How To Change Battery On Iphone 5s

Essential Tools for iPhone 5 / S Battery Replacement

Replacing the iPhone 5 battery is not a very complicated procedure. If you are doing it for the first time, then you will need special tools to disassemble the Apple equipment. Professionals can handle with versatile tools.

To replace the battery, you must have:

• Pentalobe and Phillips (1.2mm, 1.3mm, 1.6mm and 1.7mm) screwdrivers.
• Suction cup.
• Plastic tool.
• Scissors.
• Tweezers.
• New battery for iPhone 5.

When to change the battery?

Everyone knows about the natural wear and tear of battery capacity. If a new original battery can last 2-3 years without replacement and a significant loss of charge capacity, then non-original ones can be safely changed once a year.

There are certain nuances in which it is necessary to replace the battery:

• If the iPhone 5 / 5S turns off when the charge level is more than 20-30%, and during switching on, a screen is displayed that signals the low battery.
• If the smartphone becomes discharged at the same time by 2 3% or more.
• If the display starts to move away from the case or cracks appear on the device.

The last sign may indicate other malfunctions, but if you have not dropped the phone, then the bulging battery may burst into the case. During operation, the battery emits gas, which accumulates under the shell and inflates it slowly.

How to replace the battery (accumulator) iPhone 5 / 5S

Let’s see how to replace the iPhone 5 / 5S battery with a new one and what tools you need.

We immediately warn you: we are not responsible for your actions. Better contact the service.
P, blockquote 2,0,1,0,0.-

And if you decide to change it yourself, then make sure that your battery is original or at least of good quality. Otherwise, your iPhone may burn out or work incorrectly, constantly shutting down or rebooting.

How to replace battery on iPhone 5?

The instructions below are relevant for the iPhone 5, 5C and 5S gadgets. These devices are very similar in design. We carry out the following steps:

• Unscrew the two 3.9 mm Pentalobe screws next to the Lightning connector.

On the iPhone screen, attach the suction cup slightly above the Home button. Check that the suction cup is attached tightly. The front must be secured with clamps. Your goal is to detach the clips without damaging the cables that connect the front and back of the gadget. Proceed with the utmost care and be very careful.

Pull the suction cup up and hold the bottom of the iPhone to separate the bottom of the front panel slightly from the case. Using a plastic tool, gently pry off the edges to detach the back from the front. On the iPhone 5s, the front panel is attached to the back more tightly than on most other gadgets. Do not try in any way to completely detach the front panel from the back of the case.

• Detaching the suction cup from the iPhone display.
• Raise the front part of the case a little so that you can disconnect the cable that leads to the Home button. The train must not be pulled. If you tear it, the Touch ID fingerprint scanner will not work afterwards. It can only be restored by Apple Service Center employees.

Using tweezers, remove the bracket from the connector.

Disconnect the ribbon cable with tweezers. It is necessary to check that you do not detach the entire connector, but only the cable.

When the cable is detached, you need to open the gadget case at an angle of 90 degrees. It is recommended to lean the front part against something, for example, an iPhone package. For added security, it can be secured with an elastic band. This will prevent undue stress on the cables.

Unscrew the two 1.6 mm Phillips # 000 screws holding the metal plate that secures the battery connector to the system board.

We take out the plate with tweezers.

Using tweezers, carefully lift the battery connector out of the socket on the system board. Care must be taken not to let the jack rise.

Remove the following screws: one 1.3 mm Phillips # 000 screw, one 1.2 mm Phillips # 000 screw, one 1.7 mm Phillips # 000 screw, one 1.7 mm Phillips # 000 screw. The 1.7mm screw is not magnetized to the magnetic screwdriver. Don’t lose it. During assembly, you need to make sure that the screws are in place. If you accidentally use a 1.3 mm screw instead of 1.7 mm, this can seriously damage the motherboard, which will make the gadget unusable.

Using tweezers to remove the metal cover.

Detaching the sensor cable and front camera.

Hold the bezel to disconnect the display cable.

Disconnect the touchscreen connector. The bezel will then detach completely from the back.

Using a plastic spatula, we pass between the battery and the headphone jack. This is necessary to expand the label on the battery.

Pulling out a small piece of duct tape.

On the tape we make an incision between the two white stripes.

From under the battery, slowly pull out one of the adhesive strips. Pull gently while maintaining constant tension. To facilitate the process, it is recommended to pull the tape at an angle of 60 degrees or less.

We do a similar operation with the second tape.

• When installing the battery, stick the adhesive tape on the back of the battery.
• After installing the battery, you need to reassemble the gadget.
• After.-

  An active user of “apple” products, able to repair any Apple gadget and give advice on the work.

  Have questions? Ask in the comments to the article.

  How to change the battery on an iphone 5s

  Using this guide, you can replace your iPhone 5s battery at home.

  Attention! Perform these steps only if you have the appropriate skills and experience.

  When installing a new battery, use double-sided tape for extra protection. It will provide extra density and prevent the battery from moving inside the case.

  Step 1. Front panel. If the display glass is broken, to prevent it from shattering and not getting hurt while disassembling the gadget, stick transparent tape on it. Make sure that the tape is glued to the entire surface of the smartphone screen so you will keep it intact.

  Step 2. Power down the iPhone before disassembling. Unscrew the two screws at the bottom of the case, they are located on either side of the charging connector at the bottom of the case.

  Step 3. This and the next steps demonstrate the process of using the iSlack, which is specifically designed to safely open the iPhone case. If you don’t have one, skip to Step 5. Close the iSlack handles to open the gap between the suction cups. Place the bottom of the iPhone between the suction cups against the plastic depth gauge. The top suction cup should be positioned directly above the Home button. Open the iSlack handles to close the suction cups. Make sure they are located in the middle of the smartphone body.

  Step 4. With one hand, hold your iPhone securely, and with the other, slowly press down on the iSlack handles to separate the top from the bottom. If you opened the gadget using iSlack, you can proceed to Step 8.

  Step 5. Manual opening of iPhone. If you don’t have an iSlack, you can use a regular suction cup to remove the top panel. Attach a suction cup to the screen just above the Home button. Make sure the suction cup is fully attached to the screen to get a secure grip.

  Step 6. The front panel is secured with snaps, and there are also several rubber cables that connect it to the rest of the gadget. Your task is to open the latches and lift the upper part only slightly, in order to then disconnect the cables. Work carefully so as not to damage the cable fixings. Holding the bottom of the iPhone in one hand, pull up on the suction cup to gently detach the edge of the Home button from the bottom. Using a plastic opening tool, carefully detach the top of the case from the bottom while lifting it up by the suction cup.

  Step 7. Do not try to completely detach the top of the iPhone from the bottom as they are still connected by multiple cables. Click on the middle of the suction cup to release air from under it. Carefully remove the suction cup from the display.

  Step 8. Open the phone just enough to access the metal brace that covers the button cable. Do not open the phone too wide as you risk damaging the home button cable or the connector to which it is connected. Damage to the “Home” button and its subsequent replacement will no longer allow using the Touch ID fingerprint scanner. Using the sharp tip of a plastic spatula, pry up the metal bracket and remove it with tweezers.

  Step 9. Using the pointed tip of a plastic spatula, disconnect the home button cable from the port. Be careful not to pull the connector itself away from the board it is attached to.

  Step 10. After the cable is disconnected, lift the bottom edge of the cover up, using the top edge as a hinge. During the next few steps, until you completely detach the cover, keep it raised 90 degrees in relation to the bottom.

  Step 11. Remove the following screws that secure the cable cover bracket to the top of the base: one 1.7mm screw, one 1.2mm screw, one 1.3mm screw, and another 1.7mm screw. In this step, it is extremely important to remember the correct location of the screws. Accidental use of the wrong screw in the upper right corner while assembling may damage the smartphone’s motherboard.

  Step 12. Disconnect the cable cover at the top of the base from the motherboard.

  Step 13 Using the wide end of a plastic spatula, disconnect the front camera and sensor cable.

  Step 14. While supporting the top of the smartphone, disconnect the screen cable from the connector. When reassembling, incomplete connection of the connector and connector may result in the screen not displaying the picture. In this case, you will need to disassemble the smartphone again and reconnect the connector to the connector.

  Step 15. Disconnect the digitizer cable connector.

  Step 16. Detach the top panel from the bottom.

  Step 17: Remove the two 1.6mm screws that secure the bracket that covers the battery connector to the motherboard.

  Step 18. Disconnect this bracket from the iPhone board.

  Step 19 Using the flat side of a plastic spatula, carefully pry the battery connector from its connector on the motherboard.

  Step 20 Using the sharp end of a plastic spatula, peel off the battery tape by inserting it between the battery and the headphone port.

  Step 21. Detach the adhesive tape from the phone. Cut this tape in between the two white stripes.

  Step 22 Pull the inner duct tape up. Do not twist it, try to pull it straight up. Pull it at a 45 degree angle to remove the tape from under the battery.

  Step 23: Pull the outer edge of the duct tape from under the battery perpendicularly up until it comes off the phone.

  Step 24. If one of the adhesive strips breaks and the battery remains inside the case, use the dedicated iOpener or use a hair dryer to heat the smartphone case right behind the battery. This will loosen the battery attachment to the case.

  Step 25. Insert the plastic card between the battery and the case from the side where the battery is located at the edge of the case. Do not insert the card where the battery is adjacent to the motherboard, you may damage your smartphone. Then push down on the card a little harder to peel off the adhesive tape located under the battery. You can also use dental floss or a thin guitar string to peel off the tape by gently prying it under the battery.

  It’s easy to do everything yourself and you don’t need to go to the service.

  Notice that your iPhone 5s battery is draining faster? It is likely that the battery has already lost its properties and it is time for it to rest (how to check). In this guide, we went over the process of disassembling the iPhone 5s and replacing the battery in it.

  Step 6: Replace the screws that secure the display module.

  Use a five-star screwdriver to tighten the two screws that were removed first. They are located on either side of the charging connector.

  What you need to replace the iPhone 5s battery

  You will need a new battery and a small set of tools. I recommend using only a quality battery from a trusted supplier like NOHON.

• New battery
• Sucker
• Screwdriver asterisk
• Phillips screwdriver # 000
• Plastic spatula
• Straight razor or fine-bladed knife

Step 4: replace the battery

1: Using a # 000 Phillips screwdriver, remove the two screws securing the battery connector protector.

2: Carefully remove the iPhone 5s battery connector protector and set it aside.

3: Using a plastic spatula, carefully disconnect the battery cable from the board.

4: There is an adhesive tab along the bottom of the battery. Use a plastic spatula to unfold it.

5: Pull the tab to loosen it enough and use scissors to cut it in half.

6: Gently pull the first tab along the left side of the iPhone 5 battery. It will release from under the battery. Do not worry when you hear a creaking noise, this is normal as the glue cracks.

7: Slowly and carefully pull the second tab along the right side of the battery. Do not pull on the tab too quickly, it will be more difficult to remove the battery if it comes off.

8: Once the tabs are completely free, simply remove the old battery from the iPhone 5s.

9: Install a new battery. Do not forget to stick the double-sided tape that comes with the battery on the back of the battery.

10: Connect the battery to the motherboard.

11: Replace the connector protector and tighten the two screws that were removed earlier.

Step 1: Disconnect iPhone 5s

Before starting any repairs on any device, remember to always turn off the device. Just hold down the power button until the Power off slide appears. Once you make sure the iPhone 5s is turned off, proceed to the next step.

What is needed

• Phillips (1.2mm, 1.3mm, 1.6mm, and 1.7mm) and Pentalobe screwdrivers.
• Plastic tool.
• Sucker.
• Tweezers.
• Scissors.
• New battery for iPhone 5s.

How to tell if your iPhone battery needs replacing

Our iPhones do a tough job every day. They can simultaneously pick up a signal from GPS and GLONASS satellites, download data using a high-speed LTE connection, take photos with flash and display it all on an incredibly clear screen. All this is a strong blow to the smartphone battery, which squeezes everything out of itself every day. Over time, he has less and less strength, as a result of which we begin to charge the smartphone more often. It just so happened that after just 1-2 years, the battery may need to be replaced. Below we will tell you how to understand when it is time to contact the service center.

Quite rarely, a battery immediately swells to its maximum size, the process takes place gradually. In the case of plastic iPhones, you can observe how the body of the smartphone changes shape, becoming more convex. Cracks may also appear on the case. In the case of more modern glass and aluminum iPhones, a slight bulging of the screen can be observed. If your screen sticks out a little, creaks, and when you click on it, stains appear on the display, you should contact the service center. The screen may bulge and creak after being dropped, and not necessarily due to the battery. However, if the battery continues to swell, it is dangerous for you and your smartphone. In the worst case, a swollen battery can destroy the smartphone display, which is significantly more expensive to repair.

Manifestations in work

Software tracking

Read also

Did you know that your iPhone always knows where you are? No, we’re not talking about geolocation in applications right now. Many iPhone and iPad users are unaware of the fact that their devices are constantly sending data about their location to Apple, and also save all the information on the devices themselves. It’s one thing if a person has nothing to hide at all, []

Despite the fact that Apple has been very active in developing Mac computers in recent years, offering super-cool updates almost every year, their front cameras seemed to be stuck in the late 2000s. 720p for top models and 480p for basic ones like the MacBook 12” clearly did not contribute to obtaining a high-quality picture. It is clear that there is no point in using []

While the subscription-based app distribution model is no longer new or surprising, most users have learned to take it for granted relatively recently. After all, even some five years ago, the need to pay for access to an application on an ongoing basis seemed to many to be a separate kind of robbery, given that the average user can have several dozen programs. But with time []

Battery Check Using iBackupBot Windows Program

If you want more information on the wear and tear of your iPhone’s battery, then you can use desktop software. There is a program for the Windows operating system called iBackupBot. It is paid and costs 35 dollars, but during the first 7 days you can use it for free.

In order to check the level of battery wear using iBackupBot, launch it on your computer and connect the iPhone using a cable. After that, you need to wait a little while the program detects the device and creates its profile. When the device is detected, pay attention to the left side of the window and select your iPhone here.

Then open the Information section.

As a result, you will see information about the level of wear on the battery of your iPhone. There will be many parameters, the most important of which we will consider separately.

• Cyclecount the number of times the battery is charged and discharged;
• Designcapacity initial battery capacity;
• Fullchargecapacity current battery capacity;

The number of charging and discharging cycles of the battery is another very important parameter that indicates battery wear. The more cycles the battery has passed, the worse its condition. If your battery has more than 500 cycles, then it’s time to think about replacing it.

Checking Battery Wear Using iOS Apps

For example, you can use the Battery Life app. After launching this application, you will see the percentage of wear on your battery, as rated by the application. In the screenshot below, that’s 87 percent.

If you wish, you can see more detailed information about the battery of your iPhone. To do this, click on the button in the upper left corner of the screen and go to the Raw Data section.

Here you will see two options: Capacity and Battery Charge. The Battery Charge setting is just the current charge level of your iPhone, it’s not interesting. But the Capacity parameter is more interesting. It shows the current capacity of your battery (in the screenshot it is 2400 mAh) and the initial capacity of your battery (in the screenshot it is 2750 mAh).

It is the difference between these values ​​that is calculated as a percentage. The greater the difference between current and original capacity, the worse the battery condition.

How to check battery wear level on iPhone

You can use iPhone settings to find out the battery life and which apps drain your device’s battery the most. But, in the settings there is no information about the state of the iPhone battery and what level of wear it has.

Fortunately, this information can be obtained using third-party applications and programs. In this post, we are going to show you how to check battery wear on iPhone using iOS apps and programs for Windows and macOS. Information will be relevant for all iPhone models, iPhone including 4, 4s, 5, 5s, se, 6, 6s, 7, 8 and iPhone X.

Checking the battery using macOS CoconutBattery

If you have a macOS computer, you can check battery wear using the CoconutBattery program. The main purpose of this program is to view information about the MacBook battery, but it can also provide information about connected iOS devices (iPhone, iPad, etc.).

In order to use this method of checking the battery, simply connect the iPhone to your computer, run the CoconutBattery program and go to the iOS Device section.

As a result, you will see a screen with information about the iPhone battery. This will show the current battery level (Current Charge), maximum battery capacity (Full Charge Capacity), initial battery capacity (Design capacity), the number of battery charging cycles (Cycle Count), and other parameters.

As you can see, the amount of information here is almost the same as in the iBackupBot program.

We disassemble for iPhone 5 / 5S repair

After several years of using an apple smartphone, people are starting to wonder: how to disassemble the iPhone 5? Someone will ask: why is this necessary? There are many reasons why iPhone fans do this. They can be listed almost indefinitely, but we will describe only three of them, because somehow you are not here for this.

The first reason is to give your device a unique fresh look. The fact is that over time, the back panel on your iPhone can get pretty worn out. And if you have a black version of the iPhone 5, then paint problems will definitely make you do it.

The second reason is a scratched protective glass, which prevents the sensor from working properly. The third reason is hardware problems. Poor battery condition, faulty Home and Power keys, or a broken screen.

A set of professional tools

All these problems make us think whether to carry the iPhone to a service center or disassemble the device ourselves. A trip to the service center can hit your wallet. After all, you have to pay for the materials and work of the master. Disassembling yourself is not as difficult as it seems, and besides, you can save a lot on this. In this article, you will learn how to disassemble iPhone 5 and iPhone 5s by yourself.

First, turn off the device. You start the same way as in the case of the iPhone 4 / 4s: unscrew the 2 screws at the bottom of the iPhone 5. For the iPhone 5s, the disassembly procedure begins in the same way.

We take the suction cup and, with its help, raise the screen. Further, we move aside the structure with the screen, but not completely. Only the part where the Home button is located. For the iPhone 5s, you will need to disconnect the ribbon cables that lead to the motherboard from the Touch ID sensor. The top remains connected to the rest of the smartphone with a small ribbon cable.

Putting the screen unit vertically, unscrew the screw that holds the cable mount. Disconnect the cable with a plastic spatula. The screen unit is now detached from the case. If there were malfunctions with the Home button or the reason for the disassembly was a faulty speaker, screen sensor, broken glass, then we continue to disassemble the screen unit.

To replace the speaker, you will need to unscrew 2 screws and disconnect the contacts from the screen block. The speaker is now ready to be replaced. Remove the Home button from the bracket, and replace it if it was faulty. In order to replace the glass or screen, unscrew the screw on the metal base. After that, nothing prevents you from replacing the screen or broken glass.

In order to replace the Home button in the iPhone 5s, aka Touch ID, you need to pry it with a rubber spatula and carefully remove it.

If the problem was in the battery, the board, or you want to change the color of the case, then we continue the process of disassembling the iPhone 5. To replace the battery, you need to disconnect the ribbon cable from the board with a plastic spatula. Next, use the same spatula to pry on the battery and pull on the plastic tab (on iPhone 5s, Apple abandoned this tab). We remove the battery and replace it.

The battery in the iPhone 5s can be dismantled as soon as the Touch ID cable and the cable connecting the battery to the motherboard were disconnected without completely removing the screen unit.

Next, we proceed to dismantle the motherboard. At the same time, there is no significant difference between the iPhone 5 and iPhone 5s. To do this, you need to disconnect the antenna connector module from the motherboard, which is located below. The next step is to unscrew the screw that secures the board to the case. After that, at the top of the smartphone, we find the screws that attach the contacts to the inner wall of the iPhone 5. Unscrew them. The motherboard is completely free and can be removed.

If necessary, you can detach the camera by unscrewing the 2 screws. If it was damaged or defective, repair or replace.

Next, we continue to dismantle the bottom module, which includes the headphone jack, earpiece speaker, bottom microphone, Wi-Fi antenna and Lightning connector. This is not difficult to do, but it will take some effort, since the whole structure is fixed with glue. You can also unplug the Lightning connector if there is any problem and have it replaced.

And now you have completely disassembled iPhone 5. If you need to replace the old case with a new one, only of a different color, or change some faulty parts, now it is quite easy to do it. For better smartphone performance, we recommend that you clean everything with a brush from accumulated dirt and dust. This is especially true for small gaps between keys or holes in the bottom of the device.