finder window, then choose Share from the context menu.
  • Select AirDrop from the list of options.
  • Select a recipient from the AirDrop list:

How to enable AirDrop on ipad 2?

In the window that appears, open the “System Report” menu. Go to the Wi-Fi tab and make sure AirDrop is supported. There is a faster way to open AirDrop and make sure it works.

How to enable AirDrop on iOS 13?

How to enable AirDrop on iPhone or iPhone

  • Turn on AirDrop from Control Center, for which press firmly on the block with wireless interfaces, and then activate the switch of the same name.
  • Make sure that wireless interfaces such as Wi-Fi and Bluetooth are enabled on your device.

What to do if the iPhone won’t turn on and the apple is on?

How to Hard Reset iPhone without Button

  • Press the volume up button and release it.
  • Then press the volume down button.
  • Hold the power button and hold it until the screen goes out (the Apple logo disappears), and the device starts to reboot.

How To Turn On iPhone 6s & 6s Plus. How To Turn Off iPhone 6s & 6s Plus

How to sign in to your iCloud account?

Sign in to your iPhone, iPad, or iPod touch

  • Open the Settings app.
  • Click “Login to [device]”.
  • Enter your Apple ID and password.
  • If prompted, enter the six-digit verification code sent to your trusted device or phone number and complete the sign-in process.

How to set up iCloud on iPhone 11?

Go to Settings, click [your name] and select iCloud. Select the apps, such as Photos, Contacts, Calendars, and third-party apps, that you want to use with iCloud. Set up iCloud on other devices to sync content.

How to turn off iPhone 11 without sensor?

To turn off a new smartphone model without using a sensor, hold down the volume up or down button together with the off key. A slider will appear, after swiping to the right, the screen will turn off.

How to set up iCloud on iPhone 6s?

On iPhone, iPad, and iPod touch

IPHONE 6S WONT TURN ON QUICK FIX

  • Go to the “Settings” menu [your name].
  • Click iCloud.
  • Turn on the iCloud Drive feature.

What to do if iPhone won’t go to iCloud?

If you still need help signing in to iCloud, update your iPhone, iPad, or iPod touch to the latest iOS or iPadOS and your Mac to the latest macOS. For more information, see System Requirements for iCloud.

How to set up Internet on iPhone?

SIM cards of most mobile operators are sold with a connected mobile Internet: the user just needs to install the card in his iPhone, and access to the network will immediately be available to him. However, it is still necessary to know how to configure the Internet on the iPhone manually, otherwise, in the event of a system failure and deleting the network settings, the user will be left without access to a significant number of functions. neither checking mail, nor downloading applications from the AppStore will be available to him.

How to turn on mobile internet on iPhone?

First of all, you need to clarify whether data transfer is activated in the iPhone settings. To do this, go to the “Cellular” section in the “Settings” menu.

Then check the two sliders “Cellular Data” and “Enable 3G”. Both must be in active position.

If the “Cellular Data” toggle switch is not turned on, the iPhone will be able to access the Internet only if it is present in the Wi-Fi distribution area. Turning on 3G is also highly recommended. otherwise the smartphone will use the EDGE standard. The maximum download speed that can be achieved when connected to EDGE is 474 Kb / s, but you should count on 50 Kb / s. Needless to say, this is too slow internet?

Even if you switched the “Enable 3G” slider to the active position, this is not a guarantee that the gadget will work exactly via 3G. It all depends on the coverage area: if in the area where the iPhone is located, the connection is poorly received, most likely you will have to deal with EDGE.

It is very easy to find out which standard the data is transmitted through. just look at the top of the screen. Operator name can have one of two icons: 3G or E.

The second is evidence of data transfer via EDGE. Therefore, the letter E horrifies all lovers of fast Internet surfing.

If there is neither 3G nor E in front of the provider’s name, then the mobile Internet is not available. There are two possible reasons for the lack of a network: either the “Cellular data” slider in the settings is turned off, or the coverage is very weak.

After you check the toggle switches, you need to clarify whether the mobile connection settings are entered correctly. This is done like this:

In the same section “Cellular”, scroll down, find the subsection “Cellular data communications” and go to it.

Pay attention to the “Cellular Data” block. 3 fields must be filled in here: APN, username, password.

The following parameter values ​​are valid for leading operators:

As you can see, there are several easy ways to restart your iPhone if it freezes. This can be done on an emergency basis using physical buttons or you can schedule such an opportunity in advance by setting up the auxiliary touch menu.

Assistive touch

You can also set up a soft restart using the Assist Touch function. Assistive Touch adds an extra floating button to the screen with an extensive built-in menu.

  • Open the iPhone settings and move to the “General” section. Find the item marked in the screenshot with a frame.
  • In the “Accessibility” section, open the Assistive Touch area.
  • Using the switch indicated by the arrow, activate the auxiliary touch. To display the reset button on the main screen, you need to edit the top-level menu.
  • Using the area highlighted with a frame, you can change the number of simultaneously displayed options for actions. Select any of the icons indicated by the arrow and click on it.
  • In the list that opens, look for the item shown in the frame. Its selection as an active command to the assigned virtual button is confirmed by the appearance of a blue check mark in the line. After completing the described steps, the settings can be closed.
  • Now, if we open the Assistive Touch menu on the main screen, we will see the restart button we created. When you press it, the phone immediately starts to reboot. Thus, you can get rid of the need to hold physical keys and make the scheduled reboot process more convenient.

Power button

IPhones 6 and 6 Plus received larger screens compared to previous models. From 4 inches, it grew to 4.7 and 5.5, respectively. To preserve the ability to conveniently use the device with one hand, the power control has been moved to the right side face.

  • To turn off the smartphone, press and hold the indicated button for four seconds.
  • A virtual slider will appear on the screen, which must be moved all the way to the right. We are waiting for about ten seconds after which you can turn on the phone again using the side button.

Disable in settings

In case of malfunction of physical keys or lack of reaction to pressing, a software option for a “soft” reboot is provided.

  • Open the settings and go to the “Basic” section.
  • Scroll the screen all the way down. The last item, marked with a frame in the screenshot, allows you to turn off the device. When you click it, a familiar slider with a toggle will appear.

You can turn the device back on with a disabled button only by connecting it to an external power supply. If there is no power supply nearby, an external battery or laptop will do, even without iTunes installed.

How to restart iPhone 6

Smartphones produced under the “apple” brand are stable and durable. For ethics, they fell in love with users. However, no device can last forever. Sooner or later, any iPhone owner is faced with software bugs. Applications start to “slow down” or react incorrectly to pressing. Today we will figure out how to restart iPhone 6 when these symptoms appear.

Soft reboot

Turning off the smartphone for a while and then turning it back on is considered to be a “soft” reboot. There are two ways to do it.

Hard reboot

A hard option is provided in the case when the smartphone “glitches”. In this case, the device may “freeze” completely ceasing to respond to pressing.

  • To restart it to restore correct operation, you can simultaneously hold down the power key and the Home button, which has a built-in fingerprint recognition sensor.
  • The appearance of an “apple” on the screen means that the forced restart is completed and the procedure for starting the operating system has been activated.

The same can be done with the iPhone 6S and 6S Plus, which also have a physical Home button.

How to Hard Reboot on iPhone 6?

Standard hard reboot iOS device

  • iPhone or iPad must be turned on.
  • We simultaneously hold down two buttons. Home (round under the screen) Power (on and off).
  • Without releasing them, we wait until the iPhone or iPad turns off.
  • We continue to hold them until the screen lights up.

How to factory reset iPhone 6 with buttons?

  • Press and release the volume up button.
  • Press and release the volume down button.
  • Press and hold the side button until the Apple logo appears.
  • So to implement a Hard Reset, you need to hold down the volume down and Power buttons until the Apple logo appears.

What to do if iPhone 6 is completely discharged and won’t turn on?

Most likely, the smartphone is simply discharged and needs to be recharged, or it freezes, in which case a forced reboot will help. If your iPhone or iPad is discharged, connect it to the power adapter and charge it for 15 minutes, then try to turn it on without disconnecting from the charger.

Read more:  How to connect two pairs of Airpods to an iPhone

How to turn on iPhone 6 for the first time?

What to do to turn on the iPhone 6s in this case? Press and hold the Power and Home buttons at the same time for 15-20 seconds. The smartphone should turn on.

How to restart iPhone 6 / 6s / SE / 7/8 / X / 11

We tell you how to quickly and without harm to your smartphone restart your iPhone 5 / 5S / 6 / 6s / SE / 7/8 / X / 11 if it does not respond well to commands or some of its functions do not work.

It happens that your iPhone does not respond to commands or is in a half-dead state, when each press seems to be a terrible agony, due to constant system freezes. In this case (if this has nothing to do with the breakdown of the main components of the system), you need a way to urgently restart your smartphone in order to return it to the necessary functions.

In this short tutorial, we will show you how to quickly reboot your device without harming its fragile software.

When to restart your iPhone

Restarting your iPhone is the perfect way to solve the problem of smartphone freezes, app crashes, or display bugs. If you cannot use any of the functions of your smartphone, but you are sure that it is not broken, a reboot can be your real salvation.

But, if you are not sure that the components of your smartphone are intact and not damaged, then a reboot can help you make sure of this. For example, if the charging connector does not work for you, but you are not sure whether this is a system failure or external damage, then a reboot should reveal a flaw.

An emergency reboot completely restarts the system (most often without saving some data). It must be used very carefully and in exceptional cases when a regular reboot does not give the desired result.

Do not restart your iPhone unless absolutely necessary, or you risk damaging it. Ideally, one reboot for two to three days, if your device requires it. But, if the smartphone continues to freeze, we advise you to contact the service center and report the problems. Maybe your iPhone just needs cleaning or freeing up memory.

Also note that if your smartphone has been seriously damaged, then restarting will not help and you need to urgently contact the wizard.

Fast Restart iPhone

Fast system reboot is one of the useful features of your iPhone, which allows you to quickly restart the system if it starts to glitch, give errors, or if some components do not work for you, for example: a mobile network or some of the applications.

iPhone and iPad have their own reboot system, which is a simple key combination. By pressing them, you will cause an instant reboot, which will restart all the basic mechanisms of your smartphone.

In order to force a fast restart on your iPhone 6 / 6s / SE / 7/8 / X / 11 or iPad, follow the instructions:

  • Find the power button on your device
  • Hold it down until the Slide to Vigor Off window pops up
  • Swipe the command you want to disable
  • The device must reboot if you confirm the action
  • Remember to enter your PIN even if you always use your fingerprint or Face ID to access

Force restart iPhone

In cases where the smartphone does not fully respond to commands and does not respond to the call of the restart menu. you can use the emergency system reboot function, which works only on iPhones and differs in the way of calling for some models. With this, your smartphone should reliably turn off the power to all components and fully recover (if there is no mechanical damage or serious system failures).

How to fix Apple iPhone 6s that won’t turn on

How to Emergency Restart iPhone SE / 5S or Earlier

As we have already mentioned, there are some peculiarities of activating emergency restart mode, depending on the version of your iPhone. In order to restart iPhone SE / 5S or earlier, you need to follow these instructions:

  • Press the “Home” button, which is located on the bottom of the front panel of your device
  • Without releasing the “Home” button, hold down the top button
  • While holding these two buttons, wait until the screen of your device goes out.

Emergency restart iPhone6 ​​/ 6S

To urgently restart iPhone 6 or iPhone 6S you need:

  • Hold down the “Home” button
  • After a few seconds, also hold down the side power button without releasing the “Home” button
  • Your smartphone screen should reboot. the Apple logo should appear on it.

Force restart iPhone 7 iPhone or 7 Plus

Activating Emergency Restart Mode is different for the iPhone 7 and iPhone 7 Plus, so you need to follow these instructions:

  • Hold down the power supply (lock) button on your device
  • Without releasing the lock button, also hold down the volume down button
  • When the smartphone gives vibration. continue to hold the buttons until the screen goes out
  • Be sure to enter the password when activating the device, even if you always use fingerprint identification.

Emergency restart iPhone 8

To urgently restart iPhone 8, you need:

  • Hold down the power supply (lock) button, which is on your right
  • Without releasing it, also hold down the volume up button
  • When the phone vibrates, wait until the screen turns off completely and the Apple logo appears
  • Be sure to enter the password when reactivating the device.

Hard restart iPhoneX / XS / XS Max / XR or iPhone 11/11 Pro / 11 ProMax

With the release of new Apple smartphones, forced reboot mode has become more difficult, but you can still reboot your iPhone X / XS / XS Max / XR or iPhone 11/11 Pro / 11 Pro Max if you follow the directions below:

  • Quickly press and release the zoom button
  • Quickly hold and release the volume down button
  • Hold down the power supply (lock) button for a few seconds
  • Please note that all actions must be done as quickly as possible, otherwise the smartphone will not respond to commands.
  • In an ideal scenario, your screen should go out and then turn on again. The Apple logo should appear on it.

We hope our tips helped you fix the problems with your iPhone. Have a nice work. Also, do not forget that you can always contact the specialized iLab service center for help.

iPhone won’t turn on after being dropped

The absence of external signs of breakage (chips, cracks on the screen or case) does not mean that the fall went without consequences. Internal damage to the backlight layer of the screen, connector pins or mounts occurs at least often. So in the event that the iPhone 6 does not charge and does not turn on immediately after a fall or strong blow, then it is better to go straight to the service center to fully diagnose the device.

Breakdown reasons

The performance of a complex device depends on many factors. Even a minor hardware or software problem affects the smartphone’s performance. It is important to correctly establish the reason why the iPhone 6 does not turn on, and this article will help. Let’s start with the most common.

Turn on iPhone program

ITunes can help even if you just need to turn on your smartphone. For example, if the power button has failed. Usually, it is enough to connect the iPhone to the network or to the computer. the power supply automatically “wakes up” the device. But if the phone does not turn on, then launch iTunes and wait for synchronization. After detecting the iPhone, the program activates it.

6th iPhone hardware problems

The “hardware” of a smartphone can break even without good reason in the form of a blow or a fall. just because of age. Contacts are gradually thinning and breaking off, loops are frayed. The humid air gradually “burns out” the conductive tracks on the motherboard. It can take a long time to list the internal elements and possible options for their failure. There is only one verdict. it is only possible to diagnose and establish why the iPhone 6 does not turn on in a service center.

iPhone Shut Down and Won’t Turn On. Force Start

If the iPhone 5s has turned off and does not turn on, you should use the function that forces the smartphone to start. The method is relevant for those cases when the smartphone is frozen at some stage, perhaps only a black screen is shown, but the backlight is working, or after turning it off, the phone stops turning on. In this case, the procedure does not clear the device data, so it should be used initially. For each version of the iPhone, there is the same key combination, only in the latest 7th model it is different:

  • Hold down the Home button and the Power button at the same time. The hold time should be more than 10 seconds, usually up to 20 seconds. Then the Apple logo appears on the screen in the form of an apple. This option works for all versions except iPhone 7;
  • A separate, more familiar approach is used in the new version, you need to hold Power and the volume control, namely the volume down button. Similarly, you need to hold until the action on the screen begins.

The problem can be fixed by this method, but there are several additional methods.

IPhone 4, 5, 6, or 7 won’t turn on. power adapter

A fairly common problem that the iPhone 5s does not turn on is a power failure situation. The user, even when connected, may not see any reaction of the smartphone, but often they do not even suspect about such a banal solution to the problem as charging.

The iPhone owner needs to connect it to a charger, no matter what power source: 220 V, car or computer. Do not be alarmed if there is no immediate reaction. With deep discharge, for example, when the phone freezes, it takes time for the charging indicator to appear. It is worth waiting at least a few minutes, usually this time is sufficient. It is better to put it on charge for 1 hour, and then try to turn it on, do not forget about the previous method, it is still applicable now. Sometimes the process does not start, this can provoke various mechanical problems.

  • Check the cleanliness of the connectors, remove all kinds of foreign objects and dirt with a needle or brush;
  • Make sure that there are no kinks in the wire, probably there are interruptions;
  • Check the tightness of the contacts, perhaps the wire does not enter completely, then you will have to determine the reason for this;
  • We strongly recommend using original chargers. Lightning cables from Chinese manufacturers overheat during operation, may have insufficient power to charge or practically no power;
  • Sometimes the power or charging controller fails, then you will have to use the services of a service center.
Read more:  Wifi iPhone 4 not turning on

Why iPhone won’t turn on?

It is not worth thinking about why the iPhone 5 and any other model does not turn on for a long time if it was externally exposed to unwanted influences:

  • Perhaps the smartphone was dropped into the water, even a short immersion or rain can provoke a short circuit and refusal to work. If the phone was really drowned, you should not turn it on right away, on the contrary, turn it off and put it off to dry. After 1 day, try to turn it on, so the probability of restoring its work is higher, otherwise a short circuit will occur at startup and the smartphone will be unusable;
  • Mechanical damage. An iPhone, falling from a height, often takes a hit on the display, and the insides are less likely to suffer. There is no way out except to give the smartphone for repair;
  • Freezing. Batteries are afraid of prolonged exposure to frost, and at one point they lose all their charge due to a chemical reaction. You need to warm it up in your hands, and then try to start it, most likely you will have to charge it.

In these cases, it is possible to eliminate the malfunction only at service centers. There are a number of other reasons that lead to a freeze, some of which can be easily eliminated.

What to do if iPhone won’t turn on?

The iPhone is not an eternal device, although it breaks down a little less often than Android, but still it is not uncommon, then the question arises of what to do if the iPhone does not turn on. Gadgets often break down, freeze and stop responding to user actions. Often the reason is mechanical or external damage to the device, but this is not always the case.

How to turn on iPhone if it won’t turn on?

It happens that the iPhone charges, but does not turn on, especially often it reaches the logo and freezes at this moment or turns off. In this case, you can apply recovery mode. To use it, you need to have a computer at hand. It is highly desirable that the iPhone has already been connected to it beforehand, and the PC has been added to a trusted source of the connection, but this may not be useful.

  • Connect your smartphone and computer;
  • Launch iTunes;
  • Perform a forced restart of the device. Home (for the 7th version, the volume down button) and Power;
  • A message will appear on the computer screen allowing you to restore the operation of the iOS system, you should click on “Update”.

In this case, an attempt will be made to install the operating system without erasing the files. You may need to completely restore your iPhone to factory settings. Then in iTunes you will have to go to the main tab and click “Restore”.

Ultimately, if iPhone 6, iPhone 7, or any other version still won’t turn on, you need to contact technical support. They will remotely provide instructions on how to fix the problem, if this does not help, then they will direct you to the service center closest to you. This will mean that the problem is of a technical nature and the user is powerless here.

If the smartphone was used with care and charged with original chargers, then most likely it will be possible to restore its operation using the described methods. Otherwise, you will have to give the device to experts.

No votes yet! Be the first to rate this post.

Fill with liquid

Moisture on the phone or even flooding it with liquid is not uncommon. IPhone problems can begin not only when drowning it in a pond, but even when exposed to light rain. In this situation, the gadget may start to fail.

In this case, cleaning the device or component repair of the motherboard is highly desirable. In this case, it is important to stop using the phone immediately if moisture gets inside the device.

The solution to the problem is not entirely trivial, so it is recommended to seek help from a certified service center and avoid problems that may arise in the future.

Software glitch

The most common reason iPhone won’t start is a software glitch. To eliminate a software failure, you must do a hard reset of the device. To do this, simultaneously press and hold the power key and the Home key for 15 seconds. As a result, the device will reboot and will be available for normal operation.

If this does not help, then you need to try to put the device into recovery mode. To do this, hold down the “Power” and “Home” buttons for 30 seconds.

In a situation where such an elementary solution to the problem, together with a thorough charging of the battery, did not solve the problem, perhaps the reason for the non-working device is as follows:

  • the battery of the gadget is faulty (it needs to be replaced with a new one);
  • damaged adapter or USB-cable (you need to replace the adapter or USB-cable);
  • the cable connector is dirty (it is necessary to clean the cable connector);
  • low-quality (cheap) cable (replace it with the original one);
  • mechanical damage to the connector and other mechanical damage, for example, when dropped, wet, after charging in a car, etc. (you need to contact the service center);
  • marriage (you must contact the place of purchase).

It is also possible that the iPhone may not turn on after a firmware update.

There are three different scenarios, depending on when the failure occurred during the firmware update:

  • reflash the phone again;
  • replace the faulty NAND Flash. This is a memory chip that stores all the owner’s personal data;
  • replace the failed Nor Flash. This is the memory chip of the GSM module. All parameters of mobile operators are stored there. Without these parameters, the device will not be able to call.

What to do, iPhone 6 won’t turn on

Unfortunately, even with such a high-tech and reliable device like the iPhone 6 Plus, an unpleasant situation can happen.

Violation of operating conditions, an absurd accident, and sometimes a factory defect, can cause a smartphone to fail. One of the most common problems is the situation when the device does not respond to pressing the “Power” key.

Sooner or later, most iPhone users face this question. The problem related to the inability to turn on the iPhone. quite common. Each generation of iPhones has its own characteristics of this problem. The first thing to do is connect your iPhone 6 to the original charger.

Most often, the culprit of the breakdown is the “Power” button itself, which has a damaged contact pad or cable. The reason most often lies in the ingress of moisture into the case or in mechanical damage to the part caused by the phone falling. Also, quite often the refusal of the smartphone to turn on is due to a serious malfunction in the software or failure of the power system controller.

iPhone 6 could

In addition to battery problems, the iPhone not turning on can be attributed to human error. This is especially common when the phone is carried in a trouser

The device connector is clogged with dust and dirt, and the next time you try to charge it, the iPhone just breaks. This problem is not very serious, since any service center can fix it in a few minutes for little money.

Power and charging problem

If your iPhone 6 can’t turn on, it’s likely a power or charging problem. First of all, you should try to charge it. over, you need to connect it to the charger for at least 20 minutes from the adapter and 30 minutes from the workstation.

After that, you need to try to start the iPhone without disconnecting from charging. If everything is normal, the display will show a lightning symbol inside the discharged battery.

When the battery of an Apple smartphone is discharged to zero, after a short charge, when you press the power button, the display shows a picture showing a socket with a lightning symbol.

The way out of this situation is to charge the device for a longer time. In this case, the charging time must be at least 3 hours.

There are situations when the connector through which the phone is charged fails when using non-original charging.

It is very important to know how you can safely charge your iPhone 6 in your car, and even more important to follow these basic rules. This leads to dire consequences. At best, the iPhone battery needs to be replaced. At worst, it is replacing the power controller or repairing a failed power circuit.

How to create an email on Yandex for free? The answer is here.

Why and how to decide

There are a lot of reasons why the iPhone 6 turned off and won’t turn on.

Enlarged, they can be divided into the following:

  • complete discharge of the apparatus;
  • software problems;
  • hardware problems.

Software problems are easier to solve, in a situation with hardware problems, the solution is more complex and expensive.

Flawless appearance (without scratches and other visible flaws) does not mean that there are no problems with it.

Alternatively, one of several loops can snap off:

  • power loop;
  • display cable;
  • battery cable.

A more serious situation is associated with a violation of the soldering on the motherboard or damage to one or more microcircuits.

IPhone users may encounter a situation where the device has turned off and will not turn on. If you do not consider the simplest options, when the battery was simply not charged on time, then, most likely, the matter is in malfunctions of the boot data block of the operating system of the gadget.

This problem can be solved if you try to restore the partition by connecting the smartphone in DFU mode.

How to properly crimp an internet cable? Instructions here.

How to make your presentation on a computer? Create here.

Often, a hard reset will help to get the device out of this position, and if moisture or mechanical damage gets inside it, it is better to turn to professionals.