How to set up Vityas TV for channels. Service menu of TVs Vityaz, Horizon, Polar, etc

Vityaz TV how to configure the channels with a remote control?

To do this, you should press the “menu” on the remote control, then select “Channel Settings”. There you need to choose the option “Auto.building”. If you want to change the procedure for the location of the channels, then select “Sort”.

The owners of the television prefixes’ Vityaz ‘need to do the following: on the remote control, press the “ Mn’ button. On the screen to appear ” The Main Menu ”. Select the menu item ” Setting ”. Further. Point ‘Auto.Narrowing’ ‘. In the field ” Speed ​​(CS: Go/S) ” ‘. Dial 6875.

How to find out the TV code of the knight?

Enter the main menu by pressing the “blue” button of the remote control. Dial the code by pressing digital buttons 4, 7, 2 and 5 remote control. A service menu will appear on the TV screen.

To set up the TV “Vityaz”, you need to go to the service menu. To do this, you need to transfer the TV into the mode on duty, then press the AV button located on the front panel, then turn on the TV, holding the button.

How to set up channels on an old TV?

You need to find a menu with a line of launching the automatic search for channels and start the search. Usually it is called as follows: “menu”/“menu”. channel setting/channel. “auto.navigation”. The TV itself will clean the memory and write down the channels present in the cable network.

• They put the TV into the mode on duty, press the AV button on its front panel and, holding it, turn on the TV;
• On the inclined TV, the contacts of the connector XN1 are shortly closed.

How to set digital channels on a knight TV?

The owners of the television prefixes’ Vityaz ‘need to do the following: on the remote control, press the “ Mn’ button. On the screen to appear ” The Main Menu ”. Select the menu item ” Setting ”. Further. Point ‘Auto.Narrowing’ ‘. In the field ” Speed ​​(CS: Go/S) ” ‘. Dial 6875.

One of the simplest reasons why Avtopoisk does not find channels, there may be a non.compliance with the standards. First of all, check what broadcasting format is capable of taking equipment. The holder of the TV, catching digital TV through a regular antenna, must be ironically remembered by the abbreviation DVB-T2.

How to set up an old knight TV without a remote control?

To set up the TV “Vityaz“, you need to go to the service menu. To do this, you need to transfer the TV into the mode on duty, then press the AV button located on the front panel, then turn on the TV, holding the button. You can also simply close the contacts of the XN1 connector on the already included TV.

Why doesn’t the TV catch channels? The main reasons for such a malfunction may be an antenna that does not perform its main functions, or the TV itself. The first step is to exclude the breakdown of the antenna. The simplest option. Try it on another home TV.

Why is Samsung TV not looking for digital channels?

If the TV does not find the channels, check: whether the cable is damaged and whether it is tightly connected to the TV; Whether the antenna is correctly established and configured; Is the signal source correctly selected: cable or antenna.

• First of all, we connect your antenna to the TV nest.
• Next, take the remote control, you can also use the buttons on the front panel.
• Press the TV menu button, usually this button is indicated as menu.
• Find the channel section, usually be under the Six icon.

The history of the development of the enterprise

In the spring of 1976, the Vitebsk television plant was created. A year later, the first color TV “Vityaz-722” appeared. During the year, the enterprise collected 500 copies. Already during the year, the volume of production increased 100 times and amounted to about 50 thousand copies. Another year of work allowed to double the volume of production. Already in 1884, a half.billion TV got off the assembly line. It took another 4 years to reach a line of 1 million.

In August 1985, the production of integrated modular models began. One of the first was the model “Vityaz C381D”.

By 1989, the enterprise became self.sufficient. It was renamed the Vityaz production association. In addition to the release of TVs, the company began to engage in other activities. By 1990, the production of medical equipment began. A year later, a wood processing workshop opened.

Much attention at the enterprise was paid to quality. For this, its own certification workshop was opened. It happened in 1991.

The network of branches grew. They appeared not only in Belarus, but also in the neighboring countries of the Baltic states, to Ukraine and by 1993 more than 70 branded shopping centers in the CIS countries were opened.

Since 1995, TV production has been carried out using monoshassi of its own manufacture. In 1998, they began to assemble an analog digital TV “Vityaz” (37-54 centimeters diagonally). Within a short time, the company has mastered the production of more than 30 models. Their size was increased to 34-72 centimeters (14-29 inches).

In 2002, models with an absolutely flat screen appeared. It was the Vityaz TV 54 centimeters diagonally. By 2007, the size of the kinescope of individual models has already reached 42 inches.

Is it difficult to configure TV correctly? I need the help of the master?

To achieve the correct display of the picture is no more difficult than setting up channels. It will take no more than 20 minutes of your time. In order for your TV to delight your eye, you only need to fit the image settings so that the test pictures are correctly displayed on the screen. How exactly it should be “correct” you will see below. The test pictures are selected by experts so that after setting you can enjoy any scenes by brightness, color, clarity and contrast.

Article in the topic: How to display a computer screen on Windows 7 TV

Repair and adjustment of TVs “Vityaz 37/51/54 CTV 6612/6622

So in this article we will examine in detail all aspects of the settings, both in the general case and for TVs from specific manufacturers. It is worth noting that there are various types of digital television. All proposed schemes relate to the cable “numbers”.

Click “Start scanning automatically”. After completing the search, the TV will show the list. You can also see it in the “DVB-C” menu. Important! LG TVs have the function “Automatic channels update”. Disconnect it, otherwise the TV will be discarded from time to time.

Setting up the AV receiver

The setting process is simple. It can be stepped by step in the form of the following stages of action:

• Turn on TV and receiver;
• Activate AV mode in TV;
• Enter the receiver menu;

TV Vityaz Astra 21 Channel Settings

To receive digital TV, you must have a TV with support for the DVB-T standard and compression format MPEG-4 AVC/H.264. If the TV is analog, it is necessary to purchase a console (SET-BOX), which connects to the TV and supports the above standard. The prefixes for receiving digital TV produces the CNC “Production of telecommunication systems”. You can also buy a Polish prefix (I don’t remember what it is called, you can look for on the internet), it was cheaper than the producer “Vityaz“. In addition, you need a television decimeter antenna. In Belarus, you can buy antennas: “Delta”, “Atiag/b-7.2 “,” Atiag-5.2 “,” Atig-5.2.21-69.one”.

To do this, go to the setting point (confirm the choice of “OK” key on the remote control). Go to the channel.

When the TV is turned on, the FU1 network fuse checks the serviceability of the network filter elements, the FU401 fuses and the transistor VT402.

When you turn on your TV, there is no image, but the sound works? Problems may be due to two reasons:

If this is a SVP module (extends as a computer cd drive tray), then it is very simple: for each channel button there is an appropriate setup regulator, when the rotation is rotated, set up for the desired program.

How to set up the TV “Vityaz

We are at the final stage of digital television settings. In the window that appears, we find the point “Search mode”, several options will appear, we need a “full” item. Click and fill out all the fields specified below.

When setting up TVs, the knights are not fixed channels? You found the channel that you searched, installed it, spent time, and after repeated turned on it suddenly disappeared. By repeating the procedures once, you understand that this is a useless activity, and there is no time left for rest, and your favorite movie has passed. What to do with such an unprofit? This question is asked by users who have got into this situation. The reason for this problem lies in the device for preserving memory, the incorrect work of which leads to this incident. Follow your device, otherwise you will have to contact a specialist.

In the section, we choose the countries we put “Finland”. In the next window. “cable”, then “installations”.

Repair and adjustment of TVs Vityaz 37 51 54 CTV 6612 6622

Your preferred settings and data after rebooting the TV will not be lost.

When the TV is turned on, the FU1 network fuse is burned out

Check the serviceability of the elements of the network filter, straightforlers of the FU401 fuse and the transistor VT402.

The TV does not turn on, the network fuse is in good

Check the serviceability of the elements R404, R405, VD402, VT401, FU401, D401, C409, C413. Also check the integrity of the windings of 1-6 and 3-4 transformers T401.

There is no image stabilization when the network voltage changes

Check the elements VD402, VD403, VD405, C409, C413, as well as the D402 opotron and the D401 chip.

The TV turns on. A thin horizontal strip is visible on the screen

Check the elements of the nutrition circuit of personnel coils, pay special attention to their soldering. Then the oscilloscope is checked by the presence of personnel sawn impulses on the. 1, 2 chips D301, if they are absent, replace the D102 chip. Control the voltage to the. 3 (14 c) and. 5 (27 c) d301. If faulty elements have not been detected, they change the d301 chip.

The image is reduced vertically

Check the elements R311, C312, C313, the presence of voltage 14 V is. 3 chips D301. If the faulty element is not detected, the D301 is replaced.

On the screen you can see the lines of the reverse of the beam, and the inversion is also observed from above

Check the serviceability of the elements VD301, R303, C304.

Check the operation of the D102 microcircuit, transistor VT101, passage of signals from tuner to D102 (binding. 48, 49).

Check the elements of the output cascade of a lowercase scan: transistors VT301-VT303, transformers T1 and T302, as well as the passage of lowercase pulses from the withdrawal. 40 D102 Douthzosis.

There is no memorization of user settings data

Replace the D101 chip, having previously rewritten the initial (factory) data into it.

Service adjustment

Transfer of TV into service mode can be implemented in two ways:

• They put the TV into the mode on duty, press the AV button on its front panel and, holding it, turn on the TV;
• On the inclined TV, the contacts of the connector XN1 are shortly closed.

The list of parameters of the service menu is given in the table. 12.

The history of the development of the enterprise

In the spring of 1976, the Vitebsk television plant was created. A year later, the first color TV “Vityaz-722″ appeared. During the year, the enterprise collected 500 copies. Already during the year, the volume of production increased 100 times and amounted to about 50 thousand copies. Another year of work allowed to double the volume of production. Already in 1884, a half.billion TV got off the assembly line. It took another 4 years to reach a line of 1 million.

In August 1985, the production of integrated modular models began. One of the first was the model “Vityaz C381D”.

By 1989, the enterprise became self.sufficient. It was renamed the Vityaz production association. In addition to the release of TVs, the company began to engage in other activities. By 1990, the production of medical equipment began. A year later, a wood processing workshop opened.

Much attention at the enterprise was paid to quality. For this, its own certification workshop was opened. It happened in 1991.

The network of branches grew. They appeared not only in Belarus, but also in the neighboring countries of the Baltic states, to Ukraine and by 1993 more than 70 branded shopping centers in the CIS countries were opened.

Since 1995, TV production has been carried out using monoshassi of its own manufacture. In 1998, they began to assemble an analog digital TV “Vityaz” (37-54 centimeters diagonally). Within a short time, the company has mastered the production of more than 30 models. Their size was increased to 34-72 centimeters (14-29 inches).

In 2002, models with an absolutely flat screen appeared. It was the Vityaz TV 54 centimeters diagonally. By 2007, the size of the kinescope of individual models has already reached 42 inches.

What difficulties may arise

There are times when it is not possible to configure the DVB T2 reception. If there is such a problem, you must make sure that there is no damage on the antenna. If it is whole, you need to check the direction. The antenna should be directed towards the tower. It is also necessary to install it on the street, if you put indoors, this will block the signal. If the user does not know where exactly the tower is located, the torsion of the antenna will help. It must be moved very slowly and smoothly. As soon as the antenna comes into contact with the tower, the device will work.

Attention! There are errors in the process of automatically searching for channels. For example, the receiver found few channels, or did not find them at all. It will help manual search.

There are also cases when the TV found channels, but their quality show is very bad. So, the antenna is turned towards the tower, but the contacts with it are bad. Try to move it a little. Such a problem can occur in bad weather.

Frequently asked questions about setting up analog channels

Sometimes, in the process of setting up the channels, certain questions may arise, some of which are considered below.

How to set up channels on a TV without a remote control?

The process of automatic and manual setting in this case is similar in a similar way, but for access to the TV menu, buttons located directly on its case are used:

If there are no such buttons, you need to purchase a remote control.

How to set up channels on an old TV?

In the absence of the menu, the channel tuning is carried out by special regulators, which can be located under the switching buttons or on the back side near the antenna connector. In addition, on old domestic televisions such as “electron” or “ruby” and portable automobile TV receivers, switching ranges are provided using jumpers, sliders or buttons. Setting television channels for such devices is performed only with hands.

What to do if the setting of the channels is lost?

If you configure the channels in automatic mode, try starting a manual search. With repeated channels failure, the reason should be sought in a bad broadcast signal, a faulty cable or a tap breakdown. Read more:

If you purchased a new TV, replaced the cable television operator or the type of broadcasting, then the first procedure that you have to encounter is the setting of TV channels on the TV.

Depending on the method of receiving the signal, three main types of broadcasting are distinguished:

• etheric. broadcast from the TV tape is transmitted to the usual antenna;
• cable. channels from the operator’s distribution unit are transferred to the apartments of subscribers with the wired method;
• Satellite. the signal from the satellite is transmitted to the parabolic antenna (plate) and converted by the receiver.

In turn, etheric and cable television can be analog and digital. The second is characterized by higher image and sound quality, but it may require additional equipment in the form of a digital console (tuner) to view it, especially when it comes to an old TV model.

Within the framework of this article, automatic and manual setting up analog channels on the TV is considered (for cable channels everything will be identical).

Is it difficult to configure TV correctly? I need the help of the master?

To achieve the correct display of the picture is no more difficult than setting up channels. It will take no more than 20 minutes of your time. In order for your TV to delight your eye, you only need to fit the image settings so that the test pictures are correctly displayed on the screen. How exactly it should be “correct” you will see below. The test pictures are selected by experts so that after setting you can enjoy any scenes by brightness, color, clarity and contrast.

There may be a situation when there are connectors on a digital tuner and a TV for receiving AV, but they do not join among themselves. What to do in this case?

Here are just some scenarios for using such adapters:

• If the new prefix mainly supports the HDMI standard output, use the converter on RCA. Some quality loss is inevitable (for example, high.clay channels will not be shown), however, the signal will correctly decompose in three old directions on the video sequence and sound for the right and left dynamics.
• If a plasma or liquid crystal TV (“Sony”, “ONIDA” and others, released in the late 90s-early zero years) is used, the old VGA video system can be installed there. For such cases, HDMI-VGA adapters exist and are actively sold. However, when using them, you need to remember: for transmitting sound to the TV TV, an additional wire is additionally needed (usually 3.5 mm jack).
• Problems are possible with SCART and S-VIDEO compatibility. In this case, the adapter is also used. Most models at the same time support the exit to the triple tulip RCA.

Advantages and disadvantages of connecting a digital TV without a receiver

Modern TVs make it possible to watch analog and digital television without a prefix.

This gives the viewer several advantages at once:

• No need to buy a receiver.
• The TV can be hung and not worry about the placement of additional equipment.
• The latest Smart models have much more functional than the prefix. For example, for Samsung Smart-TV you can install the OTTPLAYER application.
• Electricity savings.

These advantages will positively be appreciated by lovers of available TVs who want to view television programs in normal mode, and do not have high requirements.

Now about the disadvantages that are smaller, but they are more significant:

• Limited access to digital TV. The air antenna catches only 10 (20) television channels, and their increase in the near future is not expected. When using cable television, the situation is no better, t.to. The provider independently forms tariffs. They are not always suitable, and to unlock a particular paid channel you need a card that only the receiver reads. In the best case, you can choose the tariff “On interests” (sports, cars) or “family”.
• The inconvenience of the location of the channels. During direct connection, digital and analog television channels are placed together. When the receiver is used, all digital broadcasting programs are taken to a separate TV channel, and switching between them is already performed from the prefix.

Therefore, you need to decide. use multiplex or cable television. However, often the choice does not depend on the tenant and one of two is already present in the house.

Advice! Do not rush to buy a TV. It is possible that only cable television is available and to obtain all functions you will need to purchase a receiver that is suitable for an old TV.