How to set up touch ID on iPhone

Table of Contents

Touch ID on iPhone does not work correctly: reasons and how to set up

touch, iphone

Why Touch ID doesn’t work well on iPhone

As our practice shows, this problem rarely comes to hardware repair. In most cases, the issue can be resolved by setting up iOS. The touch ID fingerprint is configured the first time you start iPhone. Not all users make this setup with full responsibility. In most cases, it is done quickly, superficially. When scanning a fingerprint, the phone does not hold the same way as it does with subsequent use. Therefore, the reading of biometric data is incorrect, which causes a failure and the system requires you to enter the Apple ID password. A perplexed user runs into the Apple Lab with a “broken iPhone” creak. But you can solve the problem without leaving your home. Below we will tell you how to do it.

Touch ID does not work well, how to set up

The fingerprint sensor in the iPhone appeared in 2013 and has always accompanied and accompanies the models iPhone 5S, iPhone 6/6, iPhone 6S / 6S, iPhone SE, 7/7, 8/8, iPhone SE 2, as well as iPad Mini 3, iPad Mini 4, iPad Air 3, iPad 2017, iPad (2018). The Touch ID sensor was replaced in 2017 by Face ID. However, Face ID has not completely supplanted the Touch ID sensor yet. It is present on iPhone SE 2, iPad and iPad mini.

The Apple Lab service center is often contacted by users with the problem of a poorly responding fingerprint sensor. In this case, most often we are talking about relatively young models, where the sensor is built into the touch button Home.

How to set up the Touch ID fingerprint scanner on iPhone and iPad

If the identification sensor does not work well on an iOS device, you need to do the following:

How to Fix Touch ID Not Working/Unable to Activate Touch ID on This iPhone/iPad (4 Ways)

  • Go to “Settings”, “Touch ID and Passcode”.
  • Here, all user biometric data will be referred to as “Finger 1” “Finger 2” and so on. We delete all existing prints.
  • To do this, select the existing print and click “Delete print”.
  • After that, select “Add a fingerprint”.
  • Now, before starting to scan a new fingerprint, hold your iPhone or iPad as you would normally hold the device while unlocking.
  • Then go through the standard procedure for taking prints:
  • two prints of the thumb of the right hand;
  • two prints of the left thumb;
  • once the print of the index finger of the right hand (for right-handers) and left (for left-handers).

Thus, biometrics are removed for all unlocking options. If you wish, you can experiment and find the most optimal options for yourself. Reconfiguring Touch ID solves the problem of a poorly responding sensor, but it is not a panacea. Sometimes, in order to restore the sensor to work, it is enough to update iOS or restart the phone.

If none of the above methods helped to solve the problem, then come to us, to the Apple Lab service center.

Clean and dry the Home button

Make sure your finger is dry and clean and the iPhone fingerprint reader is dry and clean.

For your finger, you can wash your hands and dry it.

For the Home button, you can use a lint-free cloth to erase anything that might interfere with Touch ID recognition.

Downgrade iOS

The newest one may bring you more features, however the latest iOS version doesn’t always work well on all iPhone models. The battery drain defect on iOS 12 makes many regret the iOS update. So while the iOS update is not working, you can try to downgrade the iOS version.

Sounds like only experts can downgrade iOS easily, right?

No, actually. You can also perform iOS downgrade task using software.

Aiseesoft iOS System Recovery is an iOS system recovery tool that fixes many system problems like iPhone stuck, black screen, Apple logo, start up loop, etc. Besides, it can update your iPhone to the latest version or go to any version iOS on this device. supports.

  • Fixed iPhone Touch ID Not Working Caused by iOS System Issues.
  • Scan iPhone and Extract Data from Forgotten iPhone and iPad Passwords.
  • Update iPhone to the latest iOS version or return iPhone to a supported version.
  • Compatible with iPhone 11, 11 Pro, 11 Pro Max, XS, XR, X, 8, 7, 6, 6, 5, 4, iPad Pro / Air / mini, etc.

Connect your iPhone to your computer with a USB cable. Just remember to press the “Trust” button on your iPhone the first time you connect your iPhone to a computer, which will allow that computer to manage your iPhone’s data.

Correct your iPhone information from category, type and model if the information is incorrect.

Then select the iOS version you want to downgrade and click Next to start downloading the firmware and downgrading iOS.

Then you can use Touch ID to see if your Touch ID can work fine.

Turn Touch ID on and off

Touch ID. these are the settings of your iPhone and iPad. You can disable and enable Touch ID settings to unlock iPhone, Apple Pay, iTunes and App Store.

0 solutions to fix not working Touch ID

Update iOS

Each iOS update will bring you new features that you won’t experience. Meanwhile, the new iOS update will fix some bugs sooner. Keeping your iPhone updated will help fix Touch ID not working on your iPhone.

On your iPhone, click Options General Software Update Download and Install Latest iOS 15/14/13.

Generally speaking, the iPhone will automatically give you an update notification and you just need to accept it and your iPhone will be updated automatically.

Restart iPhone

Looks like restarting iPhone. it is a one-stop solution to solve almost all iPhone problems.

To restart iPhone SE, 6s Plus, 6s, 6 Plus, 6, 5c, 5s, 5, 4S, and 4: Press and hold the Power (Sleep / Wake) button on the top or right edge.

To restart iPhone 7, 7 Plus, 8, and 8 Plus: Press and hold the Power (Sleep / Wake) button on the right side until the Move prompt appears. Then slide it from left to right to turn it off.

To restart iPhone X, XS, XS Max, and XR: Press and hold the Side and Volume Down / Up buttons until you are prompted to move. Then drag the slider to turn off your iPhone.

After turning off your iPhone, just press and hold the side button until you see the Apple logo, then wait a few seconds and your iPhone will restart.

Why Touch ID Stops Working on iPhone iPad?

The reasons why Touch ID doesn’t work are various. Here we conclude as shown below:

Outdated version of iOS. Outdated iOS on iPhone or iPad may cause Touch ID to crash.

Dry or wet finger. Your finger is too dry or wet, causing Touch ID to fail.

Incorrect finger touch on the Home button. Partial finger touch on the Home button is not recognized by Touch ID.

Your original finger is not working. If you have a finger injury and the appearance has changed, Touch ID will not work in a certain way.

As we find out why Touch ID stops working, we can fix this issue by following the solutions in the next part.

How to set up Touch ID correctly?

Setting up Touch ID is easy and simple. Select Settings General Touch ID and the Touch ID passcode. Then go through the process of registering your fingerprints. There are some tips and tricks to keep in mind when using Touch ID.

Read more:  How to Flash Iphone 6 Through iTunes

How to display touch ID on the screen?

There are several ways to enable AssistiveTouch.

  • Go to Settings Accessibility Touch and check AssistiveTouch.
  • Use “Hey Siri” and say “Turn on AssistiveTouch”.

What to do if your fingerprint doesn’t work on iPhone?

Go to Settings Touch ID & Passcode and make sure Unlock iPhone or iTunes Store & App Store is enabled and that you have registered at least one fingerprint. Try to enroll another fingerprint.

What to do if the fingerprint scanner does not work?

Fingerprint not recognized: recheck your fingers

Check if you have something like this on your fingers. Add a new fingerprint to the system, or use another finger that has already been saved. Already when setting up a new fingerprint, you will notice whether the scanner is working or not.

How to activate Touch ID on iPhone 6?

Keep your finger and Touch ID sensor clean and dry. Go to Settings, Touch ID & Passcode, then enter your Passcode. Tap Add Fingerprint and tap the Touch ID sensor while holding the device as you would normally. Place your finger on the Touch ID sensor, but do not press it.

How to recover Touch ID after replacing a button?

In the event of a breakdown of the button itself or the fingerprint scanner, it cannot be restored. When replaced with a new button, it will not work at all. It’s just that there will be no hole in the display from the absence of a button or a broken button. Replacement can only correct a cosmetic defect.

How to activate Touch ID on iPhone?

activate Touch ID from Settings on iPhone

  • Open your iPhone’s Settings app.
  • Find and open “Touch ID and Passcode”.
  • Enter your password.
  • Disable the iTunes app and restart your iPhone.
  • After rebooting, reopen the Settings app.
  • Turn off iTunes and App Store.

How to quickly disable Touch ID on iPhone

Told how to use the new iOS 11 feature.

In iOS 11, Apple added a new feature that allows users to quickly disable the Touch ID fingerprint scanner. In this manual, we told you why such a function is needed at all, how to set it up and how to use it.

Why Apple Added Disable Touch ID

Apple has once again decided to worry about the safety of its users. The Touch ID quick deactivation feature gives iPhone owners the ability to maximize the protection of their smartphones in the event of a variety of emergencies. By blocking Touch ID, the user will exclude the possibility of an attacker gaining access to the iPhone by placing the owners’ fingers on the scanner. Of course (and fortunately), such situations rarely arise, but Apple decided to foresee the actions of its customers in them too.

Another reason for the introduction of the feature to quickly disable Touch ID on the iPhone in iOS 11 is related to Apple’s desire to protect its users from law enforcement. Over the past year, there have been several cases in which police officers literally forced suspects to provide access to their iPhones by scanning their fingerprints.

The loudest of these cases occurred in February. A resident of Norway, suspected of committing a crime, was ordered to unlock his iPhone via Touch ID. By a court ruling, fingerprint blocking of smartphones was deemed unprotected by the country’s constitution. This implies that, at the request of the police, any iPhone user is required to unlock their Touch ID-protected smartphone.

How to quickly disable Touch ID on iPhone

Note: This feature only works on iPhones running iOS 11 or later.

In order to disable Touch ID on the iPhone, you must quickly press the “Power” button five times in a row. Successful operation will display a screen asking you to turn off the iPhone or make an emergency call. At the same time, the function blocks Touch ID, informing you that a passcode is required to activate the fingerprint scanner. In this case, you can unlock the iPhone only with a password. IOS 11 and previous versions of the operating system set a similar limitation every time the iPhone is restarted.

You do not need to make any special settings to enable the function. over, these very settings are not presented in iOS. In the “Settings” → “Emergency SOS” menu, users can only activate the option to automatically call the emergency number by pressing the “Power” button five times and set up emergency contacts. Recent contacts will receive notification messages in case you called emergency services.

How to disable Touch ID on iPhone?

In order to disable Touch ID on the iPhone, you must quickly press the “Power” button five times in a row. Successful execution of the operation will display a screen with a proposal to turn off the iPhone or make an emergency call.

How to unlock iPhone if the button doesn’t work?

How to unlock iPhone or iPad with one tap without pressing the Home button (for iOS 10. iOS 12)

  • Open the “Settings” application;
  • Go to the section “General” → “Accessibility” → “Home”;
  • Activate the “Swipe to open” option.

What to do if Touch ID fails?

If that doesn’t work, recalibrate the Touch ID:

iPhone 6 / 6 plus. How to activate and deactivate Touch ID.

  • go to the menu “Settings. Touch. password”
  • enter a password to unlock your Apple device.
  • reset your phone’s fingerprints
  • rescan the fingerprint to replace them

How to set up Touch ID on iPhone 6?

Go to Settings, Touch ID & Passcode, then enter your Passcode. Tap Add Fingerprint and tap the Touch ID sensor while holding the device as you would normally.

Why iPhone fingerprint doesn’t work well?

What are the main reasons for these problems

the appearance of cuts, abrasions and other marks affecting the fingerprint failure of the Touch ID system settings. failure of the iPhone loop button. other mechanical damage to the smartphone, due to which it is impossible to enter the password

What to do if your fingerprint doesn’t work?

  • Delete the fingerprint that was entered earlier;
  • Go to “Settings”. “Sound” and turn off the sound of unlocking the screen there;
  • Return to “Settings”. “Lock screen and password” and set the sleep time for the screen to 2 minutes;

How to activate Touch ID on iPhone?

activate Touch ID from Settings on iPhone

  • Open your iPhone’s Settings app.
  • Find and open “Touch ID and Passcode”.
  • Enter your password.
  • Disable the iTunes app and restart your iPhone.
  • After rebooting, reopen the Settings app.
  • Turn off iTunes and App Store.

How to set up a Touch ID-enabled iPad or iPhone like new

  • Sign in with your existing iCloud Apple ID. just enter your username (usually your email address) and password).
  • Tap Use different Apple IDs for iCloud and iTunes if that’s how it works.
  • Create a new, free Apple ID.
  • Faucet Skip this step if you don’t want to do this right now or you don’t have an Apple ID yet. You can always go back and create one or log in from the Settings app at any time.
  • Confirm your consent again.
  • Set up Apple Pay, Apple Touch ID payment method, if available in your area.
  • Set up iCloud Keychain if you want to store and sync your passwords across all your devices
  • Customize Siri, Apple’s Voice Assistant. If you need more help, here’s how to set up Hey Siri on iPhone and iPad.
  • Also set up “Hey Siri” if you want Siri to automatically launch with the above phrase.

    Enable Display Scale if you need additional visual accessibility of a larger interface.

    This concludes the initial setup process for iPad and iPhone with Touch ID!

    How to set up Touch ID on iPad or iPhone

    Whether you set up like new, restore from a backup, or switch from a different device, it all starts the same.

    • Touch the slide to customize and, as they say, slide your finger across the screen to get started.
    • Choose your language. If you bought an iPhone or iPad in your country, they should select the one you want automatically.
    • Choose your Country or Region. Likewise, the default should be the correct location if you live where you bought it.
    • Select Wi-Fi Network and enter its password if required. If you don’t have Wi-Fi access or no network found, you can select Use cellular instead for iPhone or iPad with data.
    • Wait for activation on your iPhone or iPad. This may take some time.
    • Choose if you want to enable Location Services. You can always change your mind later, but keep in mind that you need to enable at least some location services to use apps like Maps.
    • Set up your Password and Touch ID. You can skip this step by choosing Set up Touch ID later, but security is important. If you need more help, here’s how to set up Touch ID on your new iPhone or iPad.

    How to set up Touch ID and a new iPhone or iPad

    Having Touch ID on a new Apple device is rare these days. However, there are still a few new products with this feature, including the 2020 iPhone SE and the newest iPad Air 4. If you’ve just purchased any of these new devices, here’s everything you need to know about how to set up Touch ID.

    Understanding your options

    There are several ways to get started with a new iPad or iPhone using Touch ID.

    • Set as “new”, which means starting everything. every setting. from scratch. This is for people who have never used smartphones or online services before.
    • Restore from a previous backup of iPhone, iPad, or iPod touch. You can do this online with iCloud or over USB with iTunes. This is for people who have had a previous iOS device and are moving to a new one.
    • Import from Android, BlackBerry or Windows Phone. Apple has an app on Google Play to make Android easier, but online services allow you to transfer large amounts of data from any old device. This is for people switching to iPhone or iPad.

    How to recover or transfer data from an old smartphone or tablet

    As part of this process, you are given the option to set up your iPhone or iPad as a new device, restore from an iCloud or iTunes backup of your previous device, or. for iPhone. transfer data from Android.

    If you want to recover or transfer data from your old iPhone, iPad, Android device, Windows Phone, Surface or BlackBerry, you have the following options:

    Otherwise, you will need to start like a new one. It is also possible to set up your device as a new iPhone, rather than restore from a backup, as detailed in the article below.

    Questions about how to set up Touch ID on a new iPhone or iPad?

    If you have any problems setting up Touch ID on your new iPhone or iPad, or have other questions about the initial setup process, let us know in the Комментарии и мнения владельцев.

    Read more:  iPhone 7 dfu mode how to enter

    Updated November 2020: Updated for iOS 14 and iPadOS 14.

    How to set up Touch ID on iPhone 6?

    Go to Settings, Touch ID & Passcode, then enter your Passcode. Tap Add Fingerprint and tap the Touch ID sensor while holding the device as you would normally. Place your finger on the Touch ID sensor, but do not press it.

    How to make the touch ID work?

    If that doesn’t work, recalibrate Touch ID:

    • go to the menu “Settings. Touch. password”
    • enter a password to unlock your Apple device.
    • reset your phone’s fingerprints
    • rescan the fingerprint to replace them

    How to set up Touch ID on iPhone 11?

    Go to Settings, Touch ID & Passcode, then enter your Passcode. Tap Add Fingerprint and tap the Touch ID sensor while holding the device as you would normally. Place your finger on the Touch ID sensor, but do not press it.

    How to set up Touch ID on your iPhone or iPad — Apple Support

    Where is the fingerprint on iPhone 12?

    The power button with a built-in Touch ID fingerprint scanner is located on the right side of the smartphone. This arrangement has long been used by many smartphone manufacturers.

    How to activate Touch ID on iPhone 6?

    activate Touch ID from Settings on iPhone

    • Open your iPhone’s Settings app.
    • Find and open “Touch ID and Passcode”.
    • Enter your password.
    • Disable the iTunes app and restart your iPhone.
    • After rebooting, reopen the Settings app.
    • Turn off iTunes and App Store.

    How to put a password on applications on iPhone?

    How to set a password for an app group in iOS 12

    • Go to Settings. Screen Time and select Enable Screen Time.
    • Below we click Use a password code and set a four-digit code, it will be used to lock applications.
    • Go to Settings. Screen Time. Program Limits.

    How to set up Touch ID on iPhone 12?

    To use Touch ID, you must also set a passcode on your iPhone. You can add multiple fingerprints (for example, your thumb and forefinger).

    • Open Settings Touch ID & Passcode.
    • Tap “Add Fingerprint”.
    • Follow the instructions on the screen.

    How to enable, disable, and set up Touch ID on iPhone

    Before activating Touch ID, it is recommended to restart the device, close all applications and wash your hands, since the first time you turn it on, you will need to add fingerprints, and if they are indistinct, then in the future there may be problems with unlocking the device.

    What to do if a feature stops working or crashes

    Some users experience problems immediately after enabling Touch ID, and some after a few days or months. The problem may be as follows: Touch ID does not work, stops working, does not work the first time, does not work correctly. To get rid of all of the above problems, you need to do the following:

      Restart the device by simultaneously holding down the “Lock” and “Home” buttons for 8-10 seconds.

    What is Touch ID

    Touch ID is a password that can be set to unlock the device or to access some applications. Unlike previously existing passwords, which were a combination of numbers or a key sign, Touch ID verifies the fingerprints of the person trying to unlock the phone or tablet and compares them to the fingerprints stored in the device’s memory. If they match, then the unlocking is successful, but if Touch ID suspects that the device is being hacked, it will go into lock mode. The user has three attempts to prove their identity using unique fingerprints.

    The advantage of this technology is that it is the most reliable way to block access to your device or individual programs. If the phone or tablet is stolen, then it will be very difficult for an attacker to get him out of the blocking state.

    Touch ID first appeared on the iPhone 5S and is present on all subsequent phone models. This technology is also available on iPad Air 2 and iPad mini 3.

    How to enable and set up Touch ID on iPhone

    Apple provides users of its technology with a large number of functions designed to ensure complete security and protect the device from penetration of unwanted persons. One such add-on is Touch ID.

    What to Do When Fingerprint Reader Doesn’t Work Well. video

    If fingerprint recovery did not help fix the problems with Touch ID, you need to take the device to a service in order to get advice from a qualified specialist and, possibly, send the device for repair, since the reason is most likely in the stuffing of the phone or tablet. If you have jailbroken your device’s firmware using Jailbreak, then this may be the reason. Also, the reason may be in the iOS version, you need to install the latest firmware on your device for Touch ID to work correctly.

    What you can use Touch ID for?

    At the moment, Apple is very sparingly using the Touch ID technology. With your fingerprint, you can only be content with unlocking your iPhone and purchasing from the iTunes Store, App Store and iBooks Store without entering a password.

    But jailbreak users can afford much more, for example, installing fingerprint protection to open certain folders or applications.

    How to set up Touch ID

    Following a large and detailed article on Touch ID as a technology, one cannot help but raise the issue of setting up the fingerprint scanner on the iPhone and consider possible problems.

    Let me remind you that Touch ID is a great way to use your fingerprint instead of your usual four-digit password. One press of the Home button is enough to unlock your iPhone, let’s see how to set up Touch ID.

    Touch ID does not work

    If you encounter problems when working with Tocuh ID, the reasons can be very different. Apple recommends in such cases any triviality. make sure that you have the latest version of iOS, the “Home” button is not overgrown with dirt, pay attention to whether the entire finger covers the sensor and stuff like that

    If all of the above is not the case in your case, then you can recommend trying to register another fingerprint.

    Problem still exists? Your case is the worst. Apparently you are faced with a Touch ID manufacturing defect. Most often, this is accompanied by the error “Failed to scan, please go back and try again“when performing a fingerprint scan and if restarting the iPhone did not help you, then the phone needs to be carried to the service center.

    The most disgusting thing about this problem is that sometimes the seller is to blame. The fact is that in the presence of a marriage, unscrupulous sellers collect one of the two iPhones, and since the Touch ID sensor is connected to the native processor, they cannot find each other in the body of the same phone. This is just one of the possible reasons, you should not assume only her, but such an option is quite possible.

    What to do if Touch ID doesn’t work well

    It is not uncommon for iPhone and iPad users to complain about the poor performance of Touch ID. over, difficulties with fingerprint recognition can arise even with a button cleared of dirt and dust and clean, dry fingers.

    Few people know, but iOS has a built-in function to correct your fingerprint data. In other words, Touch ID recognition accuracy can be improved and it is not difficult at all:

    • We go to: Settings. General. Touch ID and password. Touch ID;
    • register multiple fingerprints, if you have not done so before;
    • now in the main menu of Touch ID settings, simply touch the Home button and you will see how the registered “finger” will be highlighted in gray;
    • repeat this procedure several times, touch the sensor at different angles.

    Thus, you will be able to “train” Touch ID without even having to re-register your fingers.

    If you didn’t find the answer to your question or something didn’t work out for you, and there is no suitable solution in the Комментарии и мнения владельцев below, ask your question through our help form. It’s fast, simple, convenient and doesn’t require registration. You will find answers to your own and other questions in this section.

    How to set up and use Touch ID on your iPhone 6 or 6 Plus

    The Touch ID sensor lets you unlock your device without a password by simply placing your finger on the Home button. It also allows you to approve purchases from the iTune Store, App Store and iBooks Store, and use it in various third-party apps.

    You can set up Touch ID during the initial setup process, however if you decide to set it up later or want to add another fingerprint then we’ve covered this guide.

    How to use Touch ID

    Now lock your iPhone by pressing the Sleep / Wake button and place your newly added finger on the Home button. It should unlock your iPhone. If you want to confirm your iTunes Store, App Store, and iBooks Store purchases with your fingerprint, tap the iTunes & App Store toggle to turn it on. A number of third-party apps, such as 1Password, have also added Touch ID support, so you can secure and unlock them with Touch ID by placing your finger on the Home button.

    How to set up Touch ID on your iPhone 6 or iPhone 6 Plus

    Follow these steps to set up Touch ID or add a new fingerprint to your new iPhone 6 or iPhone 6 Plus.

    • Launch the Settings app, scroll down and tap Touch ID & Password.
    • Enter your password when prompted. If you have not set a password, you will be prompted to set it as you will need it for additional security checks, such as when you restart your iPhone for the first time, add new fingerprints, etc.
    • Tap on Add Fingerprint option.
    • Place the finger you want to add on the Home button. Lift and hold your finger on the Home button several times. You will see the fingerprint animation on the display fills in red as you progress. Move your finger lightly between the scanned images. It takes less than a minute to set up.
    • After the entire fingerprint animation turns red, you will be prompted to adjust the grip to capture the edges of the fingerprint.
    • Place your finger on the Home button again, but this time lift and touch the Home button several times.
    • After the entire fingerprint animation turns red, it will inform you that Touch ID has been successfully set up and that finger can now be used to unlock your iPhone. Click on “Continue”.

    That’s it, your fingerprint has been added. You can follow the same process to add up to 5 fingerprints.

    How to determine which fingerprints you have registered

    If you later want to know which fingerprint you have registered on your device, just touch the Home button with your finger, it will highlight the entry in the list if you have added it.

    Read more:  How to transfer numbers from Android to iPhone

    How to determine which fingerprint you have registered on your iPhone

    How to set up fingerprint on iPhone

    Instructions for setting up the fingerprint scanner on the iPhone. For scanning the fingerprint, the Touch ID sensor module built into the Home button is responsible. It protects your smartphone and replaces the password on the lock screen.

    Not all iPhone models support Touch ID. below is a list of smartphones without a scanner:

    they can also be distinguished by the touch button

    • iPhone
    • iPhone 3g
    • iPhone 3gs
    • iPhone 4
    • iPhone 4s
    • iPhone 5
    • iPhone 5c
    • iPhone X. Touch ID replaced with Face ID (facial recognition)

    Setting up Touch ID

    Go to Settings Touch ID and Passcode Add Fingerprint.

    Just follow the instructions on the screen. the system asks you to put your finger on the scanner several times.

    Upon completion of the scan, you will need to come up with a password code.

    The password will be required in the event of a scanner failure, as well as to change the fingerprint settings, so be sure to remember it, or better. write it down.

    Ready. You can now unlock your smartphone by placing your finger on the Home button.

    How to use Touch ID to shop

    You can use your fingerprint for App Store and iTunes Store purchases. To do this, go to the Touch ID Settings and Passcode and activate the switch opposite the iTunes Store and App Store. When you enable this function, the system will ask you for your Apple ID password. enter it and you’re done.

    Now you can make a purchase with one finger press on the Home button.

    Set up a Touch ID-enabled iPad or iPhone as new

    If this is your first time using an iPhone or iPad and you don’t need to move your data, this is what you need to do. Either way, you need to connect your device to your iCloud account. You have several solutions for this:

    • Sign in with your current iCloud Apple ID. enter your username (usually your email address) and password).
    • tick Use different Apple IDs for iCloud and iTunes if that’s how it works.
    • Make another one, free Apple ID.
    • Click Skip this step if you don’t want to do this at this time or don’t have an Apple ID yet. Typically, you can go back and do one or log in from the App Settings at any time.
    • Create Apple Pay, Apple’s Touch ID based payment option if available out there somewhere.
    • Create iCloud keychain if you need to store and sync passwords across all your gadgets.
    • Start Siri, Apple’s Voice Assistant. In case you need more help, here are the tools you can use to set up Hey Siri on iPhone and iPad.
    • Likewise, set up “Hey Siri” in case you need to automatically launch Siri with the previously mentioned facial expression.
    • Click to send Diagnostic Data to Apple when apps crash or other issues. If you don’t want to do this, just click Don’t Send.

    Likewise, this concludes the initial setup process for iPad and iPhone with Touch ID.!

    Set up Touch ID / Face ID on iPad or iPhone

    Whether you set up as new, restore from a backup, or change from another device, everything happens the same.

    • Complete the customization slide and as they say, swipe across the screen to start.
    • Choose your language. If you purchased your iPhone or iPad in your country, you should choose the correct one.
    • Ship to your country or region. Likewise, by default it should be the right place if you live where you have it.
    • Select a Wi-Fi network and enter its password, if necessary. If you are not suitable for Wi-Fi or the network is not found, you can choose “Use Cellular” instead of the iPhone or iPad with information.
    • Wait for your iPhone or iPad. He may have a few of your seconds. Choose if you want to enable Service Location. You can usually change your mind later, but remember that you will need to enable at least some regional administrations to use apps like Maps.
    • Start your Passcode and touch ID. You can avoid this by choosing touch ID later however security is important. The same procedure is performed with

    Recover / transfer your data from an old smartphone or tablet

    As part of the process, you are presented with a solution to set up your iPhone or iPad as another device, restore from an iCloud or iTunes backup of the previous device. Or for iPhone, you can transfer data from Android.

    If you need to recover or move information from your old iPhone, iPad, Android gadget, Windows Phone, Surface or BlackBerry, here are your alternatives:

    Otherwise, you will need to start a new one. It is also possible to set up your gadget as a new iPhone, rather than restore from a backup, as detailed in the article below.

    Setting screen time and more

    Screen Time lets you know how much time you and your kids are spending on your devices. It also allows you to set limits for the daily use of the app. Once you’ve established Screen Time, you activate True Tone if your device supports it, and use Display Zoom to adjust the size of icons and text on the home screen. If you have an iPhone X or later, learn more about using gestures to navigate your device. If you have an iPhone 7, iPhone 7 Plus, iPhone 8, or iPhone 8 Plus, you can customize the Home button press.

    Setting up Touch ID and your new iPhone or iPad

    Recently, the iPhone Measure of customization has changed dramatically in light of the iPhones themselves. Apple just keeps trying to make it easier. In truth, this is so natural that you only have to do a few things in order to switch from your old iPhone to another. In addition, installing a new iPhone made of plastic without any preparation is not much more difficult. gone hours of physically duplicating passwords just to want to the home screen. However, there are a few more tricks that can help things go according to plan. How about we see an approach to properly set up Touch ID on a new iPhone / iPad.

    Before you start:

    There are a couple of different ways to get started: Another iPad or iPhone using Touch ID.

    • Set as “new”, which means to start all over. each setting. without any preparation. This is for people who have never used a mobile phone or online services before.
    • Recover from a past gain of iPhone, iPad or iPod touch. You can do this online using iCloud, or over USB using iTunes. This applies to people who have had a previous iOS device but are switching to a different one.
    • Import from Android, BlackBerry or Windows Phone. Apple has an app on Google Play to make it easy to create Android, however online services allow large amounts of data to be transferred from an unspecified gadget. This is for people switching to iPhone or iPad.

    What will we see here?

    Setting up another iPhone has become as clear as possible at any time. With a variety of robust strategies, you can safely move all your information, including photos, videos, and music, from one iPhone to another, or from an Android device to an iOS device. In case you recently unpacked another iPhone / iPad and are going to set it up without a hitch. I hope we taught you how to set up Touch ID on iPhone and iPad.

    Touch ID does not work well on the iPhone: how to properly configure the fingerprint sensor in the iPhone

    The Touch ID fingerprint sensor on a fairly fresh iPhone does not always work on touch and you have to constantly be asked to enter the password? If you are faced with a similar problem, then in this article we will tell you how to fix it.

    Everyone knows that after buying a new iPhone, you need to complete the activation procedure and the initial setup of the device, which includes setting up the Touch ID fingerprint sensor built into the Home button. The user is asked to add a fingerprint with which the iPhone can be unlocked.

    From our many years of observing users setting up a new iPhone, we can confidently say that adding a fingerprint to Touch ID during initial device setup is often very quick and not always with an understanding of the process. Most users hold their iPhone quite differently while adjusting the biometric sensor than during normal use. This is the whole secret.

    In addition, after the initial setup of the iPhone, few people return to the Touch ID options (in the iOS settings) to continue the process of improving the sensor. As a result, users continue to use the only fingerprint that was recorded in Touch ID when the iPhone was first set up. But in the parameters of the sensor, you can add as many as 5 prints. So…

    Touch ID works poorly on iPhone: how to properly configure the fingerprint sensor in iPhone or iPad

    Open the Settings app on your iPhone or iPad and go to Touch ID & Passcode.

    Delete all added fingerprints. To do this, select each fingerprint and click Delete fingerprint.

    Hold your iPhone or iPad the way you would normally hold the device before unlocking.

    Follow the procedure for adding all five prints as follows:

    • add the thumbprint of the right hand twice;
    • add the thumbprint of the left hand twice;
    • add the print of the index finger of the right hand (if you are right-handed) or of the left hand (if you are left-handed) once.

    The point of this operation is to add more fingerprints to the most used unlocking option.

    The scheme proposed by us, if desired, can be changed. For example, if you always unlock the device with one hand, then it will not be superfluous to add 3, 4 or even all 5 possible fingerprints to the Thumb.

    Try it now. In the vast majority of cases, this will solve the problem of poor performance of Touch ID.

    In case the sensor still does not respond well after completing the fingerprint adding procedure, try restarting the device. If the reboot did not help, then two options remain. either you are the owner of hands with an abnormal fingerprint structure (we have met such users) or the problem is still in the Touch ID sensor itself.