Heated Kp Iphone 6s

Unfortunately, even with such a high-tech and reliable device as the iPhone 6 Plus, an unpleasant situation can happen.

Violation of operating conditions, an absurd accident, and sometimes factory defects, can cause a smartphone to fail. One of the common problems is the situation when the device does not respond to pressing the “Power” key.

Sooner or later, most iPhone users face this issue. The problem with the inability to turn on the iPhone is quite common. Each generation of iPhones has its own characteristics of this problem. The first thing to do is connect the iPhone 6 to the original charge.

Heated Kp Iphone 6s

often than not, the “Power” button itself is the culprit of the breakdown, in which the contact pad or cable is damaged. The reason most often lies in the ingress of moisture into the body or in mechanical damage to the part caused by the fall of the phone. Also, a smartphone’s often failure to turn on is caused by a serious software malfunction or a power system controller failure.

Why and how to solve

The reasons why the iPhone 6 turned off and does not turn on are many.

The enlarged ones can be divided into the following:

  • full discharge of the device;
  • software issues;
  • hardware problems.

Software problems are easier to solve; in a situation with hardware problems, the solution is more complex and expensive.

Software crash

The most common reason an iPhone doesn’t start is a software crash. To fix a software malfunction, it is necessary to hard reset the device. To do this, simultaneously press and hold the power key and the Home key for 15 seconds. As a result, the device will reboot and will be available for normal operation.

If this does not help, then you should try to put the device in recovery mode. To do this, hold down the “Power” and “Home” buttons for 30 seconds.

In a situation where such an elementary solution to the problem together with thorough charging of the battery did not solve the problem, the reason for the inoperative device may be as follows:

  • the gadget battery is faulty (replacement for a new one is necessary);
  • the adapter or the USB cable is damaged (an adapter or USB cable is needed);
  • the cable connection connector is dirty (it is necessary to clean the cable connection connector);
  • low-quality (cheap) cable (replace with original);
  • mechanical damage to the connector and other mechanical damage, for example, due to falling, moisture, after charging in a car, etc. (you must contact the service center);
  • marriage (you must contact the place of purchase).

It is also possible that the iPhone may not turn on after updating the firmware.

There are three different scenarios, depending on when the crash occurred during the firmware update:

  • flashing the phone again;
  • Replace the defective NAND Flash. This is a memory chip on which all the personal data of the owner is stored;
  • Replace a failed Nor Flash. This is a GSM module memory chip. All parameters of mobile operators are stored there. Without these parameters, the device will not be able to call.

Power and Charging Issue

If you cannot turn on the iPhone 6, then, most likely, the problem is in power or charging. First of all, you should try to charge it. over, you need to connect it to the charger for at least 20 minutes from the adapter and 30 minutes from the workstation.

After that, you need to try to start the iPhone without disconnecting from charging. If everything is normal, the lightning symbol will appear on the display inside the discharged battery.

When the battery of Apple’s smartphone is discharged to zero, then after a short charge, when you press the power button, the picture on the display shows a socket with a lightning symbol.

The way out of this situation is to charge the device longer. In this case, the charging time should be at least 3 hours.

There are situations when the connector through which the phone is charging fails when using non-original charging.

It is very important to know how seamlessly you can charge your iPhone 6 in a car, and more importantly, follow these basic rules. This leads to grave consequences. In the best case, you need to replace the battery on the iPhone. At worst, it is replacing a power controller or repairing a failed power circuit.

How to create email on Yandex for free? The answer is here.

iPhone 6 could

In addition to problems with the battery, not turning on the iPhone can be explained by the human factor. This is especially common when the phone is worn in a trouser pocket.

The device’s connector is clogged with dust and dirt, and the next time you try to charge it, the iPhone simply breaks. This problem is not very serious, since any service center can eliminate it in a few minutes for little money.

Pour liquid

Moisture on the phone or even flooding it with liquid is not uncommon. Problems with the iPhone can begin not only when drowning it in the pond, but even when it gets in light rain. In this situation, the gadget may start to fail.

In this case, cleaning the device or component repair of the motherboard is highly desirable. At the same time, it is important to stop using the phone immediately if moisture gets inside the device.

The solution to the problem is not entirely trivial, therefore it is recommended to seek help from a certified service center and avoid problems that may arise in the future.

Miss on the floor

The problem with turning on the iPhone may be due to mechanical damage, namely falling to the floor. It is important to remember whether there was a fall a certain time ago, since the peculiarity of this situation is that problems with the smartphone can begin to appear after a fairly long time after the fall.

The impeccable appearance (without scratches and other visible flaws) does not mean that there are no problems with it.

As an option, one of several loops can snap off:

  • power cable
  • display loop;
  • battery cable

A more serious situation is related to a violation of soldering on the motherboard or damage to one or more microcircuits.

IPhone users may experience a situation when the device turns off and does not turn on. If you do not consider the simplest options, when the battery was simply not charged in time, then most likely the problem is in the malfunctions of the gadget’s operating system boot data block.

This problem can be solved if you try to restore the partition by connecting the smartphone in DFU mode.

How to compress the Internet cable? The instruction is here.

How to make your presentation on a computer? We create here.

Often, a hard reset will help to remove the device from this position, and if moisture gets inside it or mechanical damage, it is better to contact professionals.