How to connect wireless Sony headphones

Article

Initialize the headset to restore the factory settings Unplug the micro-USB cable, turn off the headset, then press and hold the and buttons simultaneously for more than 7 seconds. The indicator (blue) will flash 4 times ( ), and the settings, such as volume, will be reset to the factory settings.

The reasons why the Bluetooth module is not detected by other devices include the following: The device is in off state. Bluetooth discovery is disabled in the settings. Long distance between the receiver and transmitter.

The headset’s left/right earbuds have a full charge time of approximately 1.5 hours. If the light (red) on the charging case flashes and turns off right away when you put the headset in the charging case, that means the remaining battery in the charging case is low and the headset cannot be charged.

Connecting to a matched Bluetooth device

  • Turn the headset on. Press and hold down the button for approximately 2 seconds. Make sure that after you remove your finger from the button the light is still blinking blue.
  • Perform a Bluetooth connection from a Bluetooth device. See.

How to Connect a Wireless Bluetooth Headset to the TV

For a long time I did not want to write this article, and not because I was lazy, but because the topic of how to connect Bluetooth headsets to TVs with Smart TVs is very “dark. It all started when I bought myself some Bluetooth headphones and connected them to my Philips TV, which runs on an Android TV. It is very easy to connect without any problems. I thought why not write detailed instructions on how to connect wireless headphones to televisions. And I found out that many modern televisions support Bluetooth.

But it seems that I did not want to write only about Philips TVs. I decided to make a general guide and show how to connect Bluetooth headphones to LG, Samsung and Sony TVs. I do not own these televisions and I cannot test everything on my own experience so I started searching for information on the Internet. And then it began. If the Philips and Sony TVs that run on Android TV have no problem connecting with wireless headphones, then LG with webOS and Samsung Smart TV is a mess.

It is clear that the TV must have a built-in Bluetooth adapter. But you probably know that almost all televisions work only with original equipment (cameras, adapters, remote controls, etc.). д.). With headphones, it’s roughly the same story here. LG and Samsung TVs can be connected to the original Bluetooth stereo headset without any problems. But you can hardly plug in standard headphones. But it depends on the TV model, series, firmware version, year of production and a lot of other things. Such a mess that studying this topic for a few hours made my brain boil.

How to pair SONY MDR-ZX330bt bluetooth headset to Samsung Android

It seems that in the newer models of Samsung TV you can connect any Bluetooth headphones. There is also a service menu where you can try to enable this function. But then again, it all depends on the series and model. LG has about the same story. And if you believe LG’s support, you can only plug in original headphones. But again, not on all models.

To avoid confusion, I will divide this article into three sections. I will tell you about each manufacturer separately. I’ll show you how you can try to connect Bluetooth headphones in the TV settings.

If your TV does not have Bluetooth, or it flatly refuses to see headphones, you can use a special Bluetooth transmitter that connects to the 3.5 mm TV output (also available to connect via RCA (RCA), or optical audio output). and it is already connected to the headphones. About these adapters I will tell in more detail at the end of the article (or read the article about Bluetooth transmitters at the link above).

How to connect wireless headphones to the phone

connect, wireless, sony, headphones

Wireless headphones are one of the most convenient inventions of the XXI century, which solved the problem with the constantly tangled in a or backpack cords. Now those who want to be constantly in touch, listen to music and audiobooks on the road or when playing sports, choose from a wide range of Bluetooth-headset. And no matter what device you bought, to connect wireless headphones to the phone is not difficult, the producers have tried to make this process as intuitive as possible. But a beginner may be frightened by the complexities and even appear to be signs of breakage. We tell you how to connect wireless headphones to your Android or iPhone smartphone and provide step-by-step instructions explaining all the technical complexities.

How to connect wireless headphones to your phone?

Wireless headsets can be connected in two ways: standard and advanced. In the standard method, the connection is made through the settings menu of the mobile device. The user does not need to download third-party apps, just activate the Bluetooth headset and confirm the pairing. In this case, there is no access to some of the settings provided by the headset manufacturer.

For advanced connectivity, use the headphone or smartphone manufacturer’s tools: Sony | Headphone Connect, Samsung Level and Motorola Connect. These programs allow you to make advanced settings and inform you of the remaining battery charge. If the app is not pre-installed, you need to download it from the official website or from Google Play or AppStore.

How to turn on the headphones?

To activate the headphones, locate the power button on the case or on the headphones themselves, or simply open the case and pull them out. Then place one or both earphones in your ears. Once you find the button and press it, hold your finger down for a few seconds until you hear a ringing tone in your ear or until the LED on the headphones starts flashing.

Often the headset has two lights: a blue and a red light. The blue light means that the device is on, but is not yet ready to find new devices, but can connect to devices that have previously been connected to it. The flashing red LED means that the device is on and ready to search for new devices.

Preparing the headphones to connect to your phone via Bluetooth

To begin, the headphones simply need to be turned on. On regular headphones that are not separate, there is a separate button for this. There should be a beep and/or a light on/blinking.

If you have TWS headphones that are separate, they usually come on as soon as you take them out of their cases. This is also usually signaled by a beep, or an indicator. If you take the headphones out of the case and they do not turn on (but they are charged). then press the button on each earphone for 3-6 seconds. Make sure you take out both headphones!

For some models you just need to open the charging case. For example, in the case of Airpods.

How to connect wireless Bluetooth headphones to the TV?

Here are the instructions on how to connect wireless headphones to your TV if your TV has Bluetooth built in (built-in Bluetooth module).

  • Turn on the wireless headphones and the device search mode on the headphones. Usually you have to hold the power button for 5-15 seconds from the off position until you hear a beep. Or a separate Bluetooth button. In TWS, it’s a button on the case or opening the case. For more information on pairing, see our instructions or your headphones documentation.
  • Go into the TV settings and search for Bluetooth devices. Usually you can do this in the sound settings, there should be audio device options: audio output, device speakers, speakers, and the like. Bluetooth should be among them. Or just in connectivity options.
  • In the Bluetooth device list submenu (may be a similar name, found in the devices or sound menu), select your wireless headphone model.
  • Pairing (connecting). Done! Bluetooth headphones are connected to your TV.

This general guide on how to connect wireless headphones to your TV will work for any TV with Bluetooth built in. With different TV models, the setup is different, but the principle is the same.

Why won’t your phone see your wireless Bluetooth headphones?

One of the most popular problems you can bump into when connecting headphones to your phone is when your phone doesn’t see your wireless headphones, which are connected via Bluetooth. This problem is true for Android phones as well as for the iPhone. And with the advent of the separate TWS format Bluetooth headphones, these problems have become even greater. First of all, a lot more people have started to use wireless headphones, use them as a headset. Secondly, TWS headphones are technically more complex, and their connection is not uncommon to have problems.

In this article I will explain what to do when your phone can not find your Bluetooth headphones or headset. It just can’t see them in the list of available Bluetooth devices. And which you may have seen before and they plug in.

The article will talk about as TWS headphones (when the two headphones are separate). and about conventional wireless headphones. Solutions are suitable for different Android smartphones: Samsung, Xiaomi, Honor, OPPO, Huawei, etc. д. These solutions are also suitable for the iPhone. As for the headphones themselves, the manufacturer and model does not matter: JBL, Sony, Honor, Xiaomi, Motorola, QCY, Chinese i7s, i9s, i10, etc. д.

Check if your headphones are not in the list of connected Bluetooth devices

Perhaps the headphones are connected, but there is no sound. Without closing the Bluetooth settings looking for your headphones in the list of devices.

  • If they are connected, as on the screenshot above, add sound on the phone and headphones. It can be just turned to minimum. If this does not help, you can disconnect and reconnect the headphones from this menu.
  • If they are not connected, but are visible in available devices, pair. If the pairing has been lost for some reason. And you need to reconnect them as you did the first time.