Button not working on iPhone
Reasons Why iPhone Power Button Doesn’t Work
Thanks to the lock (power) button, your iPhone can fully function. turn on and go into standby mode, thus saving precious charging percentages. However, there are times when the iPhone’s power button starts to jam or breaks altogether. We have collected most of the most common causes of a broken power button on your iPhone, as well as helpful tips to fix this problem.
Why is the power button on iPhone faulty
There are many reasons that can cause the power button on the iPhone to stop working.
The most common reason that brings a lot of problems to every iPhone user is a simple software glitch. Identifying it is not that difficult, in rare cases it is harmless to your iPhone. However, it can scare any user if caught by surprise.
Fixing a software glitch is easy if it is a one-time occurrence and there are no problems with updating iOS. In this case, in order for the power button on the iPhone to work again, you just need to restart your smartphone.
The second most common reason your iPhone power button might not work is due to improper update or poor quality jailbreak. One way or another, not everyone knows how to properly update their devices.
Many users are very frivolous about installing updates: they do not download them to the end, interrupt the final reboot, download updates with a low percentage of charge due to poor internet. Each of the listed items can cause the installation of a “broken” update, which will bring a lot of minor and major troubles to your iPhone.
Only a master will be able to identify the wrong update and say for sure what exactly is the reason for the malfunctioning of the power button on your iPhone. But you can independently monitor the operation of your device: usually, an incorrect update does not bring any one problem, other failures should be noticed in the system that have not been observed before.
If you find them, try downloading a previous iOS backup via iCloud if you created it before. It definitely shouldn’t be worse from this procedure, and if you made the right diagnosis, the shutdown button will return to normal after the previous version of iOS is restored. Then you can try updating your iPhone again.
Sometimes the power button on the iPhone fails due to the fact that too much dirt has accumulated inside, which interferes with the operation of contacts. One way or another, we often do not notice with what hands we take our smartphone, where we leave it and quite rarely monitor the cleanliness of our iPhone.
If dirt gets into the small gaps around the button, you may notice some key jamming. But when pressed firmly, it will work. In this case, you can very carefully use a needle to clean the small connectors around the iPhone’s power button. It is very important not to overdo it, so as not to damage the contacts and not to dismantle the button.
If dirt has formed an obstacle inside the button and prevents the contacts from working properly, you are unlikely to be able to clean it yourself. You can try to drop a little alcohol on the button (one drop, no more), and then very gently press it, as if distributing the alcohol inside. However, keep in mind that doing so may cause additional harm if the power button cable components or any other part in your iPhone has been damaged.
Therefore, in order to avoid trouble, it is better to contact the service center master and ask him to diagnose your device.
If iPhone comes into contact with moisture, most of the time, it has unpleasant consequences. Yes, Apple is committed to protecting users and is providing improved water resistance for the new iPhone 11 and iPhone 11 Pro. However, the risk of breakage after moisture is still very high, so if you encounter moisture getting into your iPhone, be sure to contact the service center for a diagnosis by an experienced technician.
If, after contact with moisture, you notice the iPhone power button sticking, this may indicate damage to the loop or oxidation of the button contacts. It is very important to understand that the ingress of sugary liquids, soda, tea or coffee is doubly detrimental to iPhone components.
This problem can only be solved by fully restoring the iPhone after getting wet. This procedure can be carried out at the service center.
Dropping your iPhone is just as damaging to its components as contact with moisture. If the power button stopped working after a mechanical fall or a strong blow, it is quite possible that its loop was damaged or the contacts were broken.
Unfortunately, this problem cannot be fixed on your own. However, if you do not have time now to contact a service center or call a repairman at home, you can resort to a temporary solution to this problem. configure the AssistiveTouch hotkey to lock and turn on.
- Open iPhone Settings
- Go to the main settings menu
- Open the accessibility settings tab
- Then turn on the AssistiveTouch function
- After that, the system will prompt you to create a special hot button on the screen, which can be responsible for locking or turning on / off your iPhone.
Attention! This is only a temporary solution to the problem. Please do not neglect this method and contact the master in time to avoid other damage.
Failure of the power button loop
Unfortunately, even Apple users are not immune to system crashes and hardware failure on the iPhone. Sometimes there are defects in components, admitted in production. The power button loop is no exception.
If it is possible to fix a software failure yourself, then a failure in the operation of the power button loop on the iPhone, which can be caused by many different factors, is almost impossible to fix yourself.
over, only a master can diagnose such a failure, so do not postpone a visit to the service center.
Careless use can also break the iPhone’s power button. As well as mechanical damage, a strong pressing on the button itself can be fraught with damage to the contacts or internal sticking of the silicone “tubercle”. which is responsible for giving a signal to the system.
If, after a strong press, the power button of the iPhone has ceased to function normally or responds to your touches intermittently, you should contact the service center.
If you find a marriage too late, you should contact the service center. Most likely, professionals will be able to quickly fix this nuisance by replacing the power button cable on your iPhone.
Damage to the power button loop
(IPhone 11 Pro Power Button Flex)
Damage to the button cable on the iPhone is a rather unpleasant breakdown that can manifest itself both instantly and gradually. Only a master can diagnose this breakdown and fix it.
The first urge to break the power button loop on the iPhone:
- The power button works by itself
- iPhone reboots / shuts down on its own
- When you press the power button, nothing happens
Burnout / damage to contacts
The iPhone power button flex cable is connected using a small mechanism with contacts. If one of them is damaged due to improper assembly / repair, moisture ingress or falling, the power button may refuse to perform its functions.
Unfortunately, contacts are not restored. A full replacement of the iPhone power button cable with a new one is required.
A reasonable solution in case of failure of the lock button on the iPhone would be to contact a specialized iLab service center so that the technician could carry out unscheduled diagnostics and tell you the exact reasons for the breakdown. Nevertheless, many users ignore this breakdown, go to the Internet to look for reasons and life hacks to fix it.
Every component of the iPhone is an important and very fragile part that can fail if used improperly or carelessly. If you value your iPhone, you must take care of its safety: do not neglect the routine diagnostics of the device, contact the service center in time, take care of purchasing a protective glass and a case for the iPhone, avoid contact with moisture and fall / shock. This is the only way to achieve good and long-term performance of your favorite device.
Also, do not forget that not all problems with the device can be fixed on your own. Even if the breakdown touches such a small component as the power button, you need to sensibly approach the situation and provide the iPhone for repair to a professional.
If the Home button is suddenly mischievous
Probably, now I will play the role of an “accordion player”, but still I will tell you about my little experience of software fixing of the Home button in the new iPad (and in any other iGadget too). Perhaps for someone it will be useful.
I have not encountered problems with the Home button before, but I often heard about them. Like, it does not work the first time, you have to press harder or, conversely, clicked once, but a double click occurs. Nevertheless, this nuisance got to me. over, what is especially unpleasant, the new iPad became naughty, the one with the Retina display.
There is a radical method using the “magic” liquid WD-40 and Arthur Malosiev has successfully tested it. over, despite the assurances of some users that this practice will not be enough for a long time and in a month and a half the problem will appear again, the phone still feels great, and after all, almost five months have passed.
So, take the iPhone, spray the WD-40 jet on the Home button, press it several times through the napkin, then spray it and press it again. After two minutes, the button comes to life.
I suppose that people warning about the short period of validity of this method simply encountered WD fakes. In my copy of the spray can with this liquid, I’m not 100% sure, and I didn’t want to pour the composition into a new, still warranty gadget. But the button began to work inadequately, from time to time it was triggered only by the third or fourth press. A web search led to the so-called calibration of the Home key and, all of a sudden, it helped. And not only me, but also Nikita Goryainov, according to whom, in his new iPad this element is practically dead, but after some simple manipulations it came to life.
So, you need to run any stock iOS application, be it a calendar, stock, calculator or notebook. After that, hold down the Power button (on top, on the edge) for a few seconds until the menu for turning off the device appears. Then release the Power button and hold down the Home button for a few seconds until the desktop appears. That’s it, calibration is complete. The process is clearly shown in the video below:
After this operation, for a couple of days now, I have not noticed a single problem with the operation of the Home button on the new iPad. joy! I hope this advice will help you too, dear readers.
Roman Yuriev
Meticulous blogger, gadget addict, bald and bearded fitness methodologist. My hobbies are technology, sports and nutrition.
IPhone does not pick up the phone or why it is impossible to answer a call?
Actually, we will talk today about what to do when “swipe across the screen” to answer a call on the iPhone does not work. And also we will find out why absolutely any user of a mobile phone from Apple encounters this at all? Let’s go!
So, the most common and widespread situation: you receive an incoming call, you take your phone out of your and to answer you need to swipe across the screen. You perform this action with a habitual gesture and nothing happens. The slider does not move, the phone continues to ring, and as a result, the call is missed. And the most interesting and unusual thing is that during everyday use (play games, listen to music, etc.) everything is “ok”. the display works as it should!
Why is this happening? There can be a lot of reasons, and it is difficult to find out which one is 100% correct, choose:
- The problem could be static electricity. Have you noticed that most often the answer slider does not move when the phone is taken out of your ? Exactly.
- The conflict is in the firmware and Apple admitted it at one time. “Glitch” occurs at the moment when, during an incoming call, the device verifies the caller’s number with the address book.
- Some tweaks (programs installed using jailbreak), especially related to the phone book, adding various qualifiers, non-native blacklists, etc. may very well cause a similar problem.
- Perhaps the problem is in the sensor, which is responsible for turning off the screen at the moment when you bring it to your ear.
- The touchscreen itself may also work incorrectly, for example, not to process pressing in the area where you need to accept an incoming call.
How to fix the problem of inability to answer a call due to the fact that the sensor simply does not work?
Naturally, the decision depends on the reason for this behavior.
- During a call, swipe your palm over the entire surface of the display several times. Please note that you need to carry out not only across the screen, but also along the entire front part (in particular, along the proximity and light sensors). In most cases, this will remove static electricity and you can pick up the phone.
- Press the power button once and then try to pick up the phone. By the way, this particular method very often helps the author of these lines.
- Use covers and films (glass) on the screen. protect against static.
- No matter how strange it sounds after the previous point. DO NOT use glass and films on the screen. I had one person who also periodically did not work the sensor on the iPhone. We decided to peel off the film with him and barely tore it off the display. this material looked more like not a film, but a piece of scotch tape (and construction tape). It’s amazing how in this situation the screen reacted at least somehow. Under such and such protection!
- Remove jailbreak. How? Here is a detailed instruction.
- If the problem is in the firmware, then restore the software via iTunes and do not use the backup copy of the phone book. To score numbers manually.
- In case of “iron” problems. carry under warranty, unless of course you have it.
Although, I really hope that the last point (visiting the service center) will not reach.
After all, in most cases, the inability to pick up the phone in the iPhone is a problem that is explained by simple reasons: statics, excessive protection of the gadget or regular “bugs” in the firmware. This means that it is quite simple to solve it.
A couple of hand movements and that’s it, you can already say “hello”.
The main reasons for the failure of the Home key
The Home button can break completely or stop working periodically for a variety of reasons. Most often, the iPhone Home button does not work due to:
- mechanical damage
- ingress of moisture inside the case of an Apple smartphone
- software failure
If the Home key on the iPhone has stopped working, it is most likely that the phone was previously loaded with software or an application of inadequate quality.
The Home button can break after dropping a new Apple smartphone or applying strong pressure on it. There are also situations when the button can break, as a result of which it stops responding to pressing or starts to slow down periodically, after moisture gets inside the mechanism. In this situation, when you press the button, you will hear a creak indicating oxidation of the contacts.
Fortunately for many owners of apple gadgets, problems related directly to mechanical damage and liquid ingress are not so common. Most Home button breakdowns appear due to a system failure. Because of it, the key does not work well, periodically slows down or completely loses its performance. In this case, the terms and cost of repairs will be insignificant.
Check the function of the key
To see if the Home button on iPhone works or not, press it at least ten times in a row. If there is no reaction to at least a couple of clicks, then there is a malfunction that affects the performance of the key.
Enabling a virtual button
The above steps allow you to determine the cause of the key malfunction and eliminate the breakdown. If your phone or its button has been exposed to strong physical impact, it will not be possible to solve the problem by dry cleaning, calibration and adjustment. The way out of the situation will be to turn on a virtual button with its subsequent display on the screen of the iPhone smartphone.
To replace a faulty key with a virtual one, you need to go to the settings, find the Assistive Touch section, and connect the function here. A new icon will appear on the screen. When you click on it, a special menu will open, in which you can control the old and new smartphone without the Home key. This method will help with any cause of breakdown.
How to calibrate when a key fails
To test if your iPhone Home button is malfunctioning due to a software glitch, you need to calibrate the key. To restore the functionality of the Home button on the iPhone, follow these steps:
- activate any application on the iPhone, for example, Clock or Calculator
- press and hold the Power button until the slider to turn off the device appears on the screen of your phone
- release the Power key and press Home until the shutdown slider disappears from the screen
10 seconds after pressing the Home key, the system will calibrate the button. The malfunction after this procedure will be eliminated if there was a software failure, and the Home key on the home screen on your device will work in the same mode.
Chemical method for solving the problem
A common cause of iPhone Home button malfunctions is dirt and dust particles getting inside it. This also happens after liquid, for example, sweet drinks, gets under the body of an old or new smartphone, or if the device is taken with dirty hands. An effective way to quickly eliminate the problem in this case will be the use of chemical cleaning agents. This can be isopropyl alcohol or WD-40. To use this method of troubleshooting, perform a few manipulations:
- add a small amount of funds to the Home button on the home screen
- press the button and hold it down until the cleaning agent penetrates inside
- check the operation Home after the alcohol has completely evaporated
Apply the chemical only to the key, not to the screen. Rough handling of the cleaning agent can break other parts of the phone, increasing the cost of repairing your Apple device.
IPhone Home button not working
And get the best deals from trusted masters.
- Compare and choose the best conditions
- Feedback from interested professionals only
- Don’t waste time communicating with intermediaries
Many apple technology owners are faced with a situation where the iPhone Home button does not work. The Home key in Apple devices is made of glass, which is subject to various influences from the outside. Rough handling of the device or dropping it from a height break the Home button on the iPhone. In case of some malfunctions, you can repair the button yourself.
The power, mute, volume button does not work
The specialized service center for the repair of Apple Service-labs is pleased to offer you our services for the repair and maintenance of mobile equipment.
We will diagnose your device absolutely free of charge, within a few minutes, and tell you what exactly needs to be changed and whether it is necessary.
Our workshops are equipped with all the necessary hardware to replace any buttons on your iPhone. The buttons themselves are always in stock, which allows us to repair your iPhone as quickly as possible. Usually this procedure takes from 10 to 30 minutes, during which you can observe the repair or wait in a comfortable waiting room.
We always give guarantees to our customers for the spare parts installed by us and for buttons they are usually 6 months.
You can learn more about our services, and guarantees for your model on the iPhone repair page
The excellent touch glass of the iPhone made it possible to abandon the keyboard, which took up a lot of space on the phones, but it is still impossible to completely abandon all the buttons. Those few buttons that remained with the device tend to break sometimes and below we will consider the main reasons for these breakdowns.
IPhone Home button not working
One of the most popular repairs is replacing the iPhone home button. This button, like Power, is pressed very often, and its mechanical parts wear out. In addition to mechanical damage, often the reason why the home iPhone does not work is moisture. We often take the device with us to the bath, talk on the street in the rain, or take it with a damp hand, and in all these cases, water can get inside the iPhone and lead to various malfunctions, and moisture is often to blame for the iPhone’s home button not working.
Typically, the Home button will fail gradually. At first, Home is not always pressed (Home is pressed every other time), then it may require stronger presses, and Home does not respond to a normal press. Well, later, as a rule, you should contact the service center, tk. when the home button on the iPhone does not work, it is almost impossible to use it. We certainly recommend not to wait for this, because replacement is still inevitable, but it is better to save your nerves and your time.
If it so happened that after a fall in your iPhone the home button does not work, then most likely you just have a loop disconnected. Buttons rarely break due to drops and if you contact a service center, the cable will be reconnected and the problem will be solved. If your home iPhone does not work, it is better not to try to press and depress the button harder. This can lead to the fact that after replacing your old button with a new one, it will not press so clearly and stand slightly lower. The fact is that with strong presses you can push through the seat in the iPhone case, and the new button will be slightly lower. If this happens, then the masters of our service center will make a small spacer to raise the button, and all the sensations will be like on a new device.
Many of our customers often think that if the home iPhone does not work, then when replacing the button with a new one, the pusher itself will be replaced (the button itself you press). The pusher is a separate part and, as a rule, does not require replacement along with the button, but at your request, the craftsmen can replace it too.
Replacing the iPhone home button is done quite quickly and, as a rule, we always have the buttons in stock, so we can quickly and efficiently replace Home and will definitely give a guarantee for repair.
Power iPhone button not working
The Power button is one of the most frequently used and pressed buttons on the iPhone, and its failure makes the device very inconvenient to use. If the power button on your iPhone does not work, you cannot lock the screen, you cannot restart the device and it becomes inconvenient to turn it on. This problem, however, when the iPhone home button does not work, it becomes extremely inconvenient to use.
The main reasons that the power button does not work in the iPhone are mechanical damage and moisture ingress, but it also happens that the cable simply disconnects, for example, as a result of a fall of the device. In such cases, replacing the iPhone power button is not necessary at all, you just need to reconnect the cable and the button will work. Unfortunately, there is no way to protect yourself from mechanical damage. Various covers and covers or bumpers will not help here. Indeed, over time, the mechanical parts of the button itself wear out and the only way out is to replace the iPhone power button. But from moisture, we can just advise you to purchase covers and covers, they will be able to hold back the ingress of moisture a little and possibly save your iPhone.
If you have a broken top button on your iPhone 3G or 3Gs, there may be another reason. The button often stops working on these models due to the fact that the metal frame of the case moves away from the plastic back cover, as shown in the picture below. At the same time, the iPhone power button itself can be fully functional, but due to a defect in the case, it is not pressed, tk. the button is displaced and the pusher (the metal outer part of the button that you press) just doesn’t press the button itself.
In such cases, you need to either replace the case or glue it, if possible, but replacing the iPhone’s power button itself will not help. Therefore, if the iPhone shutdown button does not work for you, do not rush to draw conclusions, but rather bring your device to qualified specialists who will diagnose and give an opinion on what exactly needs to be changed and whether it is necessary.
On all iPhone models, the Power button is replaced along with other elements of the device. So, for example, on 3G and 3Gs, this button is located on the so-called top cable and it is replaced only together with the volume control buttons, mute and the headphone jack. On the 4 and 4s iPhone models, this button is also replaced along with the proximity and light sensors, and on the iPhone 5 with the volume and mute buttons. Therefore, if the iPhone shutdown button does not work for you, you need to see if other elements of this loop work. If not, then most likely the loop itself is disconnected, and if they work, then the problem is in the button itself.
Replacing the power iPhone button is not an easy procedure and requires serious disassembly of the device, so we recommend that you do not make it yourself, but contact a specialized service center.
IPhone volume button not working
IPhone volume up and down buttons break much less often than Power or Home. since we usually use them less, but if your iPhone’s volume button does not work, this can be an unpleasant problem, because at the right time you will not be able to increase or decrease the sound of your device.
The main reasons for the failure of the volume iPhone buttons can be moisture and mechanical wear, although this is extremely rare. Due to moisture, corrosion forms on the buttons, which subsequently makes the buttons unusable and the only salvation is replacing the iPhone volume button. Replacing the iPhone volume button in our service center takes an average of 20 minutes, so you don’t have to part with your device for a long time.
Why iPhone buttons don’t work?
As a rule, the reasons why the iPhone buttons do not work are purely mechanical, i.e. over time, they simply wear out and need to be replaced. Besides mechanical wear and tear, there are other reasons why replacing the iPhone button is necessary. Often this is the ingress of moisture, which leads to the formation of corrosion on the button loop and, as a consequence, its failure. If with the problem of some buttons it is generally possible to use the device normally, then with some it is very difficult to use the device and your iPhone needs to replace the button.
Many people want to reduce the cost of iPhone button repair and not change it, but repair their old one. Unfortunately, in our experience, such button repairs are very short-lived and not always possible, and we completely abandoned them. In addition, the price for such work is not much lower than the replacement of the button itself, for which we can give a full-fledged guarantee. Many people get confused and come to our service center with a request to replace the iPhone button, due to the fact that the button pushers have fallen off or rubbed off. which you click. Push buttons. these are other parts, and the button itself does not work, then only it is replaced, and the pusher remains the same. Conversely, if the pusher changes, then the button itself remains the same.
For all iPhone models, button repair is not a simple procedure that requires tools, craftsmanship and quality parts. Do not try to do it yourself, we often come across cases when the desire to save only leads to additional spending. In our service center you can quickly and inexpensively replace any button and get a guarantee. For iPhone, replacing a button takes 15 to 40 minutes, depending on the model of the device and the button, but in any case, everything will be done quickly and with you.
The benefits of rebooting your phone
The benefits are undeniable, like any computer, a modern smartphone is capable of processing huge amounts of data. The more information, the faster the device cache gets clogged, which leads to software failures, freezes and subsequent problems for the user. Here is a small list of problems that harm users and prevent them from fully using the iPhone.
- Getting rid of iOS glitches
- Eliminate system braking as a whole
- Getting rid of graphic artifacts on the screen
- We kill the hung application
- Resetting the smartphone’s memory cache;
- Complete hardware restart.
- Solving many other iPhone 5 problems
Changing fonts in Settings
Everything, the problem of how to restart iPhone 5 without hardware buttons is solved. After downloading, go to the settings and remove the “Bold text”, the phone will reboot again and the system font will return to its original state.
Restart iPhone in several ways
Restarting the iPhone 6 helps to solve many problems, in some cases temporarily, but more often than not, one restart of the phone is enough to continue stable work for many months. You can reboot iPhone 5s in several ways, today we will talk about each of them separately. We will give valuable advice and, as always, attach a video instruction on how to restart the iPhone if none of the buttons works.
Hard reboot
How to restart iPhone when it is frozen so much that it does not respond to pressing the lock button? Then the so-called “hard reset” will come to the rescue of the user. With its help, it is really possible to restart the device in case of any software and hardware error. This method works on all Apple equipment, from phones to tablets of all models and configurations.
To reboot iPhone 5 in hard reboot mode is simple, simultaneously hold down the lock and Home keys, wait 10-15 seconds, the phone should go into reboot. If this does not happen, wait longer. In any case, this method will help, sometimes you just need to hold the buttons longer. The hard way will help if the sensor does not work, but it is unlikely to restore its performance, if this is not a software glitch.
With “Assistive Touch”
- Go to “Settings. General. Universal Access”
- Find and enable the “Assistive Touch” function
- Press the soft button that appears on the screen;
- Select the item “Apparatus”;
- In the menu that opens, press and hold the “Screen lock” item;
- Turn off the phone.
Reset iPhone
Rather, this is not even a way to reboot, but just a regular function to turn on / off the iPhone. Since the beginning of the entire line of iPhone models, 2, 3, 4, 4S, etc., the on / off button of the device was located on the upper edge of the device. The power button was moved from the upper end to the right one starting with the new models 6, 6 plus, 7, 7 plus. According to rumors, the 8 iPhone will also have the power key on the right side.
How do I completely restart my iPhone using the normal power-on option? Everything is simple and reliable. Press the power button and hold it for 10 seconds, until the slider with the inscription Turn off appears, now we swipe, the phone turns off. After a couple of minutes, turning on the gadget, we get a cleared cache, most of the glitches will never again make themselves felt. The method works if iOS is not frozen tightly, and all applications are working normally. But there are situations when a frozen device does not respond to pressing hardware buttons, then a “hard reboot” will come to the rescue.
On my own
The key may have stopped working due to contact with dust. Also, greasy hands can also cause breakage. Apply a small amount of WD-40 aerosol to the key, touch it several times. But use a small amount of chemical and do not let the aerosol come into contact with the screen.
In many situations, standard calibration is the solution to the Home button problem. If the Home button is not working on iPhone 7 Plus, do the following:
- Turn on any application, hold down “Power” and wait for the command “Turn off”.
- Hold “Home” for 10 seconds to make the application quit. After that, calibration will start.
To turn on AssistiveTouch, go to Settings and then open Accessibility. Item “Interaction”, then run the toggle switch “AssistiveTouch”.
Home button stopped working on iPhone 7
Even the most tidy Apple smartphone users can run into problems. Usually on iPhone 7 the Home button doesn’t work after replacing the display, but there are other reasons as well. Let’s analyze the main ways to solve the problem below.
There are many reasons for the home button breakdown, but most often it is due to poor handling. If in your case, after a poor-quality repair, the home button on the iPhone 7 does not work, it is worth trying several methods to solve the problem. Let’s analyze the main reasons.
How to solve the problem with a breakdown
With insufficient experience, the best solution would be to inspect the gadget for mechanical damage, as well as to carry out calibration. If the calibration fails, the service center staff will help. Especially if sticky liquid (alcohol, soda, etc.) gets inside the device. IPhone 7 Button Not Pressing? While the problem is being resolved, you can launch the virtual alternative using Assistive Touch. Let’s analyze the solutions in order.
Through the service center
Due to the intricacies of replacing “Home”, it is rather difficult to do it yourself. In this case, feel free to contact the service center staff. The next generation iPhone 7 scanner is motherboard-bound, making DIY repairs even more difficult. We also advise you to read the information on how to replace the Home button on iPhone 7.
Instructions for solving the problem yourself:
Home button broken on iPhone and iPad? 4 ways to solve the problem
Be that as it may, you can reanimate iOS devices without contacting the specialists at the service center. There are four ways to fix broken home button problem on iPhone and iPad.
Calibration by software
To do this, you need to open any regular application, for example, weather or promotions. Then, press and hold the power button of the iOS device until the shutdown bar appears. Now you need to keep Home until the bar disappears and the running application is unloaded from memory. The Home button will then work as expected.
Adjust the position of the dock connector
In situations where the Home button on iPhone and iPad stops responding, a little trick will help, which requires a standard 30-pin cord. First you need to place the plug into the iPhone connector, and then place your finger under the plug and gently push it from the bottom up. After that, it remains to click on Home. Now you can remove the cord and check the operation of the device.
Use aerosol WD-40.
It is possible to restore the operation of the worn-out mechanism of the Home button in the iPhone and iPad using the WD-40 aerosol known among motorists (or simply “vadashka”). This tool is used in the arms and aerospace industry, aviation, electromechanical production.
The spray is also used at home, “vadashka” eliminates the creak of doors, it can be used to lubricate bicycle parts, locks, etc. WD-40 will do, and in the case of the iPhone. just sprinkle the product on the non-working Home button, and then make 5-10 quick clicks. As a rule, it comes to life and starts responding to pressing again.
Software duplication
If the three previous methods did not work, it looks like the button is really broken and the intervention of specialists is required here. Until you go to the workshop for repair, you can use the built-in iOS function of software duplication of functions.
To do this, go to Settings. General. Accessibility and turn on Assistive Touch by clicking the switch at the top of the screen. Now press the circle that appears on the screen and in the window that appears, click “Home”. When you close the settings, you can call this button at any time to return to the main screen.
In this case, this is a temporary solution that will allow you to use the iPhone and iPad even with a broken Home button.
What to do if the Home button is not working on iPhone 6 and 6 Plus?
Professionally
Breakage signs
The main signs that the Home button is not working properly and will need to be repaired or replaced are:
- Stop responding to clicks;
- An iPhone part crunches or makes other uncharacteristic sounds when used;
- Changing the mobility of a button that staggers or, conversely, sunk into the body.
Conveniently
Fast
I can’t exit my app. Home button not working. Here is your first step
Standard 30-pin cable
- Insert the plug of the USB cable into the connector of the iPhone or iPad;
- Place your finger under the plug located in the connector;
- Gently press your finger on the connector in the “Bottom-Up” direction and press the Home button.
How to restart iPhone if the Home button is not pressed well
Tenorshare ReiBoot will help you fix your Home button problem with one click for free. Entering and exiting recovery mode can reboot your device and reanimate the Home button. Follow these steps:
Download and run Tenorshare ReiBoot on your computer (Windows or Mac), and connect your smartphone to your computer.
Click “Enter recovery mode” and enter the device into recovery mode, a lace and an iTunes icon will appear on the screen.
After that, click on the “Exit recovery mode” button, and the iPhone will reboot, the Home button will start working.
iPhone 6 / 6s / Plus: Home Button Stuck, Sticky, Unresponsive, Wont Work, Broken- 3 Fixes!!!
over, the program is able to exit any freeze, for example, freezes on the apple logo, freezes in recovery mode, freezes when updating the firmware, freezes when you call, reboots cyclically, black and blue screens, etc. The utility will allow you to solve most of the errors in the system without losing data.
Why does the home button not work on iPhone
In addition to updating to iOS 12, if we talk about the reasons for the failure of the Home button in iOS devices or it works with some lag (sticks), there are 3 reasons that can be distinguished: 1. Software glitches 2. Mechanical damage. 3. When the Home button “sticks”, clicks, sticks, does not work well or does not work at all.
Home button not working on iPhone how to display
There are still several ways for problems to arise. You just need to press the buttons with your own hands without the need to reboot the device.
Home button not working on iPhone and iPad after updating to iOS 12
One of the common problems that happen with iPhones and iPads is that the home button does not work on the iPhone 4 / 4s / 5 / 5s / 5c / 6 / 6s / SE / 7/7 Plus, or the home button does not respond to pressing and is pressed itself. And today we will find out why the home button on the iPhone does not work, what to do if the Home button on the iPhone or iPad does not respond to pressing, and how to restart the iPhone if the home button is pressed badly.
Other ways to repair the Home button
If the previous methods did not help, but you will have to contact the service center to replace the button and cable with new ones, after which the Home button starts working like a new one.
What to do if the Home button stopped working
Below we will consider a few recommendations that will allow you to either bring the button back to life, or do without it for a while until you resolve the issue of repairing your smartphone at a service center.
Restart iPhone
This method makes sense to apply only if you own an iPhone 7 or newer smartphone model. The fact is that these devices are equipped with a touch button, and not a physical one, as it was before. It can be assumed that a system failure occurred on the device, as a result of which the button simply stuck and stopped responding. In this case, the problem can be solved easily. just restart the iPhone.
What to do if the Home button on iPhone doesn’t work
Button development
Many iPhone 6S and lower-end users know that the Home button is a smartphone’s weak point. Over time, it starts to work with a creak, may stick and sometimes not respond to pressing. In this case, the well-known aerosol WD-40 can help you. Sprinkle a small amount of the product on the button (this should be done as carefully as possible so that the liquid does not penetrate beyond the gaps) and begin to click it repeatedly until it responds correctly.
Flashing the device
Again, a method suitable exclusively for apple gadgets equipped with a touch button. If the reboot method does not work, you can try heavier artillery. completely reflash the device.
-
Be sure to update your iPhone backup before starting. To do this, open the settings, select your account name, and then go to the “iCloud” section.
Select the item “Backup”, and in the new window, tap on the button “Create a backup”.
Read more: How to put iPhone into DFU mode
