How to set up cable on your TV

Table of Contents

Sony setup

The setup for cable TV on Sony TVs is slightly different from other models where the steps are almost identical. Also, on older Sony Bravia models, you need to select the country Germany in the settings.

  • Press the HOME button and find the Settings menu item.
  • Next, we are looking for a Digital configuration.
  • Open the item Automatic tuning of digital stations.
  • Select the type of connection TV Cable or DVB-C.
  • If a list of operators appears, choose our own, if you don’t find the one you need, click on Others.
  • Specify the scan type Full, if you know the frequency of your operator, you can specify the Network.
  • Click start and wait for the full channel setup.

Setting up satellite channels

Users who have installed a satellite dish will probably also have difficulty finding channels. Immediately, we note that the process of tuning digital channels and satellites is significantly different.

cable, your

So, the satellite dish is directed in the right direction, which means it’s time to find and tune the channels on the TV. Immediately, we note that satellite TV is not only a dish, but also a receiver connected to an antenna cable. As a result, the TV operates in the mode of the most ordinary monitor.

Few people know, but under the influence of natural conditions (heavy wind, heavy rain, snow) satellite dishes can change the originally installed position, as a result of which a failure will occur. Constantly check and correct the position of the antenna, otherwise a stable signal will disappear, and it will be very difficult to return previously saved channels.

The tuner is controlled using a special remote control. Take it and click on the “Menu” button, follow the step-by-step instructions that come with the equipment. There are a lot of TV channels, so save only those that you plan to watch at least sometimes.

Practice shows that the most viewed channels are of a cognitive nature, that is, they tell about travel, the mysteries of the planet. Sports TV channels are also popular. Therefore, it is not necessary to connect additional channels, save only those that you plan to watch.

LG setup

In order to install cable channels on an old-model alji TV, you must definitely change the country, because when you select Russia, the DVB-C format will not be available and to enable it, you must put Finland or Germany in the TV parameters. Then you will be able to tune digital channels.

  • Go to the menu, click on auto search by selecting Cable TV.
  • You will be given a list of operators, choose your own, if yours is not there, be sure to click on Others.
  • Selecting Full Search
  • We put a tick on digital channels.
  • Click on ok and wait for the end of the search.

How to set up cable TV on Smart TV

After you have connected to a cable network, you need to set up your TV to receive cable TV. Typically, the cable operator sets up your TV when connected. But sometimes this service is paid and you do not want to overpay, or in the future, a failure may occur and all channels will simply disappear and you will need to reconfigure the cable channels yourself.

Almost all cable providers provide digital television services, and many operators have also retained the analog broadcasting format, which means that subscribers do not need to purchase digital set-top boxes.

Cable operators mainly provide digital channels in the DVB-C format, so make sure your TV supports this format before setting up. This format is also present on older models of LCD TVs that do not support DVB-T2, so check your TV manual

Cable TV setup

As practice shows, providers independently configure channels for their customers. However, sometimes malfunctions occur, for example, the TV did not shut down correctly due to power drops. as a result, the saved parameters are erased.

Therefore, each user should be able to correctly install digital channels so as not to constantly call specialists and not spend money on it.

How do I tune channels on my TV? If circumstances forced you to set up the broadcast yourself, be sure to follow the simple step-by-step instructions:

  • Immediately after turning on the TV-device, the notification “digital TV channels are not tuned in” will appear on the screen.
  • Take the remote control, go to the main menu by clicking on the corresponding button.
  • Go to the “Tune TV channels” section, then select the “Automatic tuning” command and click “OK” or “Start”.
  • The TV will start scanning the incoming signal, identifying available TV channels. Automatic tuning is bad because doubles appear because of it, and besides, the broadcast quality leaves much to be desired: stripes, interference, ripples. It is possible that the sound will be distorted. It is better to remove such channels immediately.
  • Automatic search lasts only 2-3 minutes, it all depends on the number of available channels. When scanning is complete, a list of saved TV channels will appear on the screen.
  • An alternative is manual tuning, but it is time consuming as the user enters the frequency. As a result, you can spend more than 30 minutes on channel tuning.

The described algorithm for setting up cable television is generally accepted; certain subtleties may arise in accordance with the equipment used. The characteristic features are described in detail in the instruction manual for the television equipment.

What if there is no remote control? The setting can also be carried out using the buttons located on the device panel. If you are using Smart TV, then you can connect a computer mouse or keyboard.

Setting up your Samsung TV

Set up Samsung to receive cable TV in a snap.

  • Enter the TV settings by pressing the Home or MENU button.
  • Go to submenu Broadcast or Channel.
  • In the Antenna section, put the Cable.
  • Click on Autotuning.
  • Then you need to select the type of channels Digital and Analog
  • The search mode must be selected Full. If you know the parameters of your network, then you can select Network or Fast, but for these two modes you need to enter your network data in the cable search parameters.
  • Click on Search and wait for the end of the process.

Setting up your Samsung TV

Set up Samsung to receive cable TV in a snap.

  • Enter the TV settings by pressing the Home or MENU button.
  • Go to submenu Broadcast or Channel.
  • In the Antenna section, put the Cable.
  • Click on Autotuning.
  • Then you need to select the type of channels Digital and Analog
  • The search mode must be selected Full. If you know the parameters of your network, then you can select Network or Fast, but for these two modes you need to enter your network data in the cable search parameters.
  • Click on Search and wait for the end of the process.
Read more:  When You Turn On Your Computer Black Screen What To Do

Is it possible to connect a TV without Smart TV to the Internet?

The Internet can only be connected to a TV with Smart TV.

How To Connect Cable To A TV-Step By Step Tutorial

If you have a TV without Smart TV, then the Internet is not needed at all. Since there are no applications with which you can watch videos, open websites, etc. There are TV models without Smart TV, but with LAN input.

How to connect a digital set-top box to an old Funai TV?

The connection diagram through the “tulip” is as follows:

  • Turn off the TV and receiver from the sockets.
  • Plug the connectors on the cables into the jacks where they fit.
  • Connect the antenna cable to the set-top box.
  • Turn on the TV, go to the menu and select the AV mode.
  • Tune channels on a digital set-top box.

Is it possible to connect a digital set-top box to cable TV?

DVB-T / T2 set-top boxes are not designed to receive digital cable TV. Modern TVs do not need a set-top box to receive a signal! Be sure to check for a built-in DVB-C tuner in your TV. NO EXTENSION REQUIRED TO WATCH ANALOGUE TV CHANNELS!

How to tune digital channels on an old LG TV?

Setting up digital TV on LG TVs

  • Press the MENU button on the remote control to start setting.
  • In the window that appears on the TV, select the SETUP tab, press the OK button.
  • In the menu that appears, select the OPTIONS tab and press OK.
  • Select the country RUSSIA and click OK.
  • Then go to AUTO SEARCH tab and click OK.

Is it possible to connect an old TV to the Internet?

If you have a very old TV with only tulip connectors on the body without Internet and WI-FI support, then it can also be connected to a wireless network. To do this, you need to purchase a separate TV set-top box for Android.

Is it possible to watch digital channels on an old TV?

Tune TV to the channel of the VCR, and you will be able to watch the channels even if the old TV does not have the corresponding input (AV). It is quite possible to watch digital TV on a regular TV, but for this you need to connect and configure a digital set-top box.

How to install HD VideoBox on TV?

The application is downloaded and installed in the standard way for Android devices:

  • Open the menu of your TV and select “Browser” in it.
  • Click on the link in the description “Install HD VideoBox”;
  • On the next page there are two sources for downloading, select one of the proposed markets and use it to download the file.

How to connect PlayStation 4 to Xiaomi TV?

It is enough to follow the step-by-step instructions:

  • Connect the HDMI cable to the TV to the appropriate connector on the side or rear panel.
  • Insert the second plug of the cable into the HDMI connector of the Sony Playstation.
  • Plug in the power cord, and connect the other end to the set-top box connector.

How to scan channels on Hisense TV?

In order to tune digital channels on hisense Smart TV, you need a remote control and some of your time.

  • Press the Menu button and look for the System section, it is in it that the settings we need are located.
  • Find the Settings item and click OK.
  • Next, click on the Channel item.
  • Choosing Autosearch.

How to install apps on Hisense TV?

For those who are not interested in how I got to this. just the instruction:

  • Go to Smart TV and open TV Browser.
  • We drive in the address hisense.alexxnb.ru.
  • We see a small list of applications. click on the Install buttons to put the desired one.
  • Everything.

How to tune your TV to cable TV?

Set up Samsung to receive cable TV in a snap.

  • Enter the TV settings by pressing the Home or MENU button.
  • Go to submenu Broadcast or Channel.
  • In the Antenna section, put the Cable.
  • Click on Autotuning.
  • Then you need to select the type of channels Digital and Analog
  • Search mode must be selected Full.

How to connect Wi-Fi to a Xiaomi TV?

how to connect Xiaomi Mi TV to Wi-Fi

  • turn on Xiaomi Mi TV;
  • go to “Settings”, go to network settings and then to the Wi-Fi settings section;
  • select our own in the list of available WI-FI networks;
  • enter the password and click OK.

How to set up cable TV on a Xiaomi TV?

How to retune your TV to digital if you have cable TV?

  • Enter the menu using a special button on the remote control.
  • Go to the “Channel” section, which usually has a satellite dish icon.
  • Select “Autosearch”.
  • From the proposed connection options, select “Cable”.
  • Then select “Digital” and click on “Start”.

How to tune your Samsung TV to Cable TV?

Setting up digital channels on Samsung TVs

  • Enter the main menu by pressing the [Menu] button on the remote control.
  • The TV may ask for a PIN.
  • The following country settings should be set:
  • Next, in the “Channel” section, select “Cable search parameters”
  • Enter Cable search parameters:…
  • Return to the “Channel” section of the main menu and select “Auto tuning”

How to tune channels on your TV?

  • Turn on the menu using the “Home” button on the remote.
  • Go to the TV settings, then to the “Broadcast” section.
  • Select signal source “Antenna”.
  • Specify the type of channels you want to search (by default. “Digital”).
  • The menu will prompt you to select an operator and a search mode.

How to enable HDMI on Mi TV?

Press the central button on the remote control, select “System settings” and then “Additional. Device settings. Inputs”. HDMI EDID is now active, enable it.

How to set up cable TV on your Toshiba TV?

TOSHIBA Equipment Setting Instructions

  • In the menu item Ant./Cable In, select the Cable.
  • Go to DTV manual tuning tab and press OK.
  • Enter frequency, modulation, symbol rate. Also available in the Auto. Setting set parameters:…
  • After pressing the OK button, the search will start, as a result of which the channels should be found.

How to tune your TV to cable TV?

Set up Samsung to receive cable TV in a snap.

  • Enter the TV settings by pressing the Home or MENU button.
  • Go to submenu Broadcast or Channel.
  • In the Antenna section, put the Cable.
  • Click on Autotuning.
  • Then you need to select the type of channels Digital and Analog
  • Search mode must be selected Full.

How to install apps on a Xiaomi TV?

How to install additional programs on a Xiaomi TV?

  • Via the Mi TV Assistant application (Russified version is recommended).
  • You should download the required APK files to your computer, transfer them to a USB flash drive and upload them to TV from it;
  • The third option is a combination of the two previous.

How to connect a monitor to cable TV?

Make sure your cable (TV) supports DVI or HDMI connectors. You also need speakers or a stereo system that is capable of receiving a digital signal (there is an RCA cable). If the monitor does not have an HDMI connector, then you still have to find an adapter from DVI to HDMI. The monitor must have either DVI or HDMI output.

How to start your computer in Windows 10 Safe Mode?

We go into safe mode using the Start menu or the lock screen. Depending on the computer, when you start it, you must press the key combination [Shift] and [F8] or, for example [Esc], [del], [F1], [F2], [ F8], or [F10].

What to do if a black screen after updating Windows?

Users facing a black screen after installing the update can press CtrlAltDelete and force a reboot, after which the system should boot normally. You do not need to run System Restore, the described method should bring the OS back to life.

What to do if after restarting the computer black screen?

One of the easiest ways to fix the black screen problem is to reboot the OS and disable Fast Startup Restart and Disable Fast Startup

  • Press Backspace several times.
  • Enter your password to log into your account (if any).
  • Press Enter.

How to enter Windows 10 Safe Mode if there is a black screen?

To boot Windows in Safe Mode:

  • Press the Win R keyboard shortcut (Win is the Windows logo key) to bring up the Run window.
  • Enter msconfig in the box and click OK.
  • Open the Boot tab and in the Boot Options section, check the box next to Safe Mode.

How to set up cable TV on a Xiaomi TV?

Setting up digital channels on a Xiaomi TV (Mi TV)

  • Then select the item Search for channels Select the item Cable
  • Under Tuner Mode, also select Cable
  • Set the broadcast type to Digital
  • Then click on the Start item Wait for the search to end

What to do if the prefix writes no signal?

When there is no signal on the digital set-top box or TV, try returning the settings to the factory defaults. In rare cases it helps. Then you again need to scan the broadcast for the presence of channels. The cause of the problem may be a floating failure due to faulty logic chips.

Read more:  How to Turn on the Screen on a Computer

Why is there no signal on the monitor?

The most common reason why there is no signal on the monitor or it is transmitted with interference is a missing or poor connection to the system unit. First of all, be sure to check if the cable from the monitor is securely attached to the input of the computer’s video card.

What to do if your computer does not start after updating Windows 10?

When Windows 10 does not boot after the upgrade, you can run Startup Repair, for this you need a Windows 10 installation disc. Plug in the Windows 10 installation disc or bootable USB drive and start your computer. Next select Windows 10 and restart your computer.

Is it possible to connect a digital set-top box to cable TV?

DVB-T / T2 set-top boxes are not designed to receive digital cable TV. Modern TVs do not need a set-top box to receive a signal! Be sure to check for a built-in DVB-C tuner in your TV. NO EXTENSION REQUIRED TO WATCH ANALOGUE TV CHANNELS!

How to set up cable TV on DEXP TV?

  • Press the MENU key on the remote control. Select the “Channels” section
  • Next, in the Autosearch item, select “Cable”
  • Go to the DTV line and press “ENTER”
  • Specify the search type Full search and click Start
  • After completing the search, you will find Digital and Analogue channels.
  • Configuration complete.

How to connect your TV to cable TV?

Set up Samsung to receive cable TV in a snap.

  • Enter the TV settings by pressing the Home or MENU button.
  • Go to submenu Broadcast or Channel.
  • In the Antenna section, put the Cable.
  • Click on Autotuning.
  • Then you need to select the type of channels Digital and Analog
  • Search mode must be selected Full.

What to do if the TV shows that the channels are not tuned?

How to tune a digital if you are watching TV through an antenna?

  • Disconnect the power to the TV.
  • Connect the antenna cable to the antenna input of the digital TV.
  • Plug in the power and turn on the TV.
  • Go to the appropriate section of the TV settings menu and activate the digital tuner.

How to set up cable TV on a JVC TV?

In order to independently set up digital television on your JVC TV, connect the TV cable coming from the antenna to the TV jack.

  • Take the remote and press the MENU button.
  • Press the right button to go to the Channel section.
  • Next, you need to select the Type of tuner Cable or Antenna.

How to connect the remote to a Xiaomi TV?

Pairing In the main menu of the TV, enter the Mi TV of the device External device and Bluetooth Mi Bluetooth remote Add Mi remote control, follow the TV manual. After successful pairing, a notification about successful pairing of devices will appear on the TV.

How to tune cable channels on your LG TV?

Tuning and sorting channels on LG TVs

How to Connect a TV to a Cable Box

  • Press the SETTINGS button on the remote control to start setting.
  • In the window that appears on the TV, select the CHANNELS tab, press the OK button.
  • The Autosearch menu will appear on the screen, in which we select the CABLE TV item, press the OK button.
  • Operator selection point.

How to tune your TV to cable TV?

Set up Samsung to receive cable TV in a snap.

  • Enter the TV settings by pressing the Home or MENU button.
  • Go to submenu Broadcast or Channel.
  • In the Antenna section, put the Cable.
  • Click on Autotuning.
  • Then you need to select the type of channels Digital and Analog
  • Search mode must be selected Full.

How to connect the Internet to a Xiaomi TV?

how to connect Xiaomi Mi TV to Wi-Fi

  • turn on Xiaomi Mi TV;
  • go to “Settings”, go to network settings and then to the Wi-Fi settings section;
  • select our own in the list of available WI-FI networks;
  • enter the password and click OK.

Why is there no signal on the TV screen?

The problem may lie in the connecting cables (starting from the disconnected connector and ending with its failure), in the ports of the TV, the satellite dish, the antenna of the satellite converter. The second common reason why the TV says “no signal” is problems with the satellite dish.

How to tune the antenna on a Haier TV?

What Smart TV Owners Need to Know from Haer

  • Connect the antenna to the corresponding antenna connector of the Smart TV.
  • Plug the TV into the power supply.
  • Using the remote control, press the “MUNI” button and open “Channel” in the menu, then “OK”.
  • Select DVB “Antenna” or “Cable“.

How to tune channels on a TV high?

Setting up digital channels on Haier TVs (for example, LE32K6000S model)

  • click “OK”:
  • Enter the TV menu
  • In the TV menu in the “CHANNEL” section, select “Auto tuning”, confirm “OK”
  • Set the automatic channel search parameters as follows

How to turn on a movie from a USB flash drive on a Haier TV?

  • find a USB port on the TV receiver panel;
  • insert a flash drive into it;
  • if switching did not happen automatically, then switch the TV to AV mode;
  • select a file from the list on the drive and enable viewing.

How to connect a monitor to cable TV?

Make sure your cable (TV) supports DVI or HDMI connectors. You also need speakers or a stereo system that is capable of receiving a digital signal (there is an RCA cable). If the monitor does not have an HDMI connector, then you still have to find an adapter from DVI to HDMI. The monitor must have either DVI or HDMI output.

LG setup

In order to install cable channels on an old-model alji TV, you must definitely change the country, because when you select Russia, the DVB-C format will not be available and to enable it, you must put Finland or Germany in the TV parameters. Then you will be able to tune digital channels.

  • Go to the menu, click on auto search by selecting Cable TV.
  • You will be given a list of operators, choose your own, if yours is not there, be sure to click on Others.
  • Selecting Full Search
  • We put a tick on digital channels.
  • Click on ok and wait for the end of the search.

Sony setup

The setup for cable TV on Sony TVs is slightly different from other models where the steps are almost identical. Also, on older Sony Bravia models, you need to select the country Germany in the settings.

  • Press the HOME button and find the Settings menu item.
  • Next, we are looking for a Digital configuration.
  • Open the item Automatic tuning of digital stations.
  • Select the type of connection TV Cable or DVB-C.
  • If a list of operators appears, choose our own, if you don’t find the one you need, click on Others.
  • Specify the scan type Full, if you know the frequency of your operator, you can specify the Network.
  • Click start and wait for the full channel setup.

Setting up TVs Doffler, Polar, DEXP, Leben.

The interface of these TVs is sometimes the same since they use the same software. To set up cable television on these TVs, you must enable DTV mode in advance by clicking on Source.

  • In the menu, use the down button to select the Channel item
  • Here you will need to do a few steps by selecting your country and Current input Cable.
  • Click on autosearch.
  • We select All channels you can choose which channels you need.
  • Search type Full and click on Start.

In some models, the menu may differ, but the basic actions are almost the same.

Setting up your Samsung TV

Set up Samsung to receive cable TV in a snap.

  • Enter the TV settings by pressing the Home or MENU button.
  • Go to submenu Broadcast or Channel.
  • In the Antenna section, put the Cable.
  • Click on Autotuning.
  • Then you need to select the type of channels Digital and Analog
  • The search mode must be selected Full. If you know the parameters of your network, then you can select Network or Fast, but for these two modes you need to enter your network data in the cable search parameters.
  • Click on Search and wait for the end of the process.

Cable TV setup

When searching for cable channels, you will need to select which channels you want to watch digital or analog, you can also select both lists in the settings.

  • Press the MENU button on your remote control.
  • Find the CHANNELS menu section.
  • Next, you need to enable Autosearch for channels.
  • Country selection, Germany or Finland is recommended for old TV models, in newer ones choose Russia.
  • Antenna Selection. choose Cable, Cable TV or DVBC.
  • DTV channels are digital only, ATV are analog.
  • Search mode Full and start the search.
  • We are waiting for the end of the installation of channels.

How to set up cable TV

After you have connected to a cable network, you need to set up your TV to receive cable TV. Typically, the cable operator sets up your TV when connected. But sometimes this service is paid and you do not want to overpay, or in the future, a failure may occur and all channels will simply disappear and you will need to reconfigure the cable channels yourself.

Read more:  How To Find An Asset Phone Number

Almost all cable providers provide digital television services, and many operators have also retained the analog broadcasting format, which means that subscribers do not need to purchase digital set-top boxes.

Cable operators mainly provide digital channels in the DVB-C format, so make sure your TV supports this format before setting up. This format is also present on older models of LCD TVs that do not support DVB-T2, so check your TV manual

Which Search Type to Choose Full, Network, Fast.

Many people, when setting up their TV to receive cable channels, make mistakes by choosing the wrong type of channels. For example, when choosing Network, you will need to enter the start and end frequency, QAM modulation, and stream rate. These parameters are different for each operator, so don’t bring anything here if you don’t know for sure. Therefore, by choosing Full search, the TV will tune all the available channels by itself, only a little longer.

Setting up a digital cable box.

Cable operators use a variety of digital set-top boxes. It is not difficult to set it up, sometimes it is easier to do it than on a TV.

  • After you have connected the set-top box to the TV with the appropriate cable, enter the set-top box menu.
  • If you have a universal set-top box like the World Vision T62A that receives air and cable, you need to select the DVB-C search range.
  • Turn on Autosearch, broadcast mode Full.
  • We are waiting for when all channels are scanned, it may take some time.

Connection and setup procedure

Cable TV is widespread today because the signal comes from an outlet on the wall, not an antenna. And the signal to this output is supplied by the selected television operator-provider.

How to connect a TV with an old plug

Before F-plugs appeared, other designs were used, however, they did not require soldering. Mounting Soviet connectors, the subscriber’s soldering iron was the best friend.

To connect, you need the cable described in the article and a plastic plug (old model). A knife, pliers or nippers will come in handy from tools.

  • First, disassemble the plug. Turning counterclockwise to separate the body and the metal head.
  • The body is put on the cable.
  • Remove 1 cm of plastic sheath.
  • Trim about 5 mm of shielding foil.
  • Insert the plug into the cable (the shield and the central core must not touch).
  • Pliers squeeze the foil (without effort, the main thing is to ensure contact between the surfaces).
  • Tighten the screw that secures the copper strand.
  • Connect the body to the metal part.
  • Connect to TV.

Cable TV connection. detailed instructions

Analog TV broadcasting in Russia is gradually being replaced by digital, which opens up access to more channels, and in high quality. Despite the rapid development of technology, many people now prefer to relax on the couch after a hard day, watching their favorite TV show. How to connect cable TV to a TV, what are the features of this broadcast and what you need for this. about this in the article.

Cable TV is a method of broadcasting in which signals are transmitted over a wired route.

Manual setting

This method allows you to tune TV channels manually. To do this, go to the menu and select “Manual setting”. In the window that appears, enter the broadcast and frequency data. Then confirm the actions by clicking on “OK”. To continue the search, each time you have to press “Next” or the arrow to the right.

The signal with manual tuning is better, but the method takes more time. After successful completion, the subscriber will open 20 free TV channels.

Features of cable TV

The advantage of digital cable broadcasting is high picture quality (HD content) and clear sound. The system works as follows: the provider. the service provider, transmits the encoded signal to the TV, which is decrypted by the set-top box connected to it, and a high-quality picture is displayed on the screen. The principle of operation is similar to how a computer “communicates” with the Internet.

Compression technology enables the manufacturer to send more TV channels to the subscriber. But this is not the main advantage. With the advent of digital television, the functionality of televisions has expanded. Now the viewer can pause the broadcast at any time or record it and save it on the hard drive to watch later.

  • detailed picture on the screen, without ripples, interference and distortion;
  • the signal quality remains stable, regardless of the distance of the antenna;
  • both Russian and foreign TV channels are available;
  • access to interactive applications, games, various utilities;
  • if desired, you can connect HDMI channels, but provided that the equipment is capable of reproducing content of such resolution.

Cable TV provides access to interactive applications and games.

Connecting to cable television is a service that requires a monthly subscription fee. The amount depends on the selected telecom operator.

Antenna and tuner connection

Almost any antenna is capable of receiving a signal. Even the one that was used to watch analogue broadcasts (including the well-known “Polish” one) will do. True, here they take into account the terrain and how far from the house the tower is. If it is nearby, literally in the same city, the antenna may not be needed at all. If the tower is far away, the antenna must be with an amplifier. And this does not always improve the quality of the signal, in some cases it has to be lifted to the mast.

In apartment buildings, the antenna is tuned by specialists, directing it strictly to the tower. There is a lot of information on the network about where the signal transmitters are located, which will not be superfluous with manual installation.

If the TV is old, it probably does not have a receiver that decrypts the signal, then you will have to buy a set-top box separately. This is a compact device that can be connected to a TV. An antenna is connected to it.

There are many digital set-top boxes on the market, there are even sets that include an antenna. The difference between them is in price and functionality. Features of consoles:

  • many models have a USB port, into which you can always insert a USB flash drive with a movie loaded on it;
  • allow you to record broadcasting;
  • many models are connected to the Internet (via cable or Wi-Fi), which opens up access to YouTube, IPTV channels and other services;
  • there are devices running on Android OS. With such a set-top box, it is easy to make Smart from a regular TV.

Digital receiver for TV.

For old TV sets, the receiver is usually connected using RCA. For new models, it is preferable to use the HDMI interface, tailored for high quality content. Take the corresponding cable separately.

The digital set-top box makes it possible to view domestic and foreign channels even without an antenna. In this case, weather conditions do not affect the signal quality. There are 2 ways to tune TV channels.

What you need to connect

To connect to the broadcasting of the new standard, you will need certain equipment. It will be easier for those who have a TV from the latest models at home, which already has an adapter that decrypts the incoming signal. With old TVs it is more difficult. you will have to buy a separate receiver, or even change the antenna. The cable also plays a significant role in the stable operation of the system.

  • cable antenna. There is one piece of advice here. if the operator’s tower is located close to home, you do not have to spend money on an expensive model. An ordinary indoor antenna will suffice. If the connection is made to a high-rise apartment, it will not be needed at all, since it is already installed on the roof;
  • signal amplifier. In order for TV channels to be displayed clearly and without interference, they take a device with a 12 V power supply. Some manufacturers deliberately lower the voltage to 5 V, which should be checked immediately in the instructions. The amplifier is a necessary thing if the TV receiver displays the message “No signal”;
  • tuner. This is the name of the receiver. On new TVs, it is the default. The device “contacts” the operator, after which the subscriber gets access to a large number of channels;
  • cable. It connects the antenna to the TV receiver. If the TV model is old, take a cable with an S-Video or RCA connector. For newer ones, HDMI is preferred. It is worth noting that RCA, better known as tulips, does not provide high image quality. The picture will look the same as on analogue broadcast. To improve the signal (provided that there are no HDMI connectors), they buy adapters.

HDMI cable.

Further setup on TVs from Samsung and other manufacturers is simple, which you can handle yourself without the help of technical specialists.