How to glue glass on samsung.

How to stick a protective glass yourself. 5 simple steps

I have long planned to stick a protective glass on my smartphone. I know that for some people the process of gluing turns into torture, because it does not always work out a procedure without jambs. Especially when there is no spare protective glass. So I decided to share with you a simple and effective way that I have been using it myself for several years.

Preparing for this responsible process, for some reason I remembered how I glued films 10 years ago working in the service center. I remember, in the first pairs, not the best results were obtained. either air bubbles, then hairs and dust fell under the film. Years later my gluing skill was well honed. And today I will tell a life hack that will answer the question of how to stick protective glass at home. My guide is suitable for owners of both smartphones on Android and iPhone to users.

Before we start, I want to say about the glasses themselves. The fact is that even if all the rules are observed, the result can upset you. And it’s not even a skill, but in the glass itself.

First you should take the necessary inventory. And so, we will need:

• Protective glass on the phone;
• Maslar adhesive tape;
• Double-sided tape;
• Scissors;
• Microfiber fabric or other soft rag.

In fact, you can do without all this, here is a matter in technology

Advice! I recommend glue in the room without wind and dust. Thus, the probability of dirt falls under the glass decreases almost to zero.

Step 2

Now the protective glass should be attached to the display. See how you would like it to lie. Ideally, it should be in the center, smoothly streamlining the front camera. The more the shift aside, the more curve everything will stick. After that, we grab on one side with masking tape the glass itself. Thereby we fix the position of the glass. Thus, it will lie down as we need.

Some time ago, I already wrote about protective glass for smartphone screens and their advantages over protective films. There were quite a few Комментарии и мнения владельцев, someone stated that it was generally pointless to glue something on the phone. If you think so, then this post is not for you. But among those who gave advice on how best to glue, no one told the method that I will talk about below. I came across it relatively recently. And maybe I will present the “captain’s obviousness”, but, I hope, I will be useful to someone.

So, the usual way is to create a moist atmosphere to confuse all the dust (for example, go to the bath and turn on a hot shower), perfectly clean the glass of the phone and quickly, until the new dust came, attach glass. Alas, it is not possible to stick more or less evenly the first time. It happened that the glass had to be peeled off and glued again. This increased the chances of catching dust, and the sticky layer could be damaged. In any case, the plus of the glass is that it hides almost any hairs, dust dust and even air bubbles in a day or two disappear themselves. Particularly confused people can remove particles accidentally caught under the glass using tape. However, as it turned out, there is a method of a simpler “sticker”.

Most often, accessories are included with glass. wet and dry napkins for wiping the screen and a set of stickers. Well, big. for dust particles, ok, and why small (guide sticker). did not understand, and did not think.

And the casket just opened. First you do not need to remove the film from the protective glass. Ideally attach it to the smartphone screen and fix it with these narrowest stickers. Then “turn over” the glass and clean the smartphone screen well (you can still do this in a wet room). Remove the film from the glass and attach to the screen. Ready. Since this method opened to me, glue everything the first time and almost perfectly!

Ask why I am changing the protective glass so often? It’s simple. I ordered a few 0.2 and 0.26 mm glasses for a sample and it turned out that they were terribly fragile. Cracked even if you unsuccessfully put the phone on the table with a display down or hit something in a bag. So I spent them and ordered the usual 0.3 mm and glad again. Yes, they are thicker and not so convenient to perform gestures from the edge of the screen (if the screen of your smartphone is rounded like an iPhone), but I sometimes drop the phone and I do not want to accidentally break the screen.

In the first post, I also wrote about 3D glasses, which are also circulated to the edges, but in the end it turned out to be. The option with a metal edging does not look very good, dirt falls under the edge. Carbox looks great, but too fragile. Plus part of the covers that “go” to the edges of the iPhone, with 3D glasses are incompatible. And I have a lot of covers and I periodically change them.

Preparing the glass of the phone

Wash your hands so that you do not accidentally leave fat prints on the glass and phone.

If you have a protective film, delete it.

Take an alcohol napkin (in our case, this is a napkin from a bag) and treat a centimeter by a centimeter of the entire phone screen without missing a single spot.

Take a microfiber napkin (we had a tiny rag from a bag) and wipe the glass dry.

Look at the phone to the light: whether unprocessed areas, dust particles or villings are left on it. If such are noticed, they can be removed using the sticky side of ordinary transparent tape followed with subsequent processing of the microfiber.

How to choose a protective glass

Your choice depends entirely on financial capabilities. There are two types of protective glasses in total: matte and glossy.

• Glossy. It costs cheaper, gives good protection against falls, but does not in any way prevent scratches and “web”;. It costs more, but protects more effectively from scratches, does not glance in the sun.

note! The degree of protection depends on the thickness of the glass. High-quality glass is made of 5 layers: silicone, restraining, anti-Bill, protective and oleophobic (moisture repellent).

Each layer performs its own function. Together they provide reliable fastening, protection against scratches and chips, protection against moisture, fat, etc.D. All this not only protects against damage, but also simplifies phone care. Even if the device falls and beats, the screen with the glass does not scatter into pieces, and the crack will be completely insignificant.

Install glass 6 steps

It is very simple to install both types of accessories. You will not need to go to a special service center. Follow our instructions.

• Clean the workplace (this is important). Make sure that there is no dust on the working surface: it can fall under the protective glass and stay there. It will be not good.
• Put all the contents of the box on a clean surface, clean the phone screen using a special napkin and tools for cleaning displays. Make sure that the screen has dried up and do not touch it with your hands so as not to leave fat spots and divorces;
• Unpack and prepare protective glass. Disconnect the film from the accessory. The sticky side will come into contact with the phone display. After that, do not touch the glass in the same way. Otherwise, the prints of your fingers will remain on the accessory;
• Gently turn over the adhesive side down. She should not contact in anything. Generally. Bring the glass to the phone’s screen at right angles. The glass should be directly opposite the screen: as smoothly and accurately as possible;
• We glue it. The following actions must be performed clearly and quickly. Gradually glue the glass to the screen. Start on top and move down. Let the film, let the side plots stick it yourself. If you cleaned the phone well, there will be no bubbles;
• Smooth the surface. Take a piece of microfiber or clean tissue. Gently defeat the glued glass, moving from the center to the side sides. Press the phone slightly. This will help eliminate flashing flaws.

That’s all, you are great. Now remove the protective film from the outside of the glass and use the phone. An additional screen should not affect the quality of the image and the reaction of the display to the commands.

What to do if something went wrong

There are situations when it is not possible to completely clear the phone before gluing. In such cases, the responsiveness of the sensor worsens. In this case, you can carefully remove the glass, put it to the side, re.clean the surface of the screen and glue it again.

note! Such a trick can be carried out only once. Removing protective glass is not recommended. it will only be worse.

How to stick a protective glass on your phone correctly

Step.by.step instructions for the correct installation of protective glass on the smartphone include several steps, some of which may be unexpected:

• Prepare the room
• Collect the inventory necessary for the glass sticker
• Wash the hands
• Try the glass
• Process the smartphone screen
• Delete dust
• Install protective glass

Next, we will tell you what all this is needed and how to do it.

Detailed step.by.step instructions

Prepare the room. In order to correctly glue glass or film, it is important to remove dust in the room. If you work in a dusty room, there is a high probability of dusting under glass, which will negatively affect the display of information. It is advisable to carry out wet cleaning, for a while to hang several wet towels or turn on the humidifier. Thanks to these actions, dust will settle under the influence of moisture. It is also better to install glass with the placement of the phone on a flat surface in a convenient position sitting or standing.

Collect the necessary inventory. It is important not to be interrupted in the process of installing glass, so it is better to prepare everything you need in advance: a phone, unpacked glass, degreasing liquid, microfiber napkins, adhesive tape, stationery scissors, a scrap or tape. Typically, the necessary improvised materials, including stickers and napkins. In this case, an additional tool will not hurt.

Wash your hands. It is important to degrease your hands with soap or other cleaners. After washing, you need to wipe your hands dry with a towel or paper wipes. It is important to use a rag, which does not contain small villi and dust. Or use rubber or latex gloves.

Try the glass. Pre.attach the protective glass to the front surface of the phone, align and remember the optimal position.

Process the facial surface of the smartphone. It is necessary to degrease and clean the place to install glass. If napkins are included with glass, remove a damp cloth from the first package and treat the surface. Then remove a dry napkin from the second package to remove excess moisture and stains. In the absence of complete napkins, use antiseptics or alcohol.containing napkins, and then wipe the surface with dry rags dry.

Remove the remaining dust. Often several dust dust falls on the treated surface of the phone. Complete stickers or sticky tape will allow you to collect dust and not leave stains on the surface of the phone.

Removal of dust with clerical tape.

Set the protective glass. Remove the transport film on the back of the glass, keep the glass outside. Attach one end of the glass to the phone. Level the position, then slowly lower the glass. At this time, press your finger or scraper with your second hand to remove air. In conclusion, remove the second transport sticker.

Remove the film.

Attach glass.

Go through a dry rag to remove air residues.

Pros and cons of protective glasses

There are very few minuses at protective glasses. The most important disadvantage is the installation process that can drag on for several minutes and noted your nerves well. In addition, some glasses crack very quickly (sometimes, even during their installation on the screen) or because of the high density of glass, they prevent the high-quality operation of the sensor. However, these shortcomings relate only to low quality accessories!

Our store presents only high.quality protective glasses, which means that they have only advantages:

• excellent protection of the smartphone from cracks and chips as a result of falling and other incidents;
• low price, so that the glass can be changed several times a year, as soon as the scratches begin to strain;
• impeccable appearance: no one will notice that a protective glass is installed on your smartphone.

Protective glass is not a panacea from all troubles, but still it is better than hoping for your luck and dexterity and store a fashionable smartphone without additional protection!

How to glue a protective glass on a smartphone

The screen of any gadget for communication needs to be protected. Even if you purchased the last iPhone model, do not neglect the opportunity to install an additional film on the display. This will extend the life of the phone, will allow him to look attractive longer. Such mechanical damage as scratches, blows will not be scary if you know how to stick protective glass on the phone. The task is not easy, but subject to the instructions, you can do this at home without outside help.

For a beginner, the procedure may seem difficult, but several training will make you a real specialist. It is worth noting that there is no significant difference, we glue the protective glass on the iPhone 5, other phones or tablet models. The procedure remains the same. It is better to start an inexperienced person with the back of the gadget, and then go to the screen.

Necessary materials and tools

If you just purchased a smartphone, it is important to understand how to stick protective glass on the phone. The device display is very sensitive to mechanical damage. Being just in your. the gadget is damaged by coins, fingernails or keys. Even minimal scratches can lead to the appearance of bubbles while gluing. The same goes for situations when you just want to replace the old phone protection.

• alcohol napkin;
• dry rag;
• special liquid for cleaning TV or computers;
• adhesive tape or vacuum cleaner;
• glass.

Step-by-step instruction

An important point is the preparation of the workplace. Choose a room with a minimum dust. The best kitchen or bathroom. There are too many textiles in the bedroom, which attracts particles. This moment prevents the correct process and can complicate the procedure. If you do not know how to glue the protective glass on the phone, follow the points:

• Wash your hands with soap, then lay out a technique, protective glass for 6 iPhone or other phone on a clean smooth surface.
• Before starting the procedure, remove the old film from the device. To do this, pull the edge at an angle of 60 degrees a little.
• With the help of an alcohol napkin or a cloth with a cleaner, remove the pollution from the phone screen. This tool is sold in technology stores or is done independently. To do this, you need to mix 5: 1 water and alcohol, add a little gel for dishes there.
• Rub the display to shine. If there are dust dust, then we walk along the surface with tape or vacuumber.
• We take out the device from the package and remove the film from it.
• Install protection so that it corresponds to the central button of the gadget and the speakers.
• Put with your finger in the center from top to bottom to fix the overhead surface.
• We drive the remaining air from the center to the edges using a credit card or spatula, which often includes.

Do not press too much on the screen to remove small air bubbles. They will disappear themselves within a few days after the procedure. As a result, you should get a smooth, perfectly even coating of the screen. Although tempered glass on the phone has a thickness of only 0.18 mm, it perfectly protects the device from mechanical damage.

Is it possible to re.glue the protective glass on the phone

High.quality surfaces for the iPhone 5s and other models of the gadget can be used again. To do this, carefully remove the glass and treat the adhesive side with ant alcohol. Wipe it lightly with a cloth moistened in such a liquid, and let it drain a little time. Then set protection in accordance with the speaker and button. Light movements from the center to the edges drive air and liquid. Small bubbles will disappear themselves in a day.

The videos below will talk about how at home without the help of a specialist to equip a gadget display. You will learn how to stick protective glasses on phones or tablets. With such a coating, the screen will be reliably protected from negative impact, which will allow it to maintain an attractive look longer. Protection will protect the device from scratches, and also absorb strokes when falling. In this case, the sensitivity of the sensor of your phone will remain the same.

How to avoid dust when sticking glass

At home, before doing the stickers of protective glass, you need to take care of removing dust from the air. To do this, it is advisable in a small closed room (better in the bathroom) to saturate air with moisture (steam) to besiege dust dust. If you have an air humidifier with ionization. this will be an ideal means for cleaning the environment of dust.

It is also worth putting on clothes with fewer piles, for example, a T.shirt. At the same time, it is better to shake it well in advance, and wipe your hands to the elbows with a damp towel.

Preparing the surface of the screen for glass sticker

After all the anti.spine procedures in the room are performed, you can carry a smartphone, adhesive tape, scissors, a napkin for wiping optics and protective glass with accessories. Typically, two napkins come to the glass. wet alcohol and dry, to rub the surface dry.

Try the glass while without removing the protective films from it, carefully impose its desired placement area (if your display has glass rounded at the edges, it is especially difficult to do it) and fix it with pieces of tape in the form of a book cover on the left side of the smartphone body. Check the convenience of opening such an impromptu cover and the accuracy of getting to the right place after closing.

Community rules

It is forbidden to add posts not related to the subject of the community.

The most fucked advice would be. Do this in the bathroom in which turn on the shower for 5 minutes. Then wait a couple of minutes to set the moisture with dust, then go with the phone, wipe the screen and glue. Otherwise, the dust will be shifted every second before gluing.

What to do if immediately after removing the transport canvas, dust settled under the glue under the glass?))

The answer to the post “What kind of conspiracy against bespectacles?»⁠ ⁠

There really is a certain conspiracy of sellers about the glasses. In any network optics, they will tell you that this is the last century, they don’t do it now, take plastic and do not fuck.

over, from the shortcomings of glass, in my opinion, only excess weight. And then this is very subjective. For example, I like that glasses are sitting tightly on the nose and do not blow them off the wind. I don’t know about safety. From the height of my height, they fall and do not beat, and if you have an accident, God forbid, then, to be honest, xs, that he will behave worse and sticks in the eye. Glass or plastic. Well, you wrote everything in the posts in the post.

So, how I do and advise you if you want glasses with glasses. Buy a frame what you want and where you want, even though Gucci there are some most fashionable, even the simplest at the nearest point. And when they begin to offer you the best Japanese plastic with triple spraying in optics, which never scratches, or French, simpler, with double spraying, which, although it scratches once every hundred years, is also very good, then say Thanks and send them nafig. The last argument that they can use, that there will be no guarantee on the frame in which you inserted the lenses on the side. Don’t get fooled, leave.

Now the main question is where to get glass. Somewhere near you, if you live in the city, there should be the so-called social optics. This is the place where visual disabilities are served, pensioners and other categories of citizens who cannot survive without it. But nothing prevents you and you can serve there. There is always glass there, because some particularly complex options for lenses from plastic do not make, well, or very expensive, I don’t know for sure. By the way, there is all the plastic that is offered in network optics and, in my opinion, a little cheaper.

How to find such an optics, closest to you, I don’t know for sure. You can ask pensioners. Here is the one I use in St. Petersburg if anyone needs.

Repair of the knob for manicure. Jammed tsang without a cutter⁠ ⁠

Sister asked to help repair such a thing.

So I found out how the milling cutter looks like a manicure, well, or its working part.

I write a post because my sister did not find a solution to the problem on YouTube. Rearing a video where everything is dismantled, they are promoted and it seems to be possible to fix everything, but somehow not confused and without a bottle of a screwdriver cannot be figured out. And the solution was quite simple. Perhaps someone will come in handy.

When the milling cutter itself is inserted into the zangi cartridge, the black plastic switch (movable part with the inscription RS) clamps the cutter in one position, and in the other releases to get/replace with another. It works on the principle of the switch in a ballpoint handle. And when the cutter is inserted, then you can switch to any condition (open/lock), but if you pull the cutter to switch it to the cutting position of the milling cutter (LOCK, direction “S”), then back to Open (direction “R”) already Do not switch.

Inexplicably. There is a bunch of small details and springs and the tip of the tsangi itself in this case falls a little down. Maybe this is the problem of this particular handle model. I do not know.

Вдруг я неправильно какие-то части называю, уж простите, что такое фрезер узнал позавчера 🙂 Названия некоторых деталей гуглю по ходу написания поста.

I unscrewed the upper tip of the metal. Pancakes, bushings, couplings, springs. There is a chance that everything can fly apart, so I took a picture of the filling, so that it was possible to collect it correctly.

Remove the plastic switch further. We see it under it. The groove for which it is fixed on the metal part of the switch is not at all deep. Therefore, to attach power if so jammed tsang, I do not advise.

These round washers on the sides. This is what I wrote above the Lock/Unlock switch working on the principle of the switch in the ballpoint handle as I understand. There are 2 pieces on both sides, fixed only by the switch body, without it they easily jumped off the axis and roll away where they want.

Then I decided to collect everything as it was. And while collecting he realized that the problem had already been solved.

one. Weaken the switch. We spin on 2-3 revolutions the case of the tip of the handle of the milling.

After that, the case of the rotary sleeve switches without problems translates into the Open mode (direction “R”)

We twist the tip of the tip in the opposite direction to the stop.

four. After twisting the body, the milling cutter enters the tsang as expected.

Now you can not be afraid to accidentally block the switch when the milling cutter is not inserted.

Инструкция разблокировки картинкой:

Perhaps many manicurers know this way to eliminate the malfunction. But since something needs to be disassembled/promoted to restore performance, this is clearly not a normal and not standard way to solve the problem. Therefore, if someone comes in handy. So I wrote not for nothing.

Buying and using motor oil from an official dealer. Council from a former employee ⁠

As a rule, when passing maintenance by an official dealer, you are offered to use the oil that the official dealer sells.

Most dealers buy oil in barrels, because it will be more profit, more convenient and similar.

If possible, I advise you to buy only sealed oil from them. Then I will tell you why.

To get the admission and status of an official dealer of cars of a certain brand, in most politicians, the dealer must purchase original spare parts from the manufacturer, all this is spelled out in the dealer agreement. During the work, the dealer makes many reports (which, by the way, can be successfully drawn, but for this case there are a bunch of checks that can come at any time), the reports have information about the number of cars that came for one or just changed oil. Based on this information (and a bunch of nuances), the manufacturer’s managers consider how much oil the dealership must purchase to fulfill the terms of the dealer agreement, in simple words they put a plan, which is usually overestimated. Even if the plan is overstated, dealers fulfill the plan because fines for non.compliance are possible. Some representative offices have a good discount, if you fulfill the plan for a long time and more profitable to buy goods with excess than to break this discount.

Thus, if the service you arrived in really has the status of an official dealer, they must have original oil.

And now I will tell a couple of moments why I advise you to buy sealed canists and it is even desirable for your presence in the repair zone at the time of oil filling the car engine. (In general, it is desirable that the canister be opened with you).

In one of the centers in which I worked, they purchased oil in barrels. Castrola, and it was sold like original Ford oil. That is, if you came to buy Castrola oil, the cost will be, for example, 3.000r, but if you ask for the original Ford oil, the cost will be 5.000r (oil will be from one barrel.) Naturally, no one will let you into the barrels, and most likely there will not even be any marking on the barrel. If you ask for a certificate of conformity for oil. it will be printed (the “drawing” has already been prepared in advance) and put the seal of the warehouse. If you do not know who the manufacturer of the engine oil is precisely for your car brand. Look on the Internet, and do not overpay in the future.

Inventory in warehouses is carried out, and it is carried out very carefully and often quite often. It was not in my service, but nearby. During the inventory, naturally from the barrels, the oil is not drained, but measurements are made differently. In one service, the storekeepers, apparently carried away by the left sale of the oil from the warehouse, and during the checking of the oil in the barrel, well, there was not enough. Leveled the lack of ordinary water. After checking, the water was sucked out. Climax: on one of the client cars, the engine jammed, the car was very expensive. apparently the water was not completely removed. Examination showed. low.quality oil was used.

I gave only 2 simple examples of what could be with oils of barrels, but there are much more of them.

Perhaps you want to bring your oil bought from “proven” sellers. If the car is under your guarantee, I do not advise you to do this, in the event of an engine breakdown. this will be opened on the history of car service and it will be difficult for you to prove that the oil was good, but it was possible to prove in my practice such cases.

I don’t want to scare, I do not inspire distrust of dealers. A lot of dealers work honestly and absolutely transparent. These cases are extremely rare, but they are.