DIY iPad stylus

Paper

Rolled paper with a tip dipped in water. can be used as a stylus.

ipad, stylus

Ballpoint pen and wire stylus

To make a stylus in the second way, we take any wire, a body from a ballpoint pen, water, a cotton swab and a plastic bag. To begin with, as in the first method, cut a cotton swab in half, wet it with plain water and squeeze it out. Cut a square from a plastic bag with sides of about 2 cm.Wrap a cotton swab tightly with a piece of cellophane and insert it into the body from a ballpoint pen.

Now we will unwind as much wire as needed. In some cases, the wire is insulated. Therefore, before winding it up, you need to remove the protective layer of varnish from it. This can be done using the usual improvised means: sandpaper, scissors, knife.

Now you need to wrap the wire around the area where your fingers will be, or the entire stylus. It depends on the length of the wire and your desire. We make the last turn of the wire around the cotton swab.

Aluminum can stylus

To make a stylus in the first way, you will need an aluminum can, water, a cotton swab, and a plastic bag. Cut the aluminum can lengthwise, cut off the lid and bottom.

Next, we unfold the can to form an aluminum strip. Be careful, the edges of this strip may be sharp. Therefore, they should be trimmed so as not to cut yourself later.

Roll up the strip to make a thin tube.

Next, cut a cotton swab in half, wet it with plain water and squeeze it out. Cut a square from a plastic bag with sides of about 2 cm.

Tightly wrap the cotton swab with a piece of cellophane and insert it inside the tube.

Comparison of stylus

We compared the work of homemade stylus with a purchased one.

The purchased stylus is not convenient, as it does not slide on the screen, the rubber tip is punctured.

It is much more convenient to draw with homemade styluses, you get the feeling that you are drawing with a pencil.

It happens that styluses do not work well. Then you just need to take out the cotton swab and rearrange it. This is due to poor contact.

Stylus from the radio antenna

To make a stylus in the third way, you will need an antenna of an old radio receiver, water, a cotton swab, a plastic bag.

If you have an old unnecessary radio or tape recorder, then the third method of making a stylus will be the most convenient and fastest for you. Unscrew the screw that holds the antenna and remove it.

Then remove the first two sections from the antenna. Next, cut a cotton swab in half, wet it with plain water and squeeze.

Cut a square from a plastic bag with sides of about 2 cm.Wrap a cotton swab tightly with a piece of cellophane and insert it into the antenna.

How to make a stylus for your phone

New generation phones do not need to be poked with a pencil or stick in order to press a symbol, it is enough to touch them with your finger. the phone will react to heat. But not all fingers allow you to accurately press the symbol he needs, but the heat shield on a wand or pencil simply will not respond. In this video you will see how you can make a thermal stylus for your phone with your own hands.

Materials for making a stylus:. an ordinary helium pen;. a pen-pen;. a piece of foil in size, like a chocolate bar;. a small piece of a sponge or washcloth;. a small piece of cellophane or cellophane bag.

We will use a helium pen for the case.

From the pen-pen, we only need an elastic band, the plastic itself can be thrown aside.

Let’s start assembling. The stylus sponge should be slightly damp, but not very wet.

If you’ve seen phone reviews before, you may have seen that a wet sponge passed over the glass left streaks on the display. So that there are no drops on the display, we need a sachet for this.

To begin with, we cut off a small piece of the bag and wrap a damp sponge in it so that there are no traces of stains on our screen. The sponge should be rolled into a tight circle.

We need to insert a sponge wrapped in a bag into an elastic band. After we have inserted the sponge, we need to push it with a regular rod to the second base. The sponge should be pushed slowly, the bag should be fully opened at this time, i.e. you will only push the sponge itself, and the bag will only envelop it.

A small ball should stick out of our gum (sponge in a bag).

Next, we need a piece of foil, it can be strengthened by folding it into a double layer. Ideally, the foil should be rolled into a small flagellum. Handle the foil with care. It must not be allowed to break. You can use not foil, but vinyl film or a paper clip.

Now we very carefully insert the foil into the elastic so that the foil touches the sponge. We should get a thin metal rod made of foil, which touches the sponge with one side, and with the other side it should envelop the walls of the handle. The part that will stick out from the elastic can be bent or cut.

Gently insert the handle itself into the gum, while the foil should go from the sponge to the side.

So we got a thermal stylus, which looks like an ordinary helium pen.

Cotton swab

The simplest but most effective method is to make a stylus from a cotton swab. In addition to the stick itself, you will need foil. Simply wrap the stick with foil and then wet the tip of the resulting stylus. Vata, soaked in water, will become a good conductor.

You can improve this stylus by making it longer. Now you will need more scissors and a pull-out handle:

  • Remove the rod from the handle.
  • Cut off one end of a cotton swab.
  • Insert it with the cut end into the handle. The cotton tip will stick out like a long rod.
  • Now wrap this whole structure in foil. Please note that you will have to hold the pen by the foil to use. do not wrap just the very tip.
  • Dip the tip of a cotton swab in water.

If desired, for convenience, you can cut off the second end of the cotton swab and insert it into the handle, wrapping the entire structure on top with foil

When using this stylus, always touch the foil with your fingers. Moisten the tip periodically in water again if the touch response becomes unstable. This stylus is the most convenient to use, and the smartphone will react to it quite sensitively.

To adjust it for painting, squeeze the tip with your fingers to seal the cotton with foil. Repeat this periodically. over time, the cotton wool will again “blur” and become too soft for drawing.

Sponge

A common dishwashing sponge can serve as a guide. You will need:

  • new sponge;
  • a handle with a removable shaft and a removable tip;
  • scissors;
  • tweezers (optional).

This simple stylus is made like this:

    Tear off the hard side of the sponge (if any).

A hard surface can scratch the screen, which we don’t want

The stylus tip will look like a pencil eraser

The resulting stylus is far from ideal, but it still works. Its main disadvantage is low accuracy due to the soft and large tip.

We get a stylus like an expensive phone without spending a penny

Multifunctional styluses aren’t cheap. But in fact, these are not such complex devices (for the most part). Today we will make quite simple, but working styluses from scrap materials.

Types of touch screens

Before you start making a stylus, you need to know what type of screen your smartphone has: resistive or capacitive.

The resistive screen responds to the touch of any object. Its principle of operation is based on a thin and flexible membrane that sits on top of the display. When we click on it, it connects to the main part of the display. We will not go into technical details. we are interested in the fact that the resistive screen responds to pressing with any object. This means that the resistive display stylus can have a tip of any solid material.

Resistive displays are now almost never used for smartphones and tablets. They have found application in e-books, projectors, PDAs. This is largely due to the fact that they do not tolerate low temperatures poorly. it is better not to go out into the cold with such a device.

The capacitive display only responds to touching conductive objects. Our finger is just that. The principle of operation of a capacitive display is also quite simple. A weak alternating current is supplied to the display. Current leakage occurs when the display is touched by an object with conductive properties. The sensors record this and instantly calculate the coordinates of the touch. The stylus for such a screen must have an electrically conductive tip.

How do you determine the type of display? Very simple. take the pen cap and slide it across the screen. Reacts? So the display is resistive. Zero reaction? Capacitive.

Making a stylus with your own hands

Now let’s try to make a stylus from scrap materials.

Capacitive display

For a capacitive display, we will definitely need a conductive material.

Making a stylus. the way

The first method is the fastest and simplest, but the present invention will be disposable. The fact is that the salt water used in its construction will dry out quickly. Such an accessory will be quite enough for several hours, but after that it will need to be moistened in water.

To create such a device, you will need:

  • Empty pen
  • Insulating tape
  • Scissors / threads
  • Sanitary stick / cotton wool
  • Foil
  • Salt
  • Water

This method is clearly shown in this

First, roll the foil into a tube and place the handle in the empty cavity so that the foil takes up all the space in it, sticking out a little. Then wrap the protruding piece of foil with a veil, securing it with thread, or insert half of the sanitary stick into the handle so that the soft tip sticks out.

Then, wrap foil over the entire handle and secure the material with duct tape. All parts of the accessory must be in close contact with each other.

In order for the device to work, you need to place the tip of the homemade stylus in salt water for a few seconds. We need salt water to conduct energy. Your stylus is now ready!

What is a stylus for??

A stylus is a small, bunched or pen-shaped writing wand that can be controlled by a computer graphics tablet or touch-sensitive devices. Today, a huge variety of these accessories are made, but you can make a stylus for the iPad with your own hands.

  • The accessory is very convenient when writing on the screen, because it is not very convenient to display symbols with your fingers
  • To work with graphic editors, tables or diagrams, the stylus is simply necessary, since small elements require high precision. This is why the stylus is the best tool for designers and artists.
  • Using a stylus will make your screen less dirty
  • If you think about hygiene, the stylus is much less likely to carry bacteria than dozens of hands touching the screen.
  • Game lovers will find it much more convenient to use a stylus rather than fingers
  • And, of course, for girls who wear long nails that prevent their fingertips from touching the screen, a stylus is the best solution.

Homemade stylus for iPad

By inventing the legendary iPhone, released back in 2007, Steve Job made a real revolution. controlling the phone became possible with your fingers! But why not use your usual stylus? The answer is simple: you take it out, then you take it away, then you take it out again, and, in the end, you lose it. Nevertheless, for some programs, primarily for drawing, this accessory is required. In this regard, we will consider the question of how to make a stylus for the iPad with your own hands and from handy materials.

Making a stylus. the way

The second method will help you create a more durable stylus.

How to make a DIY Touch Pen in 2 Minutes. AWESOME

To invent it, you will need:

  • A pen
  • Pliers
  • Protected wire
  • A piece of polyethylene foam

First, remove the rod and all other parts from the handle, leaving only the tube. Cut a piece of polyethylene foam so that it can fit in the handle, but still grip tightly. Cut a piece of shielded wire so long that it is 2-2.5 times longer than the handle. Free the part of the wire that extends beyond the length of the handle from the protective rubber (in simple words “strip” the wire).

Wrap the bare wire around half a piece of polyethylene foam. Insert the structure into the handle so that the free part of the polyethylene foam sticks out of the handle by a centimeter.

Now, in your stylus, one side of the pen is covered with polyethylene foam, and the other end of the wire sticks out from the other. Separate the protective rubber from the protruding end and coil the wire around the handle. Secure it with duct tape. Now smooth the end of your stylus a little, and it’s ready.!

How To Make A Stylus Using Any Pen/Pencil

If you like, you can make the stylus tip of any size. Thus, you will have the perfect tool for controlling iPad, and especially for drawing.

Our service offers the purchase of computer, digital and video equipment from Apple on the most favorable terms

Get professional advice from a licensed Apple technician now

All rights reserved, for any copying of the material, a link to the site ¶¶¶ is required. Aggle Service Center is a post-warranty (unauthorized) service center. The information presented on the site is not a public offer.

  • iPhone
  • iPad
  • MacBook
  • iMac
  • Watch

Moscow, avenue Vernadsky, 39, office 425 in the business center “Vernadsky”

Apple products, trademarks and registered marks are the property of Apple Inc.

DIY iPad stylus

Doing something with your own hands has always been highly appreciated.

Especially when it comes to modern devices and accessories for them. Probably every happy owner of an iPad at least once tried to adapt some thing as a stand for his tablet.

With the release of numerous drawing and design programs on the iPad, there is an urgent need for a stylus. If for some reason it doesn’t suit you, you don’t like it, or you simply cannot purchase a ready-made stylus. Try DIY iPad stylus. There are several ways to make your own iPad stylus. This article describes two of them. 1 way how to make a stylus for iPad with your own hands: A very simple way. However, the stylus obtained in this way will be disposable. It will be enough for just a few hours. Then you will need to moisten. To create a stylus, you will need:. an empty ballpoint pen. scissors. electrical tape (you can use threads). a hygienic stick (a small piece of rag). foil. water. salt First you need to twist the foil with a tube and insert it into an empty pen so that it fills everything in the pen space and looked out a little. Next, wrap the foil with a piece of rag or cut the stick into 2 parts and insert into the foil. In this case, the cotton head should be in contact with the foil. After that, wrap the handle itself tightly with foil. All elements must be in close contact with each other. For beauty, you can wrap the pen with duct tape or thread. Those who are fond of knitting will be able to make an original case for their stylus.

Your stylus only needs water to work. Dip the handpiece in salted water before use. This is necessary for conductivity. After that, your stylus is ready! 2 Method of making a stylus for iPad yourself: This method will help you make a stronger and more durable stylus. To do this, you will need:. an empty ballpoint pen. pliers. shielded wire. polyethylene foam (used as a lining for radio components). The first step is to cut the polyethylene foam so that the desired part is about the thickness of a ballpoint pen. Next, you need to peel off the insulation from the tip of the wire, stick it into the polyethylene foam and twist it around it. Then carefully thread the wire through the handle. Leave the tip with the polyethylene foam a few millimeters out.

Bare the rest of the wire and wrap it around the outside of the handle. Glue the tip with electrical tape. For beauty and convenience, at the end, you need to trim the protruding end of the polyethylene foam, making it round. Check it out. you get a great stylus!

A stylus for a capacitive screen: why is it and how to make it

Nowadays, capacitive touch screens are replacing resistive screens more and more actively. This type has obvious advantages: this type of sensor is more robust and durable due to the fact that the flexible resistive membrane in it is replaced by a grid of electrodes. The capacitive screen supports more touches than its sibling, it is more transparent, and only for it the multitouch technology is now implemented, which is popular today.

The difficulty lies in the fact that using your fingers to work with the interface is not always convenient, and in this case there are no other options. This is quite noticeable when drawing or entering handwritten text on the tablet screen, as well as in winter, when you don’t want to take off your gloves on the street, but certain manipulations need to be made. At such moments, a stylus for a capacitive screen would be useful to many. Many may remember the convenience of using such a manipulator if they once owned smartphones with resistive screens. It allows for more precise manipulations. But the capacitive screen does not respond to the touch of an ordinary stylus, since it requires a certain capacitance to work with it, which accepts and conducts an electric current with a low voltage. Mobile phone manufacturers are also ready to offer a stylus for a capacitive screen. It can be different in appearance, but it is made from special conductive materials. The stylus for a capacitive screen has a fairly simple device that allows you to make it yourself.

The mobile gadgets market offers four types of stylus models:

The stylus model SPMP 1019, designed for iPhone, iPad, HTC and Samsung screens, belongs to the second category. This model is considered inexpensive, and high quality is ensured through the use of a metal case. The presence of a hook, similar to that on a ballpoint pen, allows you to conveniently fix it. Its disadvantage is fragility. This gadget will not lose its tactile properties at low temperatures. At the moment, the most convenient stylus for a capacitive screen is made of conductive rubber. It has design features that provide a seamless touch of the screen with your fingers. The tactile response of such devices is considered to be the highest. The degree of depression is easily adjustable.

DIY capacitive screen stylus

From what was written earlier, it should be clear to you that the market is ready to provide a huge variety of options for this device. However, the question of how to make a stylus for a capacitive screen can be of concern to many. Here you can recommend the following set of tools: embossed pushpin, nail file, metal pen, tin, soldering iron, glue, copper wire, self-adhesive, battery. The wire should be soldered to the button, after which the workpiece should be pushed into the handle body, and glued at the end. Stick the self-adhesive on the button, and cut off the remains. The other end of the wire should be fixed to the battery, close the handle body. Capacitive stylus ready!

Stylus from cable

The third option for an impromptu stylus can be a cut of a coaxial television cable, about 10 cm long.From the working end of such a stylus, bend or cut off the central core in order not to damage the screen of the device, and the stripped braid should be wrapped around the external insulation, so that reliable screen contact.

Despite its simplicity, this design option turned out to be the best of all homemade styluses.

STYLUS FOR A CAPACITIVE SCREEN WITH YOUR HANDS

At the moment (2017), the most common touch control technology is capacitive screens, which respond to touching the working surface with a conductive object. Most modern tablets and smartphones use this technology. details about this technology can be found at the following links.

  • http://www.xtechx.ru/c40-visokotehnologichni-spravochnik-hitech-book/capacitive-touch-screen/
  • http://tehnoobzor.com/tests-reviews/to-laptops/141-sensornye-ekrany.html

First of all, such a screen is focused on using your fingers, but in some cases it is desirable to have a separate stylus for working with a capacitive screen. For example, if you often have to touch the screen with dirty hands. It is quite simple to make such a stylus, almost any conductive object will do, the main thing is that it does not damage the surface of the screen and gives a reliable response. There are a lot of descriptions of such structures on the Internet, for example, such a construction. But it requires regular wetting of the stylus, which is not convenient, and in general, the increase in humidity does not benefit any electronic device.

Homemade styluses

The rather unusual design of the capacitive stylus is a ring of conductive material, about 1 cm in diameter, attached to a pen made of the same material. Such a construction is described here. It seemed to the author that such a stylus could be made much easier by folding a suitable piece of single-core wire in the required shape.

The part of the wire that the user holds with his fingers is stripped of insulation. In general, the design is efficient, although sometimes the screen misses the operation.

The idea arose to further simplify the construction of a homemade “stylus” simply to strip one end of the wire by 4-5 cm, and roll the other insulated end, about the same length, into a spiral. But this design turned out to be not very efficient, the screen regularly skips commands.

Stylus from antenna

Some resources advise to make a homemade stylus from a segment of a telescopic antenna, putting a roll of food foil into the working end of such a stylus, the working end is wrapped from above with the same foil so as not to damage the screen.

In general, such a design is efficient, but it requires strong pressure on the screen, I think this option is not suitable for long-term use.

And of course, the best result was shown by the factory-made stylus, purchased here at Aliexpress.

In transport condition, the stylus length is 125 mm.

The working element is covered with a screw cap.

In working position, the cap can be screwed onto the back of the stylus, while the total stylus length is 140 mm.

Stylus working element close up

The weight of the device is 20 g. The stylus works reliably, with its help it is easier to perform small manipulations on the tablet screen than with your fingers. Article author. Denev.

Why “stylus”?

Where did this word come from? “stylus”? It has Greek roots and originally meant a small stick that has a pointed end. It is these small “sticks” that today help users of high-tech devices to manage. In addition, with their help it is very convenient to draw drawings on a graphics tablet.

Curiously, some time ago, experts predicted the end of the era of stylus. However, one can observe a picture where the presence of a stylus is still required in the work of the latest devices. This is especially true of high-tech brainchilds of Samsung: stylus for Samsung tablets are in demand.

With the history sorted out. Let’s continue. It was noticed that a large number of users complain about the fragility: they say, the stylus for the tablet quickly deteriorates. It is also noted that they are simply easy to lose. Special programs came to the rescue: some of them notify the owner that the stylus is at a remote distance from the device, such as a tablet.

For graphics

The Bamboo stylus is a good choice for drawing graphics. This pen tablet stylus allows you to sketch lightly and has a proven track record. Yes, it is not without its drawbacks: for example, its tip is made of rubber. This means you have to push harder on the screen, and the tip itself tends to slide over the surface at times.

If there are no budget constraints, then you can choose the Pogo Connect model, which has as many as 4 tips in its arsenal. It was noticed, however, that with new devices Apple does not work very correctly.

How to choose a stylus for your tablet?

Are you a happy owner of a tablet and want to choose a convenient stylus? This is a laudable desire, because a properly selected device can greatly facilitate the work with the device. So how to make a choice?

You should know some facts about the operation of this small accessory. For example, styluses can vary in pressure. Rather, by sensitivity to this very force. In addition, styluses vary in weight, which can also play a significant role in its handling. You should choose one that is comfortable for you to hold in your hand! Note also the tip: size and shape can have an impact on performance. If the owner of the device does not want to use the virtual keyboard, then choose a stylus for the tablet that is able to work as quickly as possible, and the accuracy of which is very high.

A stylus for a tablet: how necessary an accessory?

A large number of users of modern high-tech devices decide to abandon the keyboard and mouse. Such trends have given rise to the emergence of touch screens that are able to respond to finger touch, or a special convenient accessory called a stylus. A stylus for a tablet is a kind of thin pen that allows you to control a device equipped with a touch interface. This includes tablets as well as tablet computers. The stylus can be observed in the hand of the user of a PDA, smartphones.

DIY stylus for tablet

Among the users of high-tech devices, there will certainly be those who like to craft with their own hands. It is to these people that the next part of the article is devoted. how to make a stylus for a tablet with your own hands.

However, this shape is not well suited for a capacitive screen. Users concluded that such a screen is oriented towards contact with an object that has a larger contact area than a pencil shaft. How could this problem be solved?

A way out was found: the annular shape is well perceived by the sensor. In addition, you can easily view the center, see where you point the stylus.

Summing up all the conclusions, you can make such a stylus: take an aluminum rod (conductor), a steel washer and a skein of thread.

The pen must be soldered to the washer at an angle convenient for the future stylus. You ask: “Why did you need a skein of thread?” In order not to scratch the screen. As noted, the annular edge allows you to aim through the center. And wind the threads on it. not a problem.

Someone may argue, they say, the threads worsen the level of sensitivity. In practice, everything works out very well, because the sensor does not need absolute contact with the object to determine the touch. It was noticed that even by pressing with a finger, it was possible not to touch the screen closely.

Do-it-yourself capacitive stylus assembly

  • ballpoint pen;
  • aluminum foil;
  • cotton swab;
  • scotch tape;
  • scissors.

The assembly of a capacitive stylus looks like this:

  • Remove the refill from the ballpoint pen.
  • Cut off half of the cotton swab at a sharp angle. Insert it into the place of the rod in the handle with the cotton head outward.
  • Fix the cotton swab in the handle with tape.
  • Take a piece of foil and wrap it tightly around the handle, stepping back 1 cm from the cotton head.
  • Secure the foil wrapper with a piece of tape. DIY stylus is ready!

To use this device, you need to have a glass of water on hand. for optimal performance, the fleece will have to be moistened from time to time. The capacitive screen does not deteriorate from the moisture of the stylus. Also remember to keep your fingers on the foil at all times. this is necessary in order for static electricity to act on the display.

Resistive, capacitive and heat shield

If you are eager to make your own stylus, then first of all find out the type of touch screen of your device. this will directly affect the materials for your craft:

  • Resistive screen. This type reacts to absolutely any touch. finger, sushi stick, pencil, etc. Choose what you like best and your stylus is ready!
  • Capacitive screen. This touchscreen only reacts to the touch of conductive objects. Man, too, to some extent relates to them. our fingers, like ourselves, conduct electricity. This quality is possessed by all organic substances and creatures, as well as most metals.
  • Heat shield. As the name implies, the display will only respond to the touch of an object that emits heat. That is why it is difficult for us to work with such screens in the conditions of Russian frosts.

DIY stylus for thermal and capacitive screen

The market of modern gadgets decided to remind us again of the already forgotten stylus. Branded “sticks” were recently presented by Apple; Samsung is releasing a line of S Pen styluses for its Galaxy Note product. Such a device is also convenient for those who like to draw on the screen of their smartphone or tablet. It is quite possible to make a stylus with your own hands quickly and without the use of expensive materials.

Additional ways

You can make a stylus for a capacitive screen with your own hands in a slightly different way. For example:

  • Take an aluminum tube, attach a piece of anti-static sponge to one of its ends, which can be found in chip boxes.
  • You can build a stylus with your own hands from the same pen without a rod, replacing the cotton wool with paper, and foil. for metal packaging made of chocolate, coffee, tea, etc.
  • Some users prefer to use a thin battery as a stylus, bringing its negative pole to the screen.
  • You can use one anti-static film rolled into a tube, securing its shape with pieces of scotch tape.
  • Lightweight, non-scratching aluminum stick. also a good stylus. Only its head should not be too small, otherwise the screen simply will not “see” this object.

DIY thermal stylus assembly

  • feather pen;
  • gel pen with rubber band for fingers;
  • a piece of foil;
  • a piece of a dish sponge or washcloth;
  • a piece of cellophane.
  • Leave the body only from the helium pen, and from the pen. gum.
  • Dampen the sponge with water.
  • To avoid streaking on the screen, wrap the sponge in cellophane.
  • Now insert the cellophane-covered sponge into the handle. You can push it with the same helium rod, slowly. so as not to harm the bundle. As a result, only a sponge ball wrapped in a bag should be visible from the handle.
  • Remove the finger elastic from the handle.
  • Having folded a sheet of foil twice, twist a thin flagellum out of it.
  • Place this foil rod so that one end touches the sponge and the other wraps around the body of the pen.
  • Make several turns of the flagellum, put the elastic in place. The part of the foil that will stick out over the elastic can be cut off. Stylus made!

As you can see, make a stylus with your own hands. a pretty “cheap and angry” easy way, either for a thermal or for a capacitive screen. For a resistive display, any convenient handy item can be used as a stylus.

DIY stylus

Hello to all homemade products. Today I will show and tell you how I made a stylus for a smartphone. This homemade product will be useful for artists, designers, etc. If there is no factory option, this DIY will be a great solution. There are many such homemade products on the Internet, but they are not completed yet. Some use wet cotton wool, others use foil, etc., but they have the same principle of operation. You need to use a conductor that is in contact with your hand. The body’s electricity is transmitted through the conductor and the conductor, in contact with the screen, produces pressing, movement, etc. But they work weakly or work every other time on a smartphone. And on the tablet in general, zero reaction.

To make this homemade product, we need

Foil 2. Handle 3. Lighter with a flashlight. Namely, you need batteries, but you can use AA batteries. 4. Scotch tape, electrical tape

We connect foil and batteries

Unscrew the screw and carefully remove the batteries from the lighter body. Now we cut the foil into two parts and fold both parts into a thin strip. We glue one strip with tape to the minus of the battery. We wrap another strip around the contact and insert the contact to the plus. We wrap batteries and strips with tape.

We insert everything into the handle body. We wrap a little cotton on a cotton swab. Then we wrap the foil on it. We connect the strips with foil and insert the cotton swab into the body and fix it with a piece of tape.

How to choose the right stylus?

Styluses differ in size. And also what surface they are intended for. What to choose? When choosing, be sure to take into account not only the screen size, but its technology, as well as the size of objects on the screen, which will need to be pressed with the stylus.

Universal styluses are suitable for many touch screens. However, there is a reason, when choosing a stylus, to take into account the specific characteristics of your gadget. Do not be lazy to read the recommendations for your device. it has a resistive screen or a capacitive one.

For example, for the iPhone, as a rule, they purchase stylus in the form of a pen. The tip of these stylus pens is thick because it mimics the touch of a finger. For Nokia phones, they buy stylus in the form of mediators or flash drives. A stylus with a regular thin tip will fit many touchscreen devices.

What are capacitive screens

How do they work? The display is covered with a thin conductive layer. And when any material that conducts current touches it, the resistance changes in the display area. It becomes a signal that a click has occurred.

In many mobile touch-screen devices, resistive technology is already very outdated. over, it is outdated so much that capacitive touch screens have partially replaced them.

I must admit that the capacitive sensor is stronger. And therefore it lasts longer. This can be explained by the fact that it uses a grid of electrodes. And it is applied to almost any surface. If you take a flexible resistive membrane, then it can be very easily damaged.

To put it simply, such touchscreen displays are responsive, you just have to touch your finger. Note at the same time that this touch does not have to be strong at all. We also emphasize that a capacitive screen at one point will be able to withstand a lot more clicks. It is also more transparent.

At the same time, we recall that for capacitive sensors such a function as multi-touch can be implemented, which is necessary for many.

The advantage of such displays is convenience and reliability. This is because any foreign objects that do not conduct current will not be able to accidentally turn on the device. The disadvantage is that the screen does not respond when fingers are in gloves or they are covered with liquid, dirt.

IMPORTANT! Nowadays, more and more often on sale there is a capacitive stylus, with which you can control the touch screen of this technology. Mostly it is needed by artists who have a desire to draw on tablets that have a capacitive display.

Today, mobile accessory companies are releasing special styluses for capacitive displays. And a variety of models. Various materials are used for their manufacture. The mobile accessories market is dominated by four types of capacitive stylus:

Standard stylus device

A capacitive stylus has a tip made of a material that conducts current in the same way as a human finger. It changes the resistance in a given area of ​​the monitor.

An active, or digital, stylus uses a digital converter that is built into the screen. It provides communication between the touch screen and the stylus. The active stylus is capable of supporting most of the functions, and even all the functions that a mouse performs. Specifically, right-clicking, hovering, etc.

The lion’s share of active stylus models is such that it can block hand touches if they are accidental, as well as the touch of the hand that lies on the screen, and palm movements when you write. The screen will react only when you touch the stylus.

The passive, or capacitive, stylus acts like a finger. The passive stylus does not require a battery. Passive styluses work on any device that has a touchscreen.

Active and passive styluses are slightly different.

IMPORTANT! The passive stylus can be used on any touchscreen. And on devices that support active styluses. You can find out if the device supports an active stylus by reading the instruction manual for the gadget.

Styluses for different types of touch screens

What is a stylus? What can it be? What is their scope in our time?

How to Make an iPad Stylus Pen Easy Tutorial | Toy Caboodle

A stylus is a small stick made of metal or plastic with a special tip, silicone or capacitive. Stylus can be used to select menu items, draw, write notes, sign documents, and much more.

In short, a stylus is required in order to operate touch screens. Isn’t it possible to control your fingers, that is, as usual for many? We assure you that not always. Sometimes using your fingers to tap small characters and icons is not as comfortable as using a stylus. In addition, the accuracy of each press is always much higher. And the speed of work too.

They are not very common at this time. However, there were times when the happy owners of newfangled smartphones with stylus could be seen quite often. Note that the styluses were often lost. Yes, they broke down often. Resourceful users then used fingers, matches or toothpicks.

Now the times have come when you rarely come across devices that would immediately be supplied with stylus. And the point is not that the interface elements have become larger. Also, it’s not that we’re used to tapping on the display with our fingers. Touchscreen technology has changed over the years.

IMPORTANT! Depending on the type of screen, stylus can be resistive or capacitive. Resistive styluses mimic finger presses or touches. Capacitive styluses apply the difference in magneto-electric fields between the screen and the electronic stuffing of the stylus.

What are resistive screens

Micro-insulators are located between the monitor and the flexible plastic outer panel. When you touch at a given point, a closure occurs. Its signal was processed by a special device. It, depending on where it was pressed, was converted to display coordinates.

It is for them that a stylus is needed for the screen. After all, he reacts to hard pressing. And it lacks a simple finger touch.

Despite this, they could even be used without stylus. When you lose the stylus, or it breaks, you can still press the screen. For this purpose, it is quite suitable, for example, pressing with a fingernail or some other hard object.

The advantage of such touch screens is faster typing. Note also that over the years, when the outer plastic panel becomes scratched, it can be replaced without any problems.

IMPORTANT! Similar monitors are often used in industries and in those conditions where reliability is important. In order for the sensor to be activated, you need to take an object or just press hard. Even when fingers are dirty or protected by gloves.

How to make a stylus for a capacitive touch screen with your own hands

It is better when the stylus is pointed. Like a drawing pencil with which you perform precise movements. However, this shape is not suitable for a capacitive screen. It targets contact with a larger area of ​​contact that can be compared to the touch of a finger.

But the annular shape is well perceived by the sensor. The center of the ring is visible to everything. That’s why you can see where you point the stylus and then hit it exactly. This means that in order to make a miracle wand, you will need a steel washer or any other material that conducts current, an aluminum rod, a skein of thread.

The washer is soldered to the rod at an angle that should be as compatible as possible with the natural position of the hand. There should also be full adherence of the plane of the ring to the surface of the screen. Unfortunately, this design scratches the screen. However, the problem can be solved using threads.

IMPORTANT! A ring-shaped edge is good because it allows you to wrap yourself with thread. Do not assume that an extra layer of thread will degrade the screen’s sensitivity. Indeed, in order to detect touch, the sensor does not need absolute contact. You just need to bring your finger very close. At the same time, there may not be a touch.

And now a little about the disadvantages. The principle of operation is based on the fact that the current passes through the stylus made of metal to the human body. This means that a homemade stylus will not work with gloves.

We emphasize that one manufacturer from Canada is already producing styluses of a similar design. Serial production has also been mastered. It turns out that the design is really successful.