How to change the language in a Xiaomi router

LAN settings

It is important to correctly configure the local network, paying special attention to the DHCP protocol, because it provides automatic receipt of settings after connecting devices to an active network. What kind of settings it will provide is up to the user himself in the “LAN setting” section. In addition, the local IP address is edited here.

Then go to “Network Settings”. This is where the DHCP server parameters are determined, which we talked about at the beginning of the article. obtaining DNS and IP addresses for clients. If there are no problems with accessing the sites, leave the marker next to the item “Configure DNS automatically”.

Go down a little lower to set the speed for the WAN port, find out or change the MAC address and put the router into Switch mode to create a network between computers.

Preparatory work

You have purchased and unboxed a Xiaomi Mi 3G. Now you need to start choosing a place for him in an apartment or house. The connection to high-speed internet is via an Ethernet cable, so it is important that it is long enough. At the same time, take into account the possible connection with a computer via a LAN cable. As for the wireless signal of the Wi-Fi network, thick walls and working electrical appliances often interfere with its passage, so take this factor into account when choosing a location.

Connect all necessary cables to the appropriate connectors on the router. They are located on the back panel and each has its own name, so it will be difficult to confuse the location. The developers allow only two PCs to be connected via cable, since there are no more ports on board.

Xiaomi Mi WiFi 3 Router Change language from chinese to english HD

Make sure your operating system’s system settings are correct. That is, the IP address and DNS should be provided automatically (their more detailed configuration takes place directly in the web interface of the router). You will find a detailed guide on configuring these parameters in our other article at the following link.

Checking the functioning of Xiaomi Mi 3G

Now you need to make sure that the Internet is working normally, and all connected devices are displayed in the list. To do this, open the “Status” menu and select the “Devices” category. In the table you will see a list of all connections and will be able to manage each of them, for example, restrict access or disconnect from the network.

The Internet section displays basic information about your network, including DNS, dynamic IP address, and computer IP. In addition, there is a tool here that allows you to measure the connection speed.

Configuring the Xiaomi Mi 3G router

We figured out the preliminary steps, then we will proceed to the most important part of today’s article. configuring the router to ensure a stable Internet connection. It’s worth starting with how to go into the settings:

Launch Xiaomi Mi 3G and in the operating system expand the list of available connections if you are not using a wired connection. Connect to the open Xiaomi network.

Open any convenient web browser and enter miwifi.com in the address bar. Go to the entered address by pressing Enter.

You can change the name of the wireless network and set a password. Check the corresponding box if you want to set the same access key for the point and the web interface of the router. After that, you need to save the changes.

Next, enter the settings menu, specifying the login and password of the router. You will find this information on a sticker located on the device itself. If you specified the same password for the network and router in the previous step, mark this by checking the box.

Wait for the hardware to restart, after which it will automatically reconnect.

You will need to re-enter the web interface by entering the password.

If all actions were performed correctly, you will be taken to the parameter editing mode, where you can already start further manipulations.

Wireless settings

In the previous instructions, we described the process of creating a wireless access point, however, further detailed editing of the parameters occurs through a special section in the configurator. Pay attention to the following settings:

Go to the “Settings” tab and select the “Wi-Fi settings” section. Make sure dual channel mode is enabled. Below you will see a form for adjusting the main point. You can change her name, password, adjust the security level and 5G options.

Below there is a section on creating a guest network. It is necessary when you want to make a separate connection for certain devices that would not have access to the local group. Its configuration is carried out in the same way as the main point.

Updating the firmware and changing the interface language

Configuring a router with a Chinese web interface is not convenient for all users, and the automatic translation of tabs in the browser does not work correctly. Therefore, you need to install the latest firmware to add the English language. This is done as follows:

The screenshot below shows the “Main Menu” button. Left-click on it.

Go to the “Settings” section and select “System Status”. Click on the button below to download the latest updates. If it is inactive, you can immediately change the language.

After completing the installation, the router will reboot.

You will need to go back to the same window and select “English” from the pop-up menu.

Configuring the Xiaomi Mi 3G router

The Chinese company Xiaomi, well-known to many, currently produces a wide variety of equipment, peripherals and other diverse devices. In addition, their product line includes Wi-Fi routers. Their configuration is carried out according to the same principle as with other routers, but there are subtleties and peculiarities, in particular, the Chinese language of the firmware. Today we will try to make the entire setup process as accessible and detailed as possible, as well as show the procedure for changing the language of the web interface to English, which will allow you to make further editing in a more familiar mode for many.

Security options

Above we have discussed the basic configuration procedure, but I would like to touch on the topic of security. In the “Security” tab of the same “Settings” section, you can activate the standard protection of the wireless point and work with address control. You select one of the connected devices and block its access to the network. Unlocking takes place in the same menu. In the form below you can change the administrator password for entering the web interface.

Xiaomi Mi Wi-Fi Router 4 authorization

After connecting to the network, you need to go to the router. To do this, open any browser (be it Google Chrome, Mozilla Firefox, Internet Explorer, etc.). Looking ahead, I will say that through Google Chrome it will be possible to translate the interface into Russian through a special extension. In the address bar of the browser, enter 192.168.31.1 and press the “Enter” button on the keyboard.

The router interface opens, where we are asked to log in, that is, to drive the password into the router interface, if forgotten, this is the same password that was configured above. If you checked the box, then it matches the password on Wi-Fi.

Translation of the Xiaomi Mi Wi-Fi Router 4 interface into Russian

There is a trick how you can translate the Chinese language of the Xiaomi Mi Wi-Fi Router 4 into Russian, but this requires an Internet connection. To do this, you need to: 1. Log in to the router through the Google Chrome browser, then follow the link: https://chrome.google.com/webstore/detail/rumiwifi/mbiehbednoakmhlmjcpgpciocekdjabp?utm_source=chrome-ntp-icon and install the extension to the browser:

After installation, at the top right of the browser, you will see an icon with the Xiaomi logo, you need to click on it, thereby the extension is activated and the text of the interface of the Xiaomi Mi Wi-Fi Router 4 will be automatically translated from Chinese into Russian:

Configuring L2TP on Xiaomi Mi Wi-Fi Router 4

Go to the interface menu and click on “Advanced”, then on the “VPN” icon, then on the “Add service” button.

Xiaomi Mi Wifi 3c Router Change Language From Chine To English HD Full Tips Tricks N Tutorials.

In the pop-up window in the “Protocol” line, select “L2TP” 3. In the “Name” line, write any word in Latin, below, in the “Server” line, indicate the server ip-address, “Username”. Username, “Password”. Password. All of the above data is provided to you by the provider (the Organization that conducted the Internet for you). All these data are usually written in the contract with the provider. If for some reason you could not find them, you need to call the provider’s hot line and find out how you can get them. 4. Click “Save”. save the settings.

How to Change Xiaomi MI Router Language Chinese to English | Nazmul TECH

Setting up a Wi-Fi password on the Xiaomi Mi Wi-Fi Router 4

The Wi-Fi password was configured above, so I’ll show you where the settings are located. Go to the menu and click on “Settings”, then on “Wi-Fi settings”. If you want to correct network names or change passwords, you can do it here:

Configuring PPTP on Xiaomi Mi Wi-Fi Router 4

Go to the interface menu and click on “Advanced”, then on the “VPN” icon, then on the “Add service” button.

In the pop-up window in the “Protocol” line, select “PPTP” 3. In the “Name” line, write any word in Latin, below, in the “Server” line, indicate the server ip-address, “Username”. Username, “Password”. Password. All of the above data is provided to you by the provider (the Organization that conducted the Internet for you). All these data are usually prescribed in the contract with the provider. If for some reason you could not find them, you need to call the provider’s hot line and find out how you can get them. 4. Click “Save”. save the settings.

Connecting the Xiaomi Mi Wi-Fi Router 4 to a computer with setting a password for Wi-Fi

The Xiaomi Mi Wi-Fi Router 4 does not come with a patch cord, that is, a cable that would connect from the router to the computer. Therefore, to configure the router, we will connect via Wi-Fi. We connect the router to power.

In the lower right corner of the desktop, we find the wireless network icon. 2. Find an unprotected Xiaomi network. Xiaomi_xxxx_xxxx, instead of “x” there will be a set of letters and numbers. We connect to this network:

After that, a window will appear with loading the initial settings:

We see the welcome window, where you need to check the box and click on the button with Chinese characters. Here we agree to the terms and conditions of Xiaomi.

Getting started setting up a password for a wireless Wi-Fi network.

In the image under item 1. we assign a Name to the wireless Wi-Fi network, 2. Come up with any password for the wireless Wi-Fi network, there must be more than eight characters. 3. If we check the box here, we assign this password from Wi-Fi to the password on the router interface, that is, to enter and configure the router, we will need to enter the same password as on Wi-Fi. 4. after entering all the data, click on this button, which means “Save”. These settings will be applied to both networks (2.4 GHz and 5 GHz), since this router is dual band.

After saving the wireless network settings, we are given the following settings, these are the settings of the parameters for entering the router. A step earlier, we assigned a password from Wi-Fi to the password for entering the router, here we can change it:

I will write down what is in the picture 1. Login from the router, I advise you to leave it the same, 2. Password to enter the router, 3. One password with a Wi-Fi network, 4. Next. After applying the settings, the router goes to make changes and reboot:

Now you need to reconnect to the wireless Wi-Fi network, since we changed the network name and protected it with a password. To do this, again in the lower right corner of the desktop, click on the wireless network icon:

We call the network any word in Latin, for example “Sultanov”. Do not forget to check the box next to “Connect automatically” and click on “Connect”.